What are the symptoms what's the reason your replacing ignition switch
@ryanelkins8081
4 ай бұрын
Some people online said they switched it because it would cause the dash and lights to flicker on and off and then throw a code for the fuel sending unit. Some people said they go out a lot. Code U1411.
@TCB84
10 ай бұрын
Thanks for the guide. What issues were you having with the rig that prompted the repair?
@fozzietaylor3556
Жыл бұрын
Very helpful bub thanks a lot to you and your helper. I’ve had to go back and watch this video several times. You know the problems with ignition switches on these jeeps 😂
@jadenr1514
Ай бұрын
This video helped my wife and I out so much. Thank you sir. God bless
@okcvet1st
Ай бұрын
Thanks for watching!
@GhettoFabulous99
11 ай бұрын
Thank you very much for making this video. It makes doing this job so so much easier. You definitely earned my sub. 💯🇺🇸💪🏻
@antoniocarreras
4 ай бұрын
I replaced same part and still not cranking :(
@hc8807
3 ай бұрын
Thank you!! For this video
@Hondalife_8
Ай бұрын
What were the symptoms?
@Emiranda0426
2 ай бұрын
So if you change the switch, you won’t have to change the module to because of course the kid needs to get programmed right with the new switch
@okcvet1st
2 ай бұрын
@Emiranda0426 Not sure if I'm understanding you correctly. There's no programming required at all to replace this style ignition switch. The lock cylinder is not being changed, only the switch which is mounted to the back of the lock cylinder.
@urasssmine
10 ай бұрын
Thank you for the video very helpful. I have a question. Say you did all this and your car still doesn’t turn on, power and heat comes right on with no problem. Can the the problem be the Key Fob ( the chip). I noticed my car won’t turn on without the original key, so can that be the issue?
@jimmycochran9256
Жыл бұрын
What was the reason for changing it I’m having a problem with cylinder 5 miss fire and dash cluster not working coil and cam shaft sensor both been replaced Runs fine after restarting once or twice thinking this as next step 🤔
@andyseamaster
Жыл бұрын
In my experience, all the job is done easily if you first remove the blend door actuator wich is behind the ignition assembly. It's an easy task and doing that will prevent a lot of effort in removing the ignition key assembly. Hope it helps. Thanks for the nice video.
@bigal7561
Жыл бұрын
Hey Oklahoma. I"m down south (Between Durant and Ada) Good vid
@jfishtale4916
9 ай бұрын
Thanks man. Great video. Made it realy easy
@nwheeler1048
11 ай бұрын
Thanks, just changed mine out and your video helped a lot. A little tricky getting the assembly back in place after changing the switch but otherwise pretty straight forward.
@okcvet1st
11 ай бұрын
Glad it helped you out! Thanks for watching!
@UnaSolaTorah
Жыл бұрын
Excellent.. thank you!
@BigTrappaBenzo
8 ай бұрын
What were the symptoms?
@marcobravo7516
Жыл бұрын
Good job ! Thank
@stasdubrovin
Жыл бұрын
Thank you! Your video helps me to change the module.
@okcvet1st
Жыл бұрын
Thanks for watching!
@joeyi8738
Жыл бұрын
do you have to have the dealer reprogammer the keys afterwards?
@okcvet1st
Жыл бұрын
No programming is required. You're not changing the key transponder, that's what is being taken off as you remove the switch.
@joeyi8738
Жыл бұрын
@@okcvet1st forgot to mention doing a ignition lock cylinder also.. do you know if I need reprogramming?
Пікірлер: 28