Thanks for sharing. -watching from the Philippines.
@kanagarajkanagaraj6775
Жыл бұрын
I love your lecture, very helpful Sir.
@shokatraja1832
2 жыл бұрын
MashALLAH yr really dua ha apke lia
@josephmasvokisi7745
Жыл бұрын
I like your teaching you are highly knowledgeable
@ForensicCats
2 жыл бұрын
Perhaps rule number 11, we should spray galvanized over all outer reinforcement, including stirrups or at least etch and nutrialize metal to point of ph concrete pH will not react as much... Then we could add number 12, use a coating to protect exposed columns from water intrusion. Keep up your good work, I have posting on this for years now...
@TheLazyGuyWay
2 жыл бұрын
Nothing not graded and recommended in engineering should be sprayed as he could alter chemicals contained in concrete mix. Minimum rebars cover is based on building area too. To prevent water intrusion especially in salted air area, we would use a different type of cement like type 2 portland ciment with c3a < 8% or even a type 5 portland ciment with c3a < 5% which is better.
@bossingsarmento8989
3 жыл бұрын
I learned a lot from your video, good boy. Thank you sir
@mamadoudiop5462
2 жыл бұрын
Great video, very academic. Thank you from Senegal
@VicTv1992
6 ай бұрын
Thank you sir, for sharing your knowledge. I am learning from your lectures.God bless .❤
@zainalabidin6390
3 жыл бұрын
Alaikumussalam brother...thanks for your video.. Very important for me..i like
@PBS-nm1uu
Жыл бұрын
best video i have seen so far, thanks
@prafulsoni1095
3 жыл бұрын
Very useful RC column design rules.
@REG3305
3 жыл бұрын
TY sir! All the best!
@osmanyussuf7069
Жыл бұрын
Masha Allah thanks
@hawk61192
3 жыл бұрын
Very informative video brother. Very well explained.
@MustaphaGoni-ru3op
8 ай бұрын
Masha allah i really appreciate you Sir
@ayuubmohamedisxaaq2859
4 жыл бұрын
God bless you Great teacher
@hanadnor2457
4 жыл бұрын
Maasha Allah. Thanks brother
@civilvibes8036
3 жыл бұрын
thank you sir wonderful explanation keep it up
@JahidulIslam-bf5qw
2 жыл бұрын
Thank you sir, i am from Bangladesh
@ziauddin7948
3 жыл бұрын
Good civil engineering rules of column construction #
@adityaadityanarayana6862
4 жыл бұрын
Good message brother 👍
@yabagabaduza
3 жыл бұрын
Thank you for the education, I have a plot size 60 × 25 ft, I. Want to make one big shop without middle columns and to construct four storey residential houses on top, kindly advise how will I design the columns and beams. Thank you.
@ManneLearningAcademy
3 жыл бұрын
Nice presentation there sir. i learned a lot. Keep it up. More videos sir.
@REANDESIGNSTRUCTURE
Жыл бұрын
Thanks for share knowlegde.
@booksourexistence2153
4 жыл бұрын
Thanks a million sirji
@ahsanbinalrahmanfromairara9868
4 жыл бұрын
Thanks Sir Ji Allah Bless You Sir Ji
@bayisabiri2450
4 жыл бұрын
Thank you, that's good
@romycruz4498
4 жыл бұрын
Thanks again- from-Phils.
@DefinitelyNotHawks
3 жыл бұрын
00000000000000000000000000000000
@phyohtetkoko929
Жыл бұрын
Thanks For Teaching SIr
@cyrilthomasthomas6714
Жыл бұрын
Super sir
@nizamali7027
3 ай бұрын
Nice teaching
@syedshabirgilani9944
3 жыл бұрын
Thanks . What should be the reinforcement ratio i;e steel qty.
@justinekihoro5152
3 жыл бұрын
I have learned a lot about building from u
@kefelegntemesgen7958
3 жыл бұрын
Good explanation!
@P99665
Жыл бұрын
Useful info thanks
@mjazz9017
2 жыл бұрын
Very informative 👍👍👍
@cliffriifiu1586
3 жыл бұрын
I love your lecture, very helpful hope to get more information from you sir
@bsudheer05
2 жыл бұрын
Good explanation...
@joshuabautista9519
3 жыл бұрын
Thank you! So useful
@sekarramaswamy5111
2 жыл бұрын
It is not readable pl due to light ink...
@muhammedtijani2308
Жыл бұрын
Peace to you my Honurable Engr. Sir, thank you sir.
@anthonymarafi8160
Жыл бұрын
Thank you for sharing. 🙂👍
@homendrapandey5708
4 жыл бұрын
thank you very much,
@aadil8715
2 жыл бұрын
I was laughing the whole time, the accent , the spellings,hahhahah any way good one.
@nagaraj5338
2 жыл бұрын
Very nice explanation and fabulous
@abdumohammed6880
3 жыл бұрын
Hey sir ..is that safe if the depth of the beam less than that of the depth
@abdimajiddek7782
Жыл бұрын
Thanks so much teacher
@mahaboobsubhani6758
2 жыл бұрын
Sir What happensin colmn if concrete cover more than 25mm in rectangular column
@dulhapur
2 жыл бұрын
For finding A zone and B zone in coloumn only two floor beams are considered,is not lintel tie beam required to considered?
@ainunjariyaazad9179
4 жыл бұрын
Thanks sir Please upload to how prepare bar bending schedule ?~~
@ashokreddy5537
3 жыл бұрын
ì
@simranratnani5923
3 жыл бұрын
please make video on distance between two columns,grids and size of columns
@constructionmaster2642
3 жыл бұрын
How I know what is steel bar size is required for different colums for load bearing
@dinakadi6609
3 жыл бұрын
Thank you very much
@sawjulianku8136
8 ай бұрын
Thanks, I have been studying yr video n like it. Only a bit difficult in following yr accent.
@CR-io3xw
3 жыл бұрын
Very interested your class sir
@willfordnongspung6238
3 жыл бұрын
Great sir but we hardly understand the third and fourth rules any way your explanation are of great help
@jnyanendrakumarjena4354
4 жыл бұрын
Thanks.
@bebotepuknot2631
4 жыл бұрын
Rectangular column can be use 6 longotudinal bar?
@charlesgregory7469
Жыл бұрын
Is there a height to cross section area ratio in columns?
@iamphyize
3 жыл бұрын
nice one
@debendrabehera7626
8 ай бұрын
Sir, Can we construct 2 storey bulding with 4 nos. of 12mm rods in a column ?
@DeejayPapi
2 жыл бұрын
🙏🏽❤amazing
@manojkumar-qu8ml
3 жыл бұрын
I have planned to construct two separate rooms like 20*10 ( ground floor with 10*14 room size at first floor) & 22.5*10 (only ground floor) . My engineer suggested RCC is as follows. Pls tell it correct or not. Basement level of 22.5*10 is 2 feet less than 20*10 room 1. For 20*10 - 6 columns of 12*4 with 8mm stirr up of 7 inch c/c - four at each corner and remaining two at spacing of 8 feet at one end and 11 ft at other end. Plinth beam with 1.5 feet height and 9*9 (l*b). Ceiling height is 10 feet. Planned tie beam at below windows (2.5 feet) and lintel (7 feet) of 6 inch rcc 2. For 22.5*10 - 6 columns of 12*4 with 8mm stirr up of 7 inch c/c - four at each corner and remaining two at spacing of 10 feet at one end and 10 ft at other end. Plinth beam with 1 feet height and 9*9 (l*b). Ceiling height is 12 feet. Planned tie beam at below windows (4 feet) and lintel ( 8 feet) with 6 inch rcc And join the both room in ceiling and both room in 90 degree position to each other
@bijayalaxmipant9940
3 жыл бұрын
Is it possible to build a building in a single column?
@uzmaonline4844
3 жыл бұрын
Nice bhai
@amitgehalot125
3 жыл бұрын
Sir can we change orientation of one column at first floor
@gopalkamble1263
3 жыл бұрын
Ties spacing in IS code maximum 300 mm
@BigBuck6244
4 жыл бұрын
Plz discuss Acceptance criteria of concrete as per Britesh Standard
@BigBuck6244
4 жыл бұрын
And Concrete Control Charts Discussed
@gangmeiaphun5026
Ай бұрын
why extra steel/rod are putting below in the L/2 portion of beam? please
@ChoooooXiS
3 жыл бұрын
Sir, what is the required column and wall footing for 2-storey 5x5 residential house? Thanks.
@ragibkhan2323
4 жыл бұрын
👍🏼
@luckynoob3328
10 ай бұрын
Thank you sir
@gayanpradeepkumara5557
4 жыл бұрын
Brother What happens if concrete cover less than 25mm...... ?
@ayoubenaciri
3 жыл бұрын
👍👍👍
@SurajChauhan-qh7bh
3 жыл бұрын
THANKS SIR
@munaseid2765
2 жыл бұрын
I didn't understand the first two rule how do we know when designing where the axial load would be to choose either square or rectangular column?
@srinivasandk9680
3 жыл бұрын
excelant sir but more advertisments coming in short times . thank u.
@jeevanchaudhary7222
3 жыл бұрын
how we can know column is taking Axial or Eccentric load
@ZaiidRaza
4 жыл бұрын
Sir apka wo Shadi ka coat nhi pehne apne?
@mahaboobsubhani6758
2 жыл бұрын
Is clear cover not same around tie of column sir......u said 25 mm from top and bottom and >15 mm from side:....shall we take same or different..
@MuhammadAzam-oi2xg
3 жыл бұрын
Sir if load coming on 3 then size of coloum?
@MuhammadAfzal-ok1ip
3 жыл бұрын
What is pullers with 6 bars use like a shop covered area is 984 sq ft 1floor and 2 floor is 835+ 835 sq fts
@nelsleons2931
3 жыл бұрын
How about determining the axial load for column sizing?
@davidcivil1651
3 жыл бұрын
Calc the load transferring from slab to beams and from beams to column.
@rajeshraj8106
4 жыл бұрын
Sir. How would we know the column is axial r eccentric?
@sagarSooriya4542
2 жыл бұрын
sir,in your 5th rule you said about concrete cover. it means clear cover right. you are saying about effective cover, isnt it?. because effective cover is between top steel center to top edge distance. so concrete cover and effective cover same?
@foodmates1994
2 жыл бұрын
Hi sir plz reply my question,my house only G[G+0], span between 2 columns length 19 feet ,wedth 14 feet , size of colum 9/15 with 6 bars of 16mm rectangler column, all house walls 9 “wall. And first we make walls before slab it is safe or not ? Plz reply
@devarushidevarushi1810
2 жыл бұрын
Thanks
@ragibkhan2323
4 жыл бұрын
Sr can you explain about Circular column.
@AtomicHermit
2 жыл бұрын
In 7 and 8 you may mean vertical rather than longitudinal?
@pattaharsha2220
4 жыл бұрын
Where the laplength should be provided in column.....?
@wefindwaystodothat6431
2 жыл бұрын
what is minimum Beam size if 5x5 meter support column residential Building.
@Gamebd1
3 жыл бұрын
tnk u
@user-lx4qm1gy7g
10 ай бұрын
How about 9meters span beam what should be the coulumn n beam
@indianarchitecture
3 жыл бұрын
♥️♥️♥️
@EngineeringandConstruction
Жыл бұрын
What about footing design if a soil is black cotton?
@gerardoatutubo4759
4 жыл бұрын
Sir, size of column plz....if G, G+1, or G+2 residential 4m span. Tnx.
@mackybishmac8559
2 жыл бұрын
Please sir I would like to build a two storehouse only and coloum can this be done
@harishXO
4 жыл бұрын
Sir how would we know that load is on centre or eccentric?
@veerababuakula1344
4 жыл бұрын
Eccentric means the load is not passing through the centre and it passes at some distance from the centre
@kiyoponnn
3 жыл бұрын
@@veerababuakula1344 Moron.
@adhivamshi2154
2 жыл бұрын
How to do cost estimation for Foundations
@kartikshekhar940
4 жыл бұрын
Sir your video is very informative. 1. Pl suggest the column width for a 25 ft X 44 ft plot (2 Storey Building) ? Is 12 “ X 12 “ enough with 8 Nos 12 mm bars ? 2.Also pl suggest maximum spacing between 2 columns in the above mentioned structure?
@tslunzou6393
2 жыл бұрын
max spacing of columns should not be more than 5.5 metres
Пікірлер: 161