Hey man it's better than 1,000 a month car payment good job
@Randy-qq8lr
7 ай бұрын
Veteran windshield tech for many years. Those cowlings are problematic. Good job bud!
@mrstyl
Ай бұрын
Thank you, sir! yes, the cowl panel was a real problem
@ashenwings3106
Жыл бұрын
I also have an 05 Durango 4.7l V8 and she occasionally stalls or acts like she's going to stall but you just gave me some info of where I should start looking
@robertclabaugh2692
Жыл бұрын
My girlfriends 2006 Durango 4.7 V8 stalled while she was driving and then she got to the point where she thought it only did it when it rained outside. I started going through the internet each night trying to figure it out. I replaced the COWL and couple other things. Finally I found a thread online that a man said he changed his wiper blades motor. I changed that and BOOM it never shut down ever again. Been going strong for 2 years now.
@mrstyl
Жыл бұрын
Thank you for sharing! there are so many things that can happen to this model, and they all have the same symptoms
@rex4765
3 жыл бұрын
Oil Pressure Sensor can do that too, mine stalls while driving and oil light comes on, ez fix and it stalled no more for me. My durango also has 244k on it with OG Motor and Transmission. But thanks for the info, gonna replace my cowl and PCM too now so I won't have that happen again anytime soon.
@JoseGonzalez-mp3ex
2 жыл бұрын
I got a 5.7 2005 and if you have a sunroof opening and taking look and the front side on each corner there's a drain and it get clogged the water goin inside the roof of the truck and fall ride on the fuse box
@jgall6701
Жыл бұрын
I’m have the same issue with my 05.. I’m now we’ll over 1200 In repairs and my mechanic can’t figure out what’s wrong with it
@357RedG
2 жыл бұрын
In my Aspen, I just had to clean my throttle body. Mine used to stall at stop signs and red lights.
@canjo4588
2 жыл бұрын
Mine was getting bad fuel mileage even after replacing my plugs and when I would come to a stop it started kind of idling ruff and just seemed off I replaced the egr valve and problem solved
@kencolle1
3 жыл бұрын
I have an 04 d 5.7.. I replaced my cowl when I noticed water leaking thru to the engine..I put a small bead of silicone when I installed the new one,no water getting thru now..haha. good info
@damianfarnsworth7474
3 жыл бұрын
Huh
@kencolle1
3 жыл бұрын
@@damianfarnsworth7474 what do you mean ..huh?
@damianfarnsworth7474
3 жыл бұрын
@@kencolle1 prior to installing the cowl?
@kencolle1
3 жыл бұрын
@@damianfarnsworth7474 no. I installed the new cowl first...then..There is a little Rubber seal that goes between the cowl and the windshield, I put a nice bead of silicone between the two so it's kind of permanent now but zero water can get through now
@damianfarnsworth7474
3 жыл бұрын
@@kencolle1 When I read it the first time for some reason I thought you were saying you did it on the top between the seal and the hood. I don't know why but, that's what came to mind
@JoseGonzalez-mp3ex
2 жыл бұрын
I have an 05 Hemi 5.7 Durango the main problem that I have is the gasket that goes to the windshield is not selling property and the water go through and fall right on top of the engine you probably have a short circuit that's why you have to replace all the coils you want to take a look at that and if you have a sunroof on it clean the drain on the sunroof they're two drains one on each corner in the front very small holes
@salingstuff8085
Жыл бұрын
I have a fix for that. It's $14.99 at Walmart it's called flex seal clear tape flex seal that s*** down to the window you will be good it will no longer leak and drip down your air compartment onto your coil
@JasonBrown-vn1zz
2 жыл бұрын
Started having the kind of problem it's started out as a rough idle at stop lights and graduated all the way up it started dying while driving did you have the same problem ?
@Ak907Queen
2 жыл бұрын
@3:50 when you look at the top seal it clearly looks like something has been between seal and hood on the right half of it in video that would of let water seep through
@damonfelder7892
3 жыл бұрын
Do I know how much u helped me no mechanic could tell me why imma change the pcm or we it's called n see what happens
@MDean-wg4de
Жыл бұрын
Can anyone tell me where the grounding strap connects to the engine block on 04 durango. I have stalling and flickering issues. I have replaced some things. The other day I noticed my ground strap hanging from the front drives side near wheel.
@chrisgrady9409
Жыл бұрын
I'm having that same problem now on mine. I've replaced O2 sensors, fuel pump, cam shaft, crank shaft. I haven't done the spark plugs yet, but I might skip that and just do the PCM board. I also thought about changing the alternator.
@mrstyl
10 ай бұрын
The PCM was my problem. If you think it is fine until you reach operating temp, it might be worth exploring
@eltoroloco1936
2 жыл бұрын
Replacing the sensor behind the right front tire fixed my stalling problem. I had a HEMI 2007 Durango. It took me changing the plugs, plug wires, throttle body, everything until I did that.
@mrstyl
2 жыл бұрын
Yep, I actually replaced that myself. Unfortunately that did not work for me. There seemed to be so many possible fixes to this one problem. It can be costly if you address every single fix.
@bluebox212
7 ай бұрын
What is the sensor called that you replaced?
@JoseGonzalez-mp3ex
Жыл бұрын
I have a 2005 and that corrosion is a water leak coming from the sunroof drain holes the location is right in the front inside of the song roof and each corner
@dugy40
Жыл бұрын
I siliconed my cowl. Done.
@franciscorivas3322
2 жыл бұрын
I assume you had to get that ECM programmed for your vehicle, if so where did you get it programmed, I have a 2001 and already went through 3 computers, great video
@RoastFlea61
Жыл бұрын
Had to do the same thing to mine, if you order it from a good place online, theyll take your info before had during ordering, and theyll program it prior to shipping it to you. Got mine shipped already programmed to the vin and mileage, plugged in and worked perfect, has been for ~25k miles so far.
@victorborges9523
10 ай бұрын
Reprogramming can be performed with a professional scanner, like Autel or Snap on models. Ask your professional ASE Certified Auto Technician.
@franciscorivas3322
10 ай бұрын
@@victorborges9523 thanks for the info, still got the durango and so far the computer is holding up lol
@lowest.tier.garage
Жыл бұрын
I have an '07 Chrysler Aspen Hemi that's been driving me nuts! I think I need to replace the ecu as well. I have problems stalling, erratic transmission issues, randomly overheated the engine and within a couple minutes was back to operating temp. What do you think? All problems seem to point at the computer.
@osmidoizquierdo525
2 жыл бұрын
2006 Dodge Durango 4.7l Adventurer with stalling & misfires. Have On & Off (with frequent resets) Engine Light with OBD codes of P0201 & P0300. Injector-1 circuit open & multiple cylinder misfires. After replacement of plugs, cylinder 1 injector, & fuel system cleaning, still have issues & most apparent in reverse. Advise by dealer that Coils not the issue. ECU and/or wire harness has been the final diagnosis. Think I’m going to order an ECU & hopefully be done with it! Looking for retailers that have the ECU…..please 🙏
@mrstyl
2 жыл бұрын
Let it run at operating temp. for 10 - 15 minutes. If it shuts off on its own, that was my symptom for a bad ECU. Good luck!!!
@osmidoizquierdo525
2 жыл бұрын
Hello, STYL! I do appreciate your responsiveness! However, I can telll you that I am fortunate that the condition has yet to get to that level. The symptoms of sputtering,misfires, & rough idle is sporadic. As sporadic as the Check Engine Light coming on for a weeks time & going off for no rhyme or reason. But I can definitely say the sputtering & turning off is heightened when in reverse like times coming out of a parking space & especially Under Load in reverse with a boat & trailer in tow. When this event happens, the exhaust smokes & fuel smell resonates. The ‘06 Durango will definitely also turn off in these instances. If the Check Engine Light was not on, it surely turns On in these times. Can hurt to just try to find a refurbished ECU as the very first diagnostic in August!!! yielded a bad ECU & the last Diag at the dealer in December was also the ECU…..after they replaced the plugs & cleaned the fuel system. So what do you think?
@mrstyl
2 жыл бұрын
@@osmidoizquierdo525 yeah, that seems like a unique problem. The ECU was the last thing I was going to try before I hung it up. Thankfully it worked, but I went through all spark plugs & and associated cables, there was the throttle body along with the sensors as well. These helped it to run smoother, but did not take care of the I deleting problem of the ECU. For what it’s worth, my check engine light came on for long periods at a time, and also went off. It got to the point where there was no code thrown even when it co Stanton shit off. There was water leaking into the hood during rainy weather, and I noticed the ECU had scum on it due to the weather. It may not hurt to visually inspect it to see if any visible damage is present. I understand wanting to make sure you know it is that unit before spending a good amount on a replacement, so I hope you can isolate.the problem
@osmidoizquierdo525
2 жыл бұрын
No, I understand & I know you do too! Thanks for the video & guidance. Like your matter, I’ve been told the ECU is all that remains. Stay Tuned! I’m gonna shop for a ECU & cowl this weekend. Regards
@victorborges9523
10 ай бұрын
Check an oil leak on valve covers to spk plgs
@natelobo9157
3 жыл бұрын
ASD relay in fuze box Ive gotten lucky several times with them.
@bloajmj2680
2 жыл бұрын
Does the asd supply or cut power?
@DavidLopez-cw8zl
2 жыл бұрын
My only tries to stall when taking off after that it’s good no problems whatsoever not even when I’m coming to a stop what’s wrong with mine?
@sipnscoot3049
2 жыл бұрын
Mine only does it when I top off the fuel tank. It’s jumpy and want to stall once in awhile. It’s not every time I fill up. ???? Any info is appreciated
@victorborges9523
10 ай бұрын
Debris at the bottom of the fuel tank is lifted when refill is done. It may clog whatever is left of a free flowing stream of fuel to the engine. A bump, and it may regain normal flow. Clean tank, change sump filter and change in line fuel filter or the 5 micron filter on the pump unit.
@AmericanSurvival001
2 жыл бұрын
Got 286k on my 2004 Durango limited she's unstoppable barely had any small issues so far (evap) my 93 360 gasser dodge truck went 500K same engine and tranny i sold it DONT BUY FORD!
@shaunraygalotera5858
5 ай бұрын
I think what you replaced there is the TCM - transmission control module. The PCM I believe is the one right in front of the fuse boxes.
@mrstyl
4 ай бұрын
I appreciate the insight. The part number is actually assoicated with the PCM, which I confirmed with the VIN when it had to be reprogrammed. There are different Durango models that may have different configs, but at least for the 04, this has been consistent.
@tokyoseoul1984
17 күн бұрын
Thank you very much! Subscribed to you now!
@yapjohn19
2 ай бұрын
It is very dangerous! 🙏🏼 thanks
@mrstyl
Ай бұрын
Yes, very dangerous! My daughter was driving this and experienced this problem while on the road. They only good thing is that it made her a better driver...
@socaldreamer5568
Жыл бұрын
I have an 05 Durango, same problem you described. Replaced everything you replaced and just replaced the EGR. Although it runs better…it stalled on me. I have a pcm on order and hopefully that fixes the issue. Did you encounter any other problems once you replaced the pcm?
@yolande.alexander4866
Жыл бұрын
check electrical leads from battery for corrosion, the silent bandit, will give error codes for camshaft, crankshaft, O2 sensors and cause stall
@socaldreamer5568
Жыл бұрын
@@yolande.alexander4866 the funny thing is, it’s not sending any error codes. The truck runs a lot better after the Egr replacement. It was stuttering really bad taking off from a compete stop…the problem is gone now. I would have thought it would have sent me an error code of some sort. Will check the leads…might as well since I’ve spent a lot time under the hood these last few weeks. Thanks for the info.
@socaldreamer5568
Жыл бұрын
@@yolande.alexander4866 the funny thing is, it’s not sending any error codes. The truck runs a lot better after the Egr replacement. It was stuttering really bad taking off from a compete stop…the problem is gone now. I would have thought it would have sent me an error code of some sort. Will check the leads…might as well since I’ve spent a lot time under the hood these last few weeks. Thanks for the info.
@yolande.alexander4866
Жыл бұрын
Connection for battery harness looked fine but upon inspection, had to cut the two wires on the positive side to inspect and found the corrosion in the strand, bought a repair splice wire (the two wire splice) from AutoZone and followed directions for repair and codes couldn't be erased upon startup had to drill the holes wider in order to cleanly insert each wire in . Cleared codes and no more problem at startup, this after changing the camshaft sensor and it still was giving the error. Stalling at pull off and while on highway with high mph .whole lot cheaper fix than the cost of PCM.
@mrstyl
Жыл бұрын
Once I replaced it, the problems went away regarding the stalling. Since it is an older vehicle, I am encountering new problems. I had a crank issue recently where the car would crank, but not start. That is a new video I posted. I have also had RPM issues related to the ignition coils, and I still have the small evap leak issue which nobody seems to be able to solve. That is a quest of mine to fix!
@rachelbuzzo1865
3 жыл бұрын
I’m really trying to avoid going to the shop again because I already have my car in there three times in one month and I don’t know why this keeps happening
@doristroino6273
3 жыл бұрын
It"s time ...Things just get old..
@rachelbuzzo1865
3 жыл бұрын
I have a 06 and I just got the power steering pump changed the belt and 2 hoses because once they change the power steering pump they said the hoses there’s too much pressure and then they broke so they replaced them it’s been two months and now I started my car in five seconds and I shut off I did it again shut off keeps shutting itself off at this point now it’s not turning over at all the lights and everything works the battery just got changed a month ago and there’s an lightning bolt engine light and oil light on and I believe it’s the electronica throttle does that sound right though if I change the electronica throttle will that fix it do you think
@ritab500
2 жыл бұрын
How to check and see if transmission fluid flow is not clogged up
@davidmaroni2774
2 жыл бұрын
Nice video. I had a 2005 Durango that stalled and just needed the throttle body cleaned. Im having an issue with a 2007 aspen now. The motor ran great until after replacing catalytic converters and now it sounds like it might have a lifter tick. I fear the p0164 code that went up after the repair might have damaged the engine with heat and back pressure. Im completely lost diaging this issue. It seems to happen most when going over a bump or cutting the wheel to the left, yet the sound is coming from the drivetrain
@mrstyl
2 жыл бұрын
These problems never seem to be easy to figure out. The symptoms seem to be similar for that code, but there could be a number of issues. There were a number of sensors that are tied to this code as well. Does it cut off at operating temp while it is idle?
@sipnscoot3049
2 жыл бұрын
Replace all your lifters. I did. It runs amazing now. The stall issue I had too. Only after I fill it up with gas. But changed the carbon exhaust filter. Went away. For now. The filler neck is too small. So it gradually will go again. Cause gas gets into the filter
@goerolucas323
2 жыл бұрын
It was my crank shaft position sensor
@highbird1052
Жыл бұрын
Look at you exhaust lol shes ticking at the manifolds you bent or cracked something your motor is fine i promise
@highbird1052
Жыл бұрын
Use middle grade gas never regular you'll never ha e lifters go im at 660 km in mine never touched the lifters once
@SilverConundrum
3 жыл бұрын
Thank you. My vehicle is having the same issue. I hope will your help I am able to fix it
@mrstyl
2 жыл бұрын
I hope you took care of your problem!
@STELLABeauty
3 жыл бұрын
If it's the Ecm, does it give you "p code" and flashing engine light?!
@STELLABeauty
3 жыл бұрын
MIne does. What's that mean?! Mechanic cant figure it out because it's not throwing out a code?!
@connorpoore3043
3 жыл бұрын
Flashing engine light is a cylinder misfire
@mrstyl
3 жыл бұрын
I did not receive any code whatsoever. I knew there were problem with the vehicle though. That was another tell tale sign that the computer was going bad. It did not display any code, and it shuts off after getting to the normal operating temperature.
@robertmedina6875
2 жыл бұрын
@@STELLABeauty get a new mechanic…. He has no formal training. Good luck
@nickvannett3841
2 жыл бұрын
I have 04 darango 4.7 engine light on sometimes. It will stall now and the or won't start right away just crank over. I checked it out at AutoZone and says the cam sensor intermittent at bank 1 but the guy at AutoZone says it's not that probably a connection so confused
@selina1964
Жыл бұрын
Yours sounds like what mine is doing.. I replaced all these sensors and still having the issue drive it and then I try to recrank it and it won't start you got to wait a while.. I'm not sure if I'm ready to do the computer yet
@hectormedina4158
Жыл бұрын
So did you figure out what the problem was or what and what did you change and did it make a difference
@tpsyturvy6987
3 жыл бұрын
Mine is problem after problem,'06 model.
@RV-ds5uf
3 жыл бұрын
Same here!!😒
@duece2timez568
Жыл бұрын
I'ma see if that's the reason mine keep stalling because it's gotten worse over time all my fuses good oil good sparkplugs new 🤷 so now I'm guessing it's the fuel oump
@ayonecollins6729
3 жыл бұрын
Mine won't go over 30 mph and cuts off at a slow turn any ideas?
@jmemixx
3 жыл бұрын
Probably one of your fuel injectors. Mine wouldn’t go above 60 and it was one of the injectors that was blocked inside with gunk. You can replace all if you want to and there like 10-15 bucks each though. Or you can find which one it is to save you money. Or maybe just put some injector cleaner every time you fill up and see if it unclogs it but i doubt it
@miltonmitchell4290
2 жыл бұрын
Mines was tps sensor
@claudiaivettereyes-fernand8233
Жыл бұрын
did you lose power at any point or have something like explosion?
@mrstyl
10 ай бұрын
No explosion. Car just turns off mid drive when at operating temperature
@tamarajohnson8548
2 жыл бұрын
I am having the same issue and was looking up for the ECU, but was a bit confused by the options. I have a limited edition 2005 and it's a 4x2. Could you help me determine what I need...it mentions a 4.7L and a 5.7L. Do I get the 4.7 L?
@mrstyl
2 жыл бұрын
You should be able to determine that by the VIN of your limited edition The ECU has to be programmed specifically for your vehicle, which is determined by your VIN anyway. Try this link to start with. You can probably find cheaper options, but at least I got what I asked for on this site: carcomputerexchange.com/dodge/durango/2005-05-dodge-durango-ecm-pcm-engine-control-module/prod_138.html?campaign=15445611790&content=565985117028&keyword=&gclid=CjwKCAiA24SPBhB0EiwAjBgkhlOgzZrsZ-wiCwGIBvomcfxee6_QD8IOgcIpZ-5-c_msAuj6INucsxoCMmgQAvD_BwE
@mrstyl
Ай бұрын
Ohh this is so late, but your car should show what Litre you have when you openj the hood.
@JoseGonzalez-mp3ex
Жыл бұрын
This ain't happened and the site where the fuse box is checked the fuse box I take it apart and clean it with WD-40 and a toothbrush
@michaelsalter1055
7 ай бұрын
How did you get the battery tray out?
@mrstyl
4 ай бұрын
did not need to remove the batt. tray on the 04.
@sergio23988
2 жыл бұрын
I have a 5.7 hemi 2004 stopped working at 100k been sitting in my garage for over 8years
@raulrobles213
2 жыл бұрын
Where did you get the pcm computer at. Mine has been doing the same thing.
@mrstyl
2 жыл бұрын
I went to carcomputerexchange.com. It was pretty quick and straight forward. They will ask you to send in your damaged unit. Just make sure that is what the problem is.
@johnwayne7128
5 ай бұрын
How much did the PCM cost you
@user-dz9sc2ph7y
4 ай бұрын
Thank you for your video
@mrstyl
Ай бұрын
Yes, no problem! I have watched a lot of youtube videos that helped me. I hope this helped your problem, if you had one...
@doobey77trill
3 жыл бұрын
Good video.You could've went to a junkyard and got the pcm for a lot lot less though.
@damianfarnsworth7474
3 жыл бұрын
Programming used modules can be an issue on newer cars
@mrstyl
3 жыл бұрын
Yeah, I thought about that, but you have to get the PCM reprogrammed for your specific VIN. I was not sure how to do that outside of the companies online who replace them for you.
@mhoffer11
2 жыл бұрын
@@mrstyl I’m glad I read this comment I was about to head to pic n pull. Lol now I know it’s vin specific. You now helped me twice in 10 min bahahaha. I’ll subscribe and like for that. Cheers
@salingstuff8085
Жыл бұрын
Fuel pump
@elijahcamacho1152
8 ай бұрын
Where did you get it from?
@-rndels-
Жыл бұрын
Where can i order 2nd gen durango parts?
@haggard.society8681
Жыл бұрын
Did it throw a code ?
@mrstyl
Жыл бұрын
By the time it started malfunctioning, there were no diagnostic codes to read. That was another indicator of the computer module failing
@nathanperkins3416
3 жыл бұрын
I got one same color it's a turd on wheels nothing but trouble
@dnastats
2 жыл бұрын
I have 2 this is the 1st time I've had any issues
@shaundavis1409
3 жыл бұрын
Where did u get the remand ECU FROM
@mrstyl
3 жыл бұрын
I went to carcomputerexchange.com. They seemed to have a decent rate compared to a few other sites. You will need the VIN of your car so they can program an ECU for you. They will also send you a return envelope for your damaged ECU.
@JUNIORMICH
11 ай бұрын
What did you pay for that ECU?
@mrstyl
10 ай бұрын
Just under $200. I had to send in the bad ECU so the company could refurbish it
@einsteincasino8539
3 жыл бұрын
Just get rid of it!!😁
@mrstyl
3 жыл бұрын
I could not let it beat me!!!
@damianfarnsworth7474
3 жыл бұрын
Did you enjoy buying parts at random?
@mrstyl
3 жыл бұрын
It was a pet project of mine. I made it a point to get the car working for my daughter. It was not completely random. The parts I ordered were based on symptoms I experienced with the car, plus other videos I saw on KZitem. This site has been extremely helpful to me, and I just want to contribute my experience.
@dre.supreme
3 жыл бұрын
Don't but a dodge. Simple and plain.
@doristroino6273
3 жыл бұрын
some thing JUST GET OLD
@dantebrytant5285
3 жыл бұрын
It's a dodge that why it stalling they suppose to do that it normal
Пікірлер: 126