It is like watching a surgeon, performing intricate operations... Somehow, it is quite mesmerizing. HAHA! Thank you for sharing this upgrade!
@BigSungHobbies
3 жыл бұрын
Glad you enjoyed it! But my eyes are getting too old for the tiny pieces :(
@scotthudon1228
Жыл бұрын
Excellent vid, made it very easy to do, subscribed & liked.
@BigSungHobbies
Жыл бұрын
Thanks for the sub, and glad that it helped out.
@plukensteinpaint
3 жыл бұрын
Cool video I do notice a difference with turning radius and with climbing. Looking forward to seeing you run some lines.
@BigSungHobbies
3 жыл бұрын
Yes, that's what I am expecting, but will see how much difference it makes when I run the lines.
@teneridertravels
3 жыл бұрын
Great video again! Can't wait so see how it performs on the rocks!
@BigSungHobbies
3 жыл бұрын
14% OD should be incremental, but I can't wait to take it and see how it does.
@andyrichey1192
3 жыл бұрын
Thank you for sharing, this is the next upgrade I want to do. I'll watch for the results, like to see how it performs on the rocks
@BigSungHobbies
3 жыл бұрын
I have done testing on my 1/10 quite extensively. 14% OD will make a bit of difference, but not as much as most folks expect, but it should still result in tighter turn ratio and slight improvement on climbs. Hoping to be able to get out this weekend to test it out.
@glennjthompson332
3 жыл бұрын
Cool teaching and learning and testing.☕👍🏗️🤨 I'm thinking 1/24 scale vs. any truck challenge, maybe 🤔 hmmm... something to think about.😏 nice relaxing review.
@BigSungHobbies
3 жыл бұрын
I run my SCX24 at the same lines that I run for my 1/10 scale to get a feel for it. It actually does fairly well especially on sidehilling, but on certain lines, it's just in a different league. But I do like the idea...something to think it through.
@CactusCrawlersRC
3 жыл бұрын
Thanks for the informative video, I may have to look into these gears!
@BigSungHobbies
3 жыл бұрын
Any time! I am hoping to get out soon and test it out on the rocks. I will report back when I do.
@randall4411
3 жыл бұрын
Very nice demonstration ! I saw it in action and it shows promise .
@BigSungHobbies
3 жыл бұрын
I would have preferred if they underdrive the rear instead of overdrive the front, but I will take it. Especially with stock motor, I need every bit of advantage that I can get. Hoping to be able to get out this weekend to test it out.
@thingsofdoing4507
3 жыл бұрын
What would happen if your rear was jacked up like mine with that on it ? kzitem.info/news/bejne/24asl2tok3d8hXo
@BigSungHobbies
3 жыл бұрын
@rc construction an play The overdrive impacts front wheel speed. The pull of front wheels has bigger impact than push of the rear wheels on climbs. Any reason for jacking up the rear as much as you have set up. More than climbs, I would assume it will hurt on downhills raising the rear CG.
@thingsofdoing4507
3 жыл бұрын
No I just had them laying around , the original shocks provided 0 bounce an bottomed out right off the bat I'm looking at new set all the way around it .
@chujmlrc
3 жыл бұрын
good video and good explained
@BigSungHobbies
3 жыл бұрын
Thank you and glad you liked it.
@islandrc-duke1972
3 жыл бұрын
great upgrade and video
@BigSungHobbies
3 жыл бұрын
Thanks for the visit
@mthobbies5885
3 жыл бұрын
Nice wheels lol!
@BigSungHobbies
3 жыл бұрын
They are working well!
@travispratt6327
6 ай бұрын
There wasn’t any orings with my stock scx24 jlu v3, do they normally come with them on the older models? Just curious if maybe I don’t need them? I’m using an injora overdrive btw.
@BigSungHobbies
6 ай бұрын
At least for me, the 1st release of scx24 seem to come with orings. It's possible that it's not needed. I have mainly used Treal, but I heard good things on Injora as well.
@travispratt6327
6 ай бұрын
@@BigSungHobbies I figured it out, on the jlu v3 at least there’s only one oring on the stock one towards the diff cover. I put one on each end and it was binding. I took the oring towards the driveshaft off and now it all seems good.
@travispratt6327
6 ай бұрын
Does make me curious why though… I wonder if anything else is different, if I get diff covers will they not fit mainly. Guess I’ll just have to find out.
@maurocolombu8524
2 жыл бұрын
Hello guys, I mounted the treal overdrive, putting an O ring on each side of the helical, despite this the movement is not as smooth as it should, it tends to impinge a little. Do I use it like this or do I damage it in the long run? Thanks
@BigSungHobbies
2 жыл бұрын
I didn't notice anything like you are stating after my install. Mine was pretty smooth. It might be a bit more work, but maybe check for any binds?
@maurocolombu8524
2 жыл бұрын
@@BigSungHobbies also my friend have been my same problem
@BigSungHobbies
2 жыл бұрын
Might want to reach out to Treal and see if they can help.
Пікірлер: 33