Dude! Finally someone brings up the filament under the fingernail! I had a piece go all the way to the back of my nail.
@TheEdgeofTech
Жыл бұрын
OUCH!!!!!
@5mmTech
11 ай бұрын
Some things just can't be unread. 😨 sorry that happened to you.
@jmsether
Жыл бұрын
With the cardboard spools, I rip the two sides off and then use the spools that came with the printer as they split in half. There are also spool models built into the printer. This works the best with the AMS so far. You do not need to remove the center cardboard spool as the spool model slips under that.
@WeAreSoBackBros
Жыл бұрын
Thank you!
@Mirrormn
Жыл бұрын
I messed around with all sorts of different rollers and rings for cardboard spools, even tried designing my own, but wasn't happy with any of them. You need rollers to be very snug on the cardboard so that they don't slip when the AMS is back-rolling them, but you also need them to be very narrow because the bottom of the AMS has channels that are only about 10mm wide, and if your rollers rub against those, you'll have retraction errors too. If your cardboard spool is dented or not perfectly rounded or centered, a roller can exacerbate that and make it wobble in the AMS, and if your roller has retaining clips that go over the edge of the cardboard to hold it in place, stuffing it under those clips can create the dents and imperfections you don't want. In the end, it's *much* easier to just wrap a single layer of electrical tape around each edge of a cardboard spool. That gives you great traction, no slippage, no extra width, doesn't need to be carefully adjusted for different brands, and it's faster than printing even the smallest roller. Which should be a lesson to us: not every problem is best solved with a 3D print.
@tkcdac
Жыл бұрын
The least amount of work for simple prints, is just to ditch the AMS and use the back spool holder.
@nategoodwin3329
6 ай бұрын
You are a flipping hero. Thank you.
@marsgizmo
Жыл бұрын
super practical upgrades! great video! 👏😎
@TheEdgeofTech
Жыл бұрын
Thanks man!
@JezzyCrazyTV
Жыл бұрын
XD its new that people dont go to the biggest channel comment but sadly i do btw i bought the bambu lab combo its the best
@dia35
Жыл бұрын
STOP! Now I see I need to order a new printer.... dang it.... Now you've cost me another $1400. Looking forward to my Bambu carbon
@TheEdgeofTech
Жыл бұрын
HAHA Something tells me you were on this path before you saw this video, but I hope you love the printer!
@olafb.2929
Жыл бұрын
My thought, just need to get it financed 😀
@mikebalentine
Жыл бұрын
Have loved mine, amazing device
@jeffj5710
Жыл бұрын
Same here, just ordered mine.
@dia35
Жыл бұрын
@@jeffj5710 you'll love it so much, you may order more. I am in love with mine and amazed every time I use it at the quality and speed it performs.
@pikapalooza7339
Жыл бұрын
Just got mine today! Printing the poop chute as my first real print after the benchy :)
@UncleJessy
Жыл бұрын
Omg this list is amazing. Need to print them all
@TheEdgeofTech
Жыл бұрын
There are already so many more since I made this video as well!
@mindcastpodcast
3 ай бұрын
My X1C will arrive tomorrow - I think I got my list for the first few prints right here. Super useful as it seems, thanks for sharing this collection.
@euroriderdk
Жыл бұрын
The desiccant trays are awesome, so much money saved. Well the rest of the prints I already have before I saw your video, but super big thank you for sharing.
@thelightspeed3d712
Жыл бұрын
I am looking forward to mine... Can't wait actually. Never seen so many positive reviews.
@TheEdgeofTech
Жыл бұрын
I can't wait till you get one!
@3D-Printed-Guy
Жыл бұрын
Love your vids! Please would you keep making videos about the Bambu lab x1 carbon. Like time lapses with it and instruction videos. I would love to see more slicing tutorials with the Bambu slicer. I ordered one for myself recently can’t wait to play with mine!
@TheEdgeofTech
Жыл бұрын
Thank you! Absolutely, I have more videos coming!
@gabrielblock2315
Жыл бұрын
How are you liking it? Worth the $$$?
@markcraig8599
Ай бұрын
I love Saul in the background 🔥🔥 Im gonna make on in marble right now lol
@kevinwatts701
Ай бұрын
Ha ha. The poop shoot was the “ Number Two” build. Good call
@rexdengaming522
Жыл бұрын
got my x1-c ordered it should be here in i say about a month or so. thanks for the info, this will really help me starting out!
@robertthompson3472
2 ай бұрын
Great value! I really appreciate your videos you make for the community 😁 Guess it’s time to order a second X1C!
@colinrand3300
Жыл бұрын
i use wood hardener on the edge of the cardboard spools works great
@unrealbasic1612
Жыл бұрын
Thanks, I can't recommend that splitter however seems like that would be prone to jamming.
@misury
Жыл бұрын
Also, with the poop chute container, maybe modify to angle the bottom to an outside corner, create a through hole, and put it out over a garbage can? Then as the waste comes through it'll empty right to the waste bin. Just a thought. 😁
@TheEdgeofTech
Жыл бұрын
I always thought it would be fun to have a slide attached to the back with magnets and then go down behind the desk to a trash can! Then it would really be a poop shoot!
@AlanTuringWannabe
10 ай бұрын
For the last one with the center tearing out I suggest you design you own or use mesh mixer to fill in the center for stability
@FireDragon3D
Жыл бұрын
These are great upgrades for the Bambulab printers. The spool ring i use is from Blizzard called the Cardboard Spool Ring for Bambu Lab AMS (parametric) - I resized it for Polymaker cardboard spools by 1.5%
@turboboostHoonicow
7 ай бұрын
Nuce upgrades! After the waste box, a ams riser was my 2nd upgrade I did!
@Leynad778
Жыл бұрын
Great stuff you found, thanks👍 I did two smaller sized poop-buckets that can be found on Thingiverse ("bambu lab waste basket"). IMO one of the best mods for the Bambu Lab is a simple cotton-blanket to dampen this beast. First I bought some plywood boards and build a U-shaped enclosure for the sides and top, but the most sound emissions are coming from the back of the printer that needs to be accessible. So I just put a folded blanket on top of the AMS which is just hanging loose over the backside, but huge improvement. Not much improvement in decibel, but it filters this annoying high frequency hall-effect sounds very well and just sounds like common printer with it, not like a factory. IMO Bambu Lab should offer a silencer out of foam for it that fits nicely on the back.
@VigiHunter
Жыл бұрын
Any Problems with heat or airflow?
@Leynad778
Жыл бұрын
@@VigiHunter Nope, the defaults work with all filaments I'm using and don't tinker with temperatures, flowrates etc., but just quality settings like shell- and infill-rates. I've one very cheap TPU-filament that wasn't working well and the default speed-settings with TPU should be reduced anyway.
@VigiHunter
Жыл бұрын
@@Leynad778 Oh I don't means heat while printing but heat problems in the back where the PSU, Mainboard and stuff is. There is quite a large fan back there so I was wondering if a blanket makes it a heat trap 😅
@Leynad778
Жыл бұрын
@@VigiHunter Certainly not during a German Winter.
@lukeqi9265
Жыл бұрын
The revised “magnetic” poop shoot version is absolutely excellent.
@ChimpyChamp
Жыл бұрын
When it comes to the spool cover I would say it's a perfect reason to learn some CAD software, a model like that would two minutes in Fusion360 (hobby licence) + a pair of cheap callipers.
@drCox12
Жыл бұрын
Too much effort. You can just scale it in Bambu Studio.
@ChimpyChamp
Жыл бұрын
@@drCox12 It's effort that's well well worth it, once you have some CAD skills you can unlock the true potential of your printer.
@drCox12
Жыл бұрын
@@ChimpyChamp I agree but you should never overcomplicate things. If there's an easy and reliable way to get the job well done, then take it. Unneccessary complexity is prone to failure which leads to frustration which leads to loss of motivation. Learn step by step: Learning how to scale things in Bambu Lab is a lesson that is also applicable in CAD. Because just scaling the model is exactly what an experienced CAD user would do.
@AndrewAHayes
Жыл бұрын
X1 Carbon Morpheus? Oh by the way, maybe painting the edge of the cardboard spools with nail varnish might make them strong enough to stand upto the AMS.
@chrisgulotta
Жыл бұрын
Great info Jim, I was in need of a poop bucket for my poop chute.
@TheEdgeofTech
Жыл бұрын
😂😂
@gumush
Жыл бұрын
Did you try to feed TPU to AMS hub for printing multiple materials with TPU ? by that way maybe we can use external spool holder -> AMS hub
@mike61704
4 ай бұрын
I just use rubber bands around the cardboard spools. Been pretty great for me.
@NipkowDisk
Жыл бұрын
An excellent collection of useful items for my X1 Carbon which should be arriving next week! Subscribed.
@grahamwood3105
6 ай бұрын
thanks very much for all of your help with all this downloads.good work
@Cereal_Killr
5 ай бұрын
Just throwing this out there. I been running cardboard spools in my AMS for months with zero issues. I had a few rings that I actually tossed in garbage because I was'nt using them. Cool video with alot of cool stuff! I need to make the plate stand for sure!
@fixumdude
Жыл бұрын
Great video. I definitely need to print most of these. Especially the nozzle holder for my stretch goal nozzles.
@TheEdgeofTech
Жыл бұрын
You should! I think it looks sweet to have them displayed too. lol
@BrannonAerospace
5 ай бұрын
For the cardboard spool edges, if you rotated it 90 degrees, it ends up being a lot stronger. But, it’s not very practical, and would require a ton of supports, but it might work…
@theianmce
Жыл бұрын
Really appreciate the summary, thanks!
@omololadopamu4754
Жыл бұрын
I'm glad I came across this 3D printer, hoping to get one soon
@gwchomperz6471
9 ай бұрын
Just got mine! This thing is beautiful
@olafb.2929
Жыл бұрын
Hi Jim, Thanks for the video. It makes me want to have one even more. Please show us more of it and its prints. And, if a human poop chute clogs, it is not good too 😉
@TheEdgeofTech
Жыл бұрын
Haha
@Av8orDave
10 ай бұрын
I've given up on wheels for cardboard and gone back to printing my own full spools. I use Inland filament from microcenter, and even an extra 1/16" is enough to drag on the cover for the AMS. I may try and make my own wheels that don't wrap around the edges of the spool, but just barely extend past the edge.
@mporei
Жыл бұрын
great job man !!! you are very nice !!! keep going community !!!👍👍
@eliasney
7 ай бұрын
Dude.. When you pulled out #5 with the feet to the build plate holder I actually died.
@TheEdgeofTech
7 ай бұрын
😂😆 Glad you were revived to write this comment!
@anupreetkaur4331
Жыл бұрын
This makes using the printer so much better
@3vlogs487
7 ай бұрын
Trick with the desiccant trays. If you have stockpiled filament I never throw the desiccants that come with those away, and I just keep recharging that.
@MATS_MAKERSPACE
Жыл бұрын
Hey Jim great video, only ordered mine on Friday but I'm stoked to be on the list. I love the build surface holder but I think someone needs to do a remix and stagger the slots from left to right so you can grab any of them from the side.
@TheEdgeofTech
Жыл бұрын
Believe you could just rotate the build plates and be able to grab one from each side if you wanted to! Can't wait till you get yours, you're going to love it!
@MATS_MAKERSPACE
Жыл бұрын
@@TheEdgeofTech I've sold evething but the mini to fund it but I'm 100% sure it's money well spent
@thenextlayer
Жыл бұрын
Super high quality video, great work! I'm jealous of your studio - and your X1
@Taliaris
5 ай бұрын
Very helpful! Thank you!!
@Indy69vette
10 ай бұрын
Cool, didn't know Weird AL has a KZitem printing channel
@MacmanPilot
8 ай бұрын
Duramic cardboard spool printed rings work on the poly as well
@reed1sam
11 ай бұрын
Great video, thanks for compiling and sharing the tips
@utdallaz
8 ай бұрын
Thank you!
@KaiusFilius
4 ай бұрын
Regarding the cardboard spools: I found in another video, that you can use the bambu reusable spools on that cardboard spool really well, if you remove the sides. But I haven't tested it yet, because my bambu filament isn't gone.
@NerdyCraftsmith
Жыл бұрын
Can't wait to get my Bambu X1 Carbon
@ottokueng4236
4 ай бұрын
Good informations. But the Y-Splitter does not work. After feeding the filament, it takes some seconds and the filament spools back. After some trials for and back it stops. Sometime it works the first time, sometime after 2,3,4 trials. After disassembling the Splitter filament loadings works without troubles. It seems the time is now to long or the force to low.
@GunnerAl9
3 ай бұрын
Need the new spool holder the AMS to move it from the back of the machine to the side of the machine so you can push the entire case against the wall and not have it out 6 to 8 inches. Great idea. Bamboo should have thought of it.
@fivelights907
Жыл бұрын
This is awesome. Thanks. I guess I’m gonna be printing that bucket PDQ because I bought this for the AMS. Still waiting for it but I’m ok with that.
@justincider8892
9 ай бұрын
I don't know if polymaker changed their spool size since the models were designed, but the standard polymaker spools I have fit/work fine in my AMS without the additional adapters.
@NinjaKiller1022
Жыл бұрын
I’m so glad I’ve come across this 3D printer, and can’t wait to get my hands on it. Also, can you use 3rd party filaments with this printer? It’s not a deal breaker if you can’t.
@ethurial
Жыл бұрын
I have this printer and use third party filaments no issues so far. Used pla, pla+, pla-cf, silk pla, and asa.
@JeremieDeWitt
Жыл бұрын
What type of filament should this be printed in? I'm waiting for mine to come and I want to get some of it done ahead of time.
@robrimell9684
Жыл бұрын
Great video! When I imported the poop bucket stl into my Bambu slicer, I got a message "error - a gcode path goes beyond plate boundaries". Can I safely ignore?
@RumourHasitYT
Жыл бұрын
Same here, if you find a solution let me know thanks
@eyezeeeyeprints9452
Жыл бұрын
Currently, I’m using a drill mounted spool winder that uses a 1/4 Allen key to attach to the drill and had strength to the part. I mount the bambulab spool on my drill and just rewind my filament from polymaker onto the bambulab spools.
@timj1262
10 ай бұрын
Thanks great video
@gieslebt
11 ай бұрын
What kind of reliability or customer service are you guys having with the Bambu machines?
@TheEdgeofTech
11 ай бұрын
Good question! It's been good for me! But they are still growing and they are not perfect. It's much better than most other companies though!
@menchen22
3 ай бұрын
why you dont scale the spool holders?
@RobR386
Жыл бұрын
I re-spool filament from cardboard spools onto used plastic spools
@hanjajsok2872
Ай бұрын
does this work for P1S as well?
@vetulamortem
7 ай бұрын
Coulnt you just scale the spool thingy up a bit so it fits? or use a Master Spool and just trasnfer the Material from Cardboard to Masterspool
@analog1200
27 күн бұрын
Anyone know what brand and color the blue filament is? The one with the clear spool.
@ZhakRyuu
7 ай бұрын
You know you can upscale the spool rings to fit your spools right? I mean its a matter of measuring and inputting the correct diameter in the slicer...
@pufferfish12321
Жыл бұрын
Great vid, thanks heaps. Are there recommended filaments for these upgrades? I only have PLA, wondering if I need a stronger filament to order with the X1C
@AnomieDomine
11 ай бұрын
Anything that gets hot should be at least PETG
@popeizzy2012
7 ай бұрын
Scale up the ring in the slicer to fit
@ktothestank
Жыл бұрын
Holy crap I'm so honored you showed my design on your page!! Thanks so much
@TheEdgeofTech
Жыл бұрын
Awesome! Which one was yours?
@ktothestank
Жыл бұрын
@ktothestank! I'll take your comments and buff them up a bit mine are abs/asa and still working!
@Frostyblaq
Жыл бұрын
Wow I never knew this will happen
@boonjabby
Жыл бұрын
Yes. Filament under the nail is death !
@kevinschilling6813
Жыл бұрын
We need the STEP files to add some thickness to the center hole in the cardboard adapters. That would make the area thicker and less prone to fracture. -OR- you have to do the hoop jumping and go through FreeCAD to convert the STL to a solid model then save it as a STEP file. Then.... Make the corrections/alterations.
@STxFisherman
Жыл бұрын
Great video. Thanks!
@TheEdgeofTech
Жыл бұрын
Glad you liked it! Thanks for watching!
@BobbyHill2973
Жыл бұрын
Great stuff!
@jraiello
Жыл бұрын
Just ordered P1P, but in mean time, decided to download Bambu Slicer and practice on my Ender 3 V2 (the only Creality printer option in version 1.4.1). And to my pleasure, it is fantastic and the quality of print is better than what I was getting with Prusa Slicer OOB and faster. Two Questions: 1) How can I setup my Ender 5 Plus as a new printer in the slicer? 2. Is there a way to directly send the gcode to the Sonic Pad Moonraker/Fluidd interface? Both printers have SonicPads...
@crowguy506
Жыл бұрын
Actually the single piece version of the front lip prints fine in the X1. No need to split it.
@JurassicJenkins
Жыл бұрын
I see what you did there - @1:17 🤣🤣💩 oops - Great vids!
@CelicaRyder69
Жыл бұрын
Polymaker has a file on printables for their spools now
@lesliesavage9229
8 ай бұрын
I was hoping to see something good. For your Polymaker problem you can design your own in CAD, and print them in PETG, which stands up better than PLA. Design your own. I did with my ECO spools, which were smaller than the Overture rings I had.
@hv1461
Жыл бұрын
For the Y splitter, what do you mean 'ams is unbplugged'. I mean, can you go through the steps to make a print from filament in the AMS, to make a print from filament on the back. Thank you.
@canadianoperator
4 ай бұрын
You don’t have to unplug your AMS when using the Y splitter. Just uncheck “Enable AMS” in the slicer and make sure your external spool is selected.
@abcdefg-tj8ij
4 ай бұрын
Yea you're right, Believe it or not when the video was made that option wasn't a thing yet and you did have to unplug the ams
@scotthancock8225
Жыл бұрын
You can recharge packets of desiccant as well
@TheEdgeofTech
Жыл бұрын
True! But I like the idea have it holding more too. Thanks for watching!
@JCthe1maximus
7 ай бұрын
Can you share where you got the Dual-Sided Textured PEl Plate from, the only PEI plate Bambu has is the Gold one, Temu has one similar to the one you have, and amazon has a few without the markings.
@austinmulligan1848
Жыл бұрын
yo - purge lines under the finger nail hurt me like no other possibly could. I could not fathom how much that hurt - way more than one would expect. I got myself pretty good though.... drew blood.
@blatherskyt
8 ай бұрын
Gotta give him props for making the “poop shoot” #2 on his list. 💩
@adekemiadeyemi3610
Жыл бұрын
Woww ... technology has really gone amazing... which i can get this.
@HobbyPrinting
Жыл бұрын
thanks
@dysin_9689
Жыл бұрын
i would say the filament under the finger nail is like giving yourself bamboo shoot torture by accident.
@carstenmller1105
Жыл бұрын
You said that you would put a link in the comments to the files for the print. Can't seem to find them 🙂
@TheEdgeofTech
Жыл бұрын
Take a look at the description of the video, and you'll find all of them!
@bitman05
7 ай бұрын
Tried electrical tape on the edge of an Overture cardboard spool this weekend. 13 hour + print later, all is well.
@richardferraro6886
Жыл бұрын
Thanks, there are several dessicant holders at the cite on Printables. Which did you use?
@OloDeepdelver
Жыл бұрын
Love your videos, please fix your table ! ^^
@LeeroyJenkins94
2 ай бұрын
why dont just use clear or electrician tape over the edge of the cardboard spool ?
@slickman1953
Жыл бұрын
I got your new spool cover with the modded center that won't break
@TheEdgeofTech
Жыл бұрын
Awesome! Where do I find it?!
@slickman1953
Жыл бұрын
@@TheEdgeofTech I modified the one you used.
@RodricWeiland
Жыл бұрын
Great video. I'm intending to put mine into a hacked ikea stand with the printer on top and a large garbage bag underneath. What I'm looking for is a printable poop shute that will allow me to "funnel" the poops out the back of the machine and then down thru a hole in the stand straight into a large gardage bin on the level below the printer. Does such a mod already exist?
@Woodpecked1
Жыл бұрын
I got the P1P 2 Days ago - Woot!!!
@Adam0855
10 ай бұрын
Please advise me if it is worth paying extra for x1 or is it better to take p1s?
@tremaynebaird6839
Жыл бұрын
Ordered this printer already haven't got it yet but currently use almost exclusively polyterra since I have a local distributor for it, is there a problem with using it in the AMS?
@TheEdgeofTech
Жыл бұрын
I have not had too many issues with the AMS at all. Hope you love it when you get it!
@cratervanawesome
Жыл бұрын
Why not just resize the small edge covers to fit before printing? It should be pretty easy math to remove or add how ever many mm of diameter you need.
@snugglebuns6969
5 ай бұрын
Can u use the printed splitter to load and use TPU? asking for a friend.. TIA
Пікірлер: 223