I cut all the bars out of my sawdust exit port and have had no issues with sawdust After
@eldoradowoodcrafthobbies3888
4 жыл бұрын
I went with WM as well also use windshield cleaner and water to correct sawdust buildup. You look steady on feed rate keep up the good work.
@endlessmountainwoodworks4278
4 жыл бұрын
Thanks, and all things considered I would probably go the woodmizer route myself if I were to do it again. I plan on upgrading this mill in a few years and that seems to be what I will end up getting.
@55points
5 жыл бұрын
👍 continuous improvement is key man.. keep going.
@endlessmountainwoodworks4278
5 жыл бұрын
Thanks, will be trying this out and fine tuning it. If it ends up working good I will be most likely getting a box of 10 to start. So far I am impressed.
@neilmacleod5371
4 жыл бұрын
Wider guides for the wider blade ?
@HWoodCreations
2 жыл бұрын
Does the HF model come with electric start or did you add it?
@oldschooldiy3240
3 жыл бұрын
How much less water would you use, if you adjusted it to actually fall on the blade, instead of run off the side like it does?
@endlessmountainwoodworks4278
3 жыл бұрын
I have switched to not using any water and it cuts much better. I have checked that the blade and guides are not getting hot and they seem to stay cool.
@rogercoder1469
5 жыл бұрын
Would some shields over the wheels stop the sawdust from clogging?
@endlessmountainwoodworks4278
5 жыл бұрын
I am not sure what you mean. If you are talking about the carriage wheels I plan on mounting brushes in front and behind them. I think that would be a good solution to stop sawdust from building up in the grooves. As for the sawdust clogging up in the mill I think I will remove part of the screen where the dust exits. There are 3 or 4 steel bars there with about a 1/2" gap between them. I plan on removing just the middle one to see if that helps.
@rogercoder1469
5 жыл бұрын
@@endlessmountainwoodworks4278 Yea that's what I was talking about
@revrickw
4 жыл бұрын
You did not really mention if the 1 1/2" blade required any type of modification to the saw? A question below asked about if wider guides were necessary went unanswered, so far.
@endlessmountainwoodworks4278
4 жыл бұрын
I did not change the guides, I was able to adjust them far enough to get the blade cutting like it should
@galanjones8123
4 жыл бұрын
Does the 1-1/2 in blade work better
@endlessmountainwoodworks4278
4 жыл бұрын
In my opinion yes but it requires much more power to turn it. If you do the 13hp swap you can cut faster and straighter than the 1 1/4". The cons are that it costs more and with smaller diameter band wheels like what this saw has will not last as long. I have only been using it for cutting large or hardwood, the rest of the time I use 1 1/4".
@silvertounge69420
4 жыл бұрын
Is the roller feet on backwards is that why it kind of wobbles or I should say it looks like it does
@endlessmountainwoodworks4278
4 жыл бұрын
I believe that they are. I need to get them changed around. Many other commenters have noticed that as well.
@pstoneking3418
2 жыл бұрын
Way too much water flowing. You only need a couple drops per second with hard woods.
@raykemry954
5 жыл бұрын
The better blades are worth there weight in gold. Harbor freight blades are very cheaply made. There are even better blades than woodmeizer.
@endlessmountainwoodworks4278
5 жыл бұрын
I am happy with the blades I have been using. I can get 5-6 sharpening on them and they last pretty well between sharpening. I did not even know harbor freight made their own blade for this mill.
@SONNYREESE
2 жыл бұрын
@@endlessmountainwoodworks4278 Harbor freight does NOT make their own blades!
@donwimberley4772
2 жыл бұрын
Thicker blades on those wheels fail sooner.
@hashim64
5 жыл бұрын
chainsaw use gasoline engine
@endlessmountainwoodworks4278
5 жыл бұрын
What are you talking about? That makes no sense, of course they use gas engines except for the cordless ones and the electric ones.
@burntsider8457
5 жыл бұрын
Must every KZitem video narration open with an unnecessary "so?"
@endlessmountainwoodworks4278
5 жыл бұрын
So it would seem that is how it works. So just watch the video.
@richochett404
4 жыл бұрын
SO YEAH.
@papasteve215
4 жыл бұрын
It seems as though “So” is the beginning of most every sentence of late. It’s kind of irritating to me too.
Пікірлер: 31