Thank Grandpa it was a help full video now i learn new thing and it save me $$$.
@ROADGLIDER010
6 жыл бұрын
Hi, I want to do the same thing on my V Rod night rod special '07. Is this the same procedure or does my bike has something different going on? last but not least, I don't have a impact gun. Can I brake the nut loose with a wrench and a clutch holder tool? and do I need special tools to line up the clutch plates? thanks a lot!
@209golightly
9 жыл бұрын
I have an 07 witg trask turbo.. lookibg to upgrade the clutch i need part numbers or advise...
@nonavy2004
15 жыл бұрын
You guys r Crazy!!!! Goods Stuff.
@NICKBICKEL1
12 жыл бұрын
Use this vid along with 1130cc.com and you can't go wrong. Awesome job guys.
@donaldclos2196
2 жыл бұрын
Very helpful. Thanks a ton!
@rscrod
2 жыл бұрын
Glad it helped out
@michaelhabada3493
4 ай бұрын
Does the main nut need to be torqued??
@12ibsen
11 жыл бұрын
Do you have a video for change brake pedal on vrod 2002
@guimaraesborges2155
3 жыл бұрын
Muito bom video, parabéns.👍
@rscrod
15 жыл бұрын
The AIM plate involves alittle more detail...springs and shims(washers) Not hard to do..Just follow the instructions and you will be ok. I still have mine as a back up..lol
@lifelessmetal7195
3 жыл бұрын
Thanks for the video my 03 vrod clutch is starting to slip (or atleast I think thats the problem) gonna probly get it checked out to make sure and replace it myself
@rscrod
3 жыл бұрын
Test it yourself or with a friend. Ride bike at 55mph 4th and 5th gear. Go wot and watch the rpms vs speedo, if rpms climb fast and mph is slower then usual, possibly a bad clutch. Either way I would change it out and give old clutch to drag racer.
@lifelessmetal7195
2 жыл бұрын
Yea so I got the slipper clutch started the install with no problems till I put the new clutch in the last two fins wont go in its slides on and then stops any advice?
@rscrod
2 жыл бұрын
@@lifelessmetal7195 go the video on KZitem. Channel is rscrod.... It will show you that the last plate goes over one slot. Email me
@nathanharshbarger9222
4 жыл бұрын
And thank you for the video
@rscrod
15 жыл бұрын
Just having FUN !
@tomheringer2047
4 жыл бұрын
03 V-Rod? What happened to the cover with the 100th anniversary badge?
@rscrod
4 жыл бұрын
Wrapped in paper and put in a box for safe keeping
@petarkoychev4782
Жыл бұрын
Using impact wrench is OK. Even for installation, because over tightening can be controlled. That is not the problem. What the guys have not showed in the video is tightening of the nut. It is very important, because the tightening goes in opposite direction of the engine rotating, which should be avoided as per the HD service manual. Use the clutch hub holder to avoid that. I am not sure how in this case the guys tightened the nut up to 220Nm as per HD service manual recommendation. Just to compare how big is this force - my 16inches tire on the car requires tight force of 120Nm on the nut during installation of the tire.
@rscrod
Жыл бұрын
Rewatch the video. He is facing the bike. Right tightly lefty loosy. We use the torque wrench to secure the nut.
@Fuaarrkk
9 ай бұрын
Tightening the nut would rotate the motor the correct way. From crank side it would rotate anti clockwise as needed. The danger would be when trying to loosen the nut, if the motor turns over while trying to loosen the nut it would rotate the incorrect way
@michaelgioia3080
9 жыл бұрын
What size socket is needed on the impact gun?
@reventon4547
2 жыл бұрын
I know it's a bit late, but I couldn't find this info anywhere. For anyone else looking, it's a 29mm, deep well, thin wall socket. I used a half inch drive torque wrench to 70 to 80 foot pounds.
@shawn68able
9 жыл бұрын
Hahahaha, Lol ! Just give it the old tap tap taparoo ! Happy Gilmore
@poncoolride
8 жыл бұрын
How does a slipper clutch work, and what is the advantage of it?
@jake66
4 жыл бұрын
Helps when downshifting at higher rpm. Your rear end won't get loose.
@JL-wf2wp
2 жыл бұрын
@@jake66 aka "noob clutch"
@droneops3578
2 жыл бұрын
Do u need to buy a pressure plate aswell as clutch plates?
@rscrod
2 жыл бұрын
It comes as 1 piece. Slide hub out, align flanges, loosen bolts if need be and slide in the new one torque down the 4 bolts.
@nathanharshbarger9222
4 жыл бұрын
Where did you purchase the 08 slipper clutch?
@rscrod
4 жыл бұрын
Vreeland HD. Have your dealer do a parts search. Call dealer and have them ship to you.
@bri1360
5 жыл бұрын
How often do those bikes need a new clutch
@rscrod
3 жыл бұрын
When it goes bad. Possible test. Ride at 55mph, get on the gas watch to see if rpms go up and bike climbs real slow in mph. Most likely it is time .Slipping g clutch.
@vitablogs3458
7 жыл бұрын
I need your help my 2009 v rod muscle is chattering on hard acceleration could it be my clutch too? plz help me thanks
@rscrod
7 жыл бұрын
Micheal Treeman launching hard. if you feather the clutch yes it will chatter. a flow control valve can help. once clutch lever is released it is fully engaged. Do not feather the lever.
@vitablogs3458
7 жыл бұрын
thank you for the quick reply no I'm not feathering the clutch it chatters when I get on it in all gears but smooths out when I let off the troodle at high and low speeds it feels like it's something in the gear box/tranny
@vitablogs3458
7 жыл бұрын
rscrod by the way I used an Impact gun to remove the front pully because I did add a 300mm wheel to my v rod muscle do think the impact gun did some damge To the clutch plates or something ? any help is truly appreciated
@rscrod
7 жыл бұрын
Micheal Treeman i would pull the cover and check the clutch pack. check plates for burning. just do not squeeze the clutch lever with the actuator not bolted on.
@sauroleite7273
9 жыл бұрын
crazy..
@Iswhatitisssss
Жыл бұрын
Easy as that eh, nice.
@rscrod
Жыл бұрын
If tabs won't align up, just tap the tab to aling it. You will not hurt anything. Slipper has 4 bolts holding the plates. You can loosen them up if need be. The torque spec is on here somewhere. It is not in the manuals.
@tonystokley8916
2 жыл бұрын
Anyone know what size socket to use?
@rscrod
2 жыл бұрын
pn 8008M 30mm or 1 3/16 162ftlbstighten backup add red loctite
@rscrod
8 жыл бұрын
wait to you try to take mut off. the finish setting was done with wrench and a 4 ft cheater bar.
@tonystokley8916
2 жыл бұрын
What size nut is it?
@CRUZROYHelicopters
2 жыл бұрын
did not show how to change plates ???
@rscrod
2 жыл бұрын
You need to look at the manual. or. It is simple to watch how you take them out to put the new ones in. They just alternate pad to plate. Big one is the first one. It is bowed a tad. Next time I would buy the slipper clutch assembly. That is what's shown in video. Hope this helps.
@CRUZROYHelicopters
2 жыл бұрын
@@rscrod How was the exhaust to takeoff I have screaming Eagles
@rscrod
2 жыл бұрын
@@CRUZROYHelicopters they can be a pain the rear mufflers slide off. There is a clamp if it has the figure 8, that's what it looks like . or 1 clamp for ea h one. Loosen them up. Take rubber mallet and tap them off. Wiggle them up an down to break loose the carbon.
@Z1slayer
8 жыл бұрын
OH ya....you are not finished until you put the oil back in..
@rscrod
11 жыл бұрын
nope...
@rscrod
9 жыл бұрын
Send me email with number to rchesnutte@gmail.com
@michaelxwhite
3 жыл бұрын
I wouldn't of used the impact. I wouldn't want all the impact vibration through my motor.
Пікірлер: 60