This video was a huge lifesaver for the seal. It was my first time doing anything to my own vehicle, and it was the perfect guide. Thank you so much.
@Khanalajite
3 жыл бұрын
Thanks for the video, huge help. Got it done in no time flat. A nearby shop was telling me 5 and a half hours of labor plus the parts.
@frankteller6981
2 жыл бұрын
Best vid I've seen for this , good job
@Underthe5
3 ай бұрын
I appreciate this video a lot
@mrtrillionfold
3 жыл бұрын
Excellent video!!!! Thanks for the info!!!
@Acobolan
3 жыл бұрын
thanks for posting. might have to do this or get it done soon
@demetreiusmayes5403
4 жыл бұрын
Great video bro I gotta do mine today. Damn bolt came lose
@omaralvarez9764
4 жыл бұрын
From the club my brotha.
@gailliardander
4 жыл бұрын
Thank you !!!!!!! My Brotha
@noahstiles4844
4 жыл бұрын
Khalil here again dropping knowledge!
@khalil2236
4 жыл бұрын
Noah Stiles always here to help!👍🏾
@scotthogan4558
2 ай бұрын
You replace the bolt because it’s a torque to yield bolt like a cylinder head bolt proper spec is 111 foot pounds plus an additional 76 degrees. These specs are easily found if you’re going to post instructional videos you should at least use proper tools and procedures I’m sure that you didn’t know that’s why I’m telling you this I hope this helps you in the future videos that you make make a simple google search will show you should about any automotive procedure that you can do. Other than the torque spec the video was good. Just a suggestion though if you were to remove the 2 lower motor mounts you could get a lot more downward room without messing with the cradle
@spydrmngenius
3 жыл бұрын
Good Vid Guys!!
@MikeHunt-pm5sj
Жыл бұрын
what is the correct FT/LB of torque the bolt on the harmonic balancer?
@Deleted_9393
Жыл бұрын
How can I change the crankshaft position sensor myself
@Co1eTrain84
Жыл бұрын
how long is the hose clamp?
@DjSmoothNY
2 жыл бұрын
Great walk through. I'm going to build up the confidence to do this myself since Chevy quoted me 850 plus tax. They said after installing a new one the car needs an alignment?. Any suggestions or feedback??
@khalil2236
2 жыл бұрын
I’ve never heard of anything regarding an alignment after swapping a harmonic balancer. I definitely push you to DIY😎
@DjSmoothNY
2 жыл бұрын
@@khalil2236 Okay thank you brother. I will try on my own.
@Conshnz
3 жыл бұрын
Got to do this on my Impala SS. It got the wobble too. 😂
@jerriabarton
Жыл бұрын
Me to in my 5.3 gxp
@customyamaha
Жыл бұрын
2007 GXP here it's been wobbling for almost 21000 miles
@anthony8578
4 жыл бұрын
How do you lower the engine again ? I didn’t see how you guys did that
@khalil2236
4 жыл бұрын
Anthony Villarreal support the subframe with a jack and remove subframe bolts and lower with the jack
@kaylaquezada5681
3 жыл бұрын
Would you happen to know if a 05 Pontiac grand prix 3.8 harmonica balancer , fit a 05 Pontiac grand prix gxp 5.3
@khalil2236
3 жыл бұрын
It will not fit
@kaylaquezada5681
3 жыл бұрын
@@khalil2236 okay, thanks
@kevinhumphrey932
3 жыл бұрын
Why did you change the balancer the reason I ask is that my 05 5.3 GXP makes a intermittent noise that sounds like main bearings knocking
@khalil2236
3 жыл бұрын
The balancer was beginning to wobble and sometimes had a mild chirping sound while spinning
@Jhoss003
3 жыл бұрын
Can you explain how to remove the bracket out of the way from the sub frame bolt
@khalil2236
3 жыл бұрын
What bracket are you referring to
@Jhoss003
3 жыл бұрын
@@khalil2236 the ones covering the subframe bolts
@Jhoss003
3 жыл бұрын
@@khalil2236 can you text me 4054887952 and I can show you what I’m talking about. Really struggling
@khalil2236
3 жыл бұрын
@@Jhoss003 ohhh those are annoying and ironically I’ve only seen them on some LS4s. But i ended up having to take the bumper off just to get to the bolts that secure the bracket. You MIGHT be able to get away with removing the splash shield but im not 100% sure. I feel like i had already tried that previously
@Jhoss003
3 жыл бұрын
@@khalil2236 okay thank you
@rileysmith1486
2 жыл бұрын
did you take the back bolts of the subframe loose or no?
@khalil2236
2 жыл бұрын
I believe I did just the front and it gave me enough clearance
@cammims7645
3 жыл бұрын
what Impact gun you Recommend?
@khalil2236
3 жыл бұрын
I have a Milwaukee 1/2” M18 Fuel
@cablrus1885
2 жыл бұрын
Dudes i need help. Mine exact same issue. Balancer wobble. Got parts but what is that rattle at start up. MY IMPALA SS DOiNG THE SAME n it sounds like crap. Help please on that rattle at :29 seconds
@khalil2236
2 жыл бұрын
Its your starter. Not that its necessarily “bad” but the part in there that retracts from the flywheel is just retracting slower than it should. I’ve heard of people lubricating them before but i feel like you might as well replace it being that you have to remove it to lubricate it anyways
@dakotahall9972
3 жыл бұрын
Do you have to drop the subframe?
@khalil2236
3 жыл бұрын
dakota hall not completely drop, but you do have to lower the front of it
@eddiesalazar6002
5 ай бұрын
i dont get how the whole pulley didnt turn with the impact though, when i try to break it with the impact the whole thing just moves with it
@khalil2236
5 ай бұрын
Heat that bolt with a torch. That should help break it free with the impact
@jimgreen1554
2 жыл бұрын
Without showing jack points and stand positions this video is useless. I had so much hope that I had found help.Half the information is like no information. Too bad!
@khalil2236
2 жыл бұрын
It definitely does show all of that. If you would like to be spoon fed just say that :)
Пікірлер: 47