Only the very last plate is turned clockwise to lock it in, the bolts and springs are supposed to be more flush with the pressure plate
@arcoverdetony
2 ай бұрын
You have to get that spring holder lined up with the pressure plate gears the same thing. Your clutch plates right on that front attachment connects to those teeth. Look at the back of it and the front of it the back of the spring thingy and the front of the clutch basket
@tolga54321
2 жыл бұрын
Had this exact problem on my 04, first of all ONLY one friction plate on the last tangs. Your bearing should have a spring under it, yours looks like it's missing. When putting the case on, keep the rod in and lift it a bit. Half a littlefinger/full littlefinger. Hope this helps
@philiptaylor3533
3 жыл бұрын
you have two friction plates instead of one in the wrong place and your washer in front of the actuator bearing is missing , it should be infront of that bearing .
@JonathanMeraz-bz2pf
4 ай бұрын
Hey man i was wondering if you were still active here, if so i was wondering if you could help me out with that part you were talking about, im also having this issue in the 2007 zx6r, was wondering if you could help check the part that i need, thank you
@tylerbit4059
4 ай бұрын
In the same boat, I have a 2000 zx6r. Any updates?
@robertgisthebest
5 жыл бұрын
My 01 model has a spring that goes under the bearing. There is also a small shim under the spring. The spring rests on a collar under the bearing and keeps the bearing snug against the pressure plate. I bet you are missing the spring and possibly the shim too.
@M6xSniper
5 жыл бұрын
Yes i have ordered the spring, bearing and shim should be in soon but thanks I looked over the parts list and seen I was missing those I'll update if they fix the issue
@robertgisthebest
5 жыл бұрын
@@M6xSniper Excellent, I figured you had probably solved it, but thought I would post in case anyone else had the same issue.
@angellg237
5 жыл бұрын
Did they fix the issue?
@M6xSniper
4 жыл бұрын
Yes the clutch feels like normal again after the shim and spring got installed
@dwhizz89
4 жыл бұрын
robertgisthebest I have just changed the clutch on my 01 do I have to put the last two fibres in the secondary basket holes or just the last fibre one as per the manual
@melaniecollins6762
2 жыл бұрын
All it is is the little spring on top of the clutch cover under the clutch actuator rod just had and fixed the same issue
@M6xSniper
2 жыл бұрын
Mine was the shim between the needle bearing and the little spring , gave it enough clearance to fully engage and disengage the clutch but that's also a good thing to check if your having this issue
@loopygzz4559
2 жыл бұрын
Hey can u help me my rod is like yours it won't engage
@itsbloodyvids
Жыл бұрын
@@M6xSniper what you do to fix the problem
@M6xSniper
Жыл бұрын
@ITSBLOODYVIDS mine was the shim or little washer looking peice between the needle bearing and spring, gives it just enough room to be in line
@brockzack8370
6 ай бұрын
@@M6xSniper where is that , I got this issue currently.
@dannydevito5828
4 жыл бұрын
Bro i have the same problem is there something i can do
@M6xSniper
4 жыл бұрын
92180-0149 is the shim part number sits in front of the needle bearing
@KararAsi848
Жыл бұрын
انا تخلصت من احد العينات جعلتهن فقط ٨😅😅
@itsbloodyvids
Жыл бұрын
Having this problem on my 2004 zx10r
@coreyhickman9082
4 жыл бұрын
What happened to the parts? Like why did this problem happen?
@M6xSniper
4 жыл бұрын
There is a shim that goes between the bearing amd the cover that was missing, it provided the space needed to align the shaft to the correct spot
@coreyhickman9082
4 жыл бұрын
@@M6xSniper Did it just disappear or did someone not no what they were doing lol Im having a studder off the start problem with my 06 636 and came across this video I havent looked into my bike yet just trying to collect info
@M6xSniper
4 жыл бұрын
@@coreyhickman9082 I found out that it went missing but it was my clutch was unable to disengage all the way due to the shim missing
@fireballcbrljr5966
4 жыл бұрын
What shim yall talking about
@fireballcbrljr5966
4 жыл бұрын
Am having the same problem
@rohankhongthohrem6596
2 жыл бұрын
Wrong placement friction plates 😂😂
@M6xSniper
2 жыл бұрын
Actually no, it was the shim and spring by the needle bearing that was the problem. The fruction plates were correct for my set
@jabbacoola1
3 жыл бұрын
That plates or steels are too thick pushing ur throw bearing out too far u either have the wrong plates or steels!
@M6xSniper
3 жыл бұрын
Turned out that I was missing a shim next to the needle bearing giving me the extra bit of length I needed I cant remember the part number but its the washer that sits on the needle bearing I had lost
Пікірлер: 47