✅ HOW TO SUPPORT MY CHANNEL SUBSCRIBE : kzitem.info JOIN my Patreon community: patreon.com/MWAWoodworks GET project plans: bit.ly/download-project-plans ✅ TOOLS AND SUPPLIES IN THIS VIDEO: ►Spectape Two Sided Tape - amzn.to/3IxTMma ►True Position Cabinet Hardware Jig - amzn.to/3KDHjjK ►Kreg Shelf Pin Jig (new model) - amzn.to/3kwugpG ►Bangood Pocket Hole Jig - amzn.to/3Zonuki ►Kreg Pocket Hole Jig (new model) - amzn.to/41qvovu ►Castle TSM 12 Pocket Hole Cutter - castleusa.com/products/tsm-12-benchtop-pocket-cutter-machine.html ►Festool LR32 System - amzn.to/3KxTmPw *As an Amazon Associate I earn from qualifying purchases
@AshOnTop23
Жыл бұрын
Thanks, I picked up a bunch of tips! For laying out drawer slides, plywood is a great idea. But if you start from the lowest slide and cut pieces to stack up to all your slide install lines you can use the same pieces of plywood to lay out the drawer slides in more than one cabinet instead of cutting up a piece of plywood for each one. If you start from the top and cut it down to size as you go you lose the width of the kerf and can't reuse. Even if you are only making one, you can still do all the slides on one side at the same time instead of switching back and forth and there's no running to the saw every few minutes. It'll save a lot of time- efficiency in all things comes from doing repetitive tasks as many times as possible without moving.
@t.e.1189
7 ай бұрын
I just watched 3 or 4 videos and have to say I really enjoy like how you keep things moving along. You share a lot of info and a relatively short span of time. No fluff, dumb, dry humor that is painful to watch or loud obnoxious music playing over your speaking. Thank you and you've got another subscriber.
@Marcus_Caius
7 ай бұрын
I agree with you 100%. Too many youtubers THINK they are funny making their videos less appealing.
@Chuck.S.
Жыл бұрын
Golden Rule - There is no substitute for experience.
@MWAWoodworks
Жыл бұрын
For sure!
@gregchristineharris7207
Жыл бұрын
That’s was a bunch of good info!
@frankdomburg3971
Жыл бұрын
Would like to add, no fear. Cut, and then decide to proceed with what you got or to try again.
@saberxebeck
Жыл бұрын
And experience is just how many times somones gone wrong and fixed it. So someone much better than you has already solved the problem. You just need to find the internet article.
@ossef9712
9 ай бұрын
That’s assuming you have it on your first attempt…I’d counter by saying “planning & prep” is the golden rule.
@Feller1853
7 ай бұрын
At 70 years old I am planning to redo our 50 year old kitchen and my intention is to build the cabinets myself. I really enjoy your videos, very informative and educational. I do though have a question. In the background of many scenes of this video there is a three door wall cabinet. The doors have a wider gap between the center and right door than the center and left door. Is there a reason for this?
@williamkamp9162
9 ай бұрын
Just another great video that makes me feel like I can build my own cabinets
@cuebj
Жыл бұрын
Superb video. Not a lot new to me bit all in one place - materials, tools, methods. Clear, well-spoken. And I can translate to millimetres in my head (UK, started from age 4 with £, shillings, pence, ha'pennies and miles, yards, feet, inches, and tons, cwt, pounds, ounces, and gallons, quarts and UK pints at 20 floz. Age 15, we went decimal and did science to university). It's a useful and fun discipline to beat folk with calculators!
@Grimster72
5 ай бұрын
I feel like that cat that ate the canary, a (not so local) cabinet shop was WAY over stock on 1/2" UV Birch and I bought 30 sheets for $22 a sheet, per SHEET (yes 4x8). I'm gonna feel like a monster when I use that for underlayment.
@BeauChampion
Жыл бұрын
Fantastic video. Definitely one of the best cabinet Q&A type videos I've seen. I love that in several sections you offered an affordable jig/tool and an upgrade option, especially for things like pocket holes and shelf pins where the affordable option remains useful even after you upgrade.
@MWAWoodworks
Жыл бұрын
Thanks for your support!
@NWGR
Жыл бұрын
Here's something I've been thinking about: I have some kitchen cabinets I'm building that will all be drawer units. In this instance, do the bottoms need to be solid panels, or will stretchers like those typically used for the tops be sufficient? It's a span of three 24" cabinet boxes that will be screwed together. I could save some money by using stretchers instead of solid panels.
@talltreecustoms
3 ай бұрын
love building with prefinished c2 maple plywood :). Local distributor has it for $105 / sheet, and it is definitely my go to when building new cabinets for customers don't care what the material is.
@mauricecooper9016
9 ай бұрын
I did not know that pre finished plywood was still paintable. I have been looking for pre finished on one side for my kitchen because i planned on painting them. You just saved me a huge headache!
@MWAWoodworks
9 ай бұрын
Yes if you scuff sand it and prime it you can definitely paint it.
@garyburnett7378
Жыл бұрын
I’ve been making cabinets for 30+ years and I learned a ton from this video. Thank you.
@AscDrew
8 ай бұрын
How is that poss?
@childofatom95
Жыл бұрын
06:00 I'm a drummer, and I also happen to be Italian. We use the metric system here so I was spacing out while you were laying out (eheh) the standard measures... But man those drums in the background music sound amazing! Aaand nice tips too lol
@charlesschmitt9555
Жыл бұрын
I really enjoy your videos. I bought your plans for the drill charging station, and it has really improved my shop organization. You inspired an Ephinay when you explained why you use pre-finished plywood. I find myself not wanting to finish shop projects, but it makes so much more sense to use pre-finished plywood because you don't have to sand or set up to spray the project. Thank you for your videos. They are very helpful for me.
@MWAWoodworks
Жыл бұрын
Love it!
@jeffshackleford3152
Жыл бұрын
Just make friends with some painters. If you have good trade skills, there is a whole underground economy of labor trades amongst the working man.
@renanburato3623
11 ай бұрын
I would suggest putting the wood measurements in millimeters (MM) to make things easier, but anyway, very cool video!
@MWAWoodworks
11 ай бұрын
Thank you. One day I will make some cabinets in MM but today it's too expensive to design in both measurements.
@johnjensen5540
Жыл бұрын
I love your no BS and high info style of teaching/explaining. Nice video, please keep it up!
@MWAWoodworks
Жыл бұрын
Thanks for your support John!
@yougolook
10 ай бұрын
Wow I just found your channel …. You not only build beautiful cabinets but you are very professional in the area of video production…. I am interested in starting a channel on woodworking and would love to get a chance to speak more with you… Thanks for the great tips… I just finished adding 10 drawers to my shop today…
@3weight
5 ай бұрын
Yeah that Rockler drawer slide jig is the biggest piece of junk I’ve ever bought, fully 3/16” off 90 degrees from the face over its length. I had it for too long before trying it and couldn’t return it, it’s the only tool I’ve ever just tossed in the garbage unused. The method you show is by far the best, even though I don’t really have that much scrap hat large sitting around 🙂
@GK-qz3cm
Жыл бұрын
Excellent video! I am just starting on my first cabinet building project. First run is a cabinet to mount my drill press. Then on to replacing all my kitchen cabinets. Not certain if I am crazy for tackling this or nor.
@MWAWoodworks
Жыл бұрын
Hahaha no way to learn like jumping in!
@sethhamilton5824
10 ай бұрын
One of the first tools I bought after my table saw was the castle. The pockets don’t look like amateur hour, they look machined and precise (which they are).
@MWAWoodworks
10 ай бұрын
🙌
@danielrybin2006
Жыл бұрын
I think one of the biggest things for me was realizing the OUTSIDE dimensions of a face frame carcass don’t matter. It’s the face frame itself, and the INTERIOR dimensions (stretchers, bottom/tops) that are most important to get right. And bc of the variability of plywood thickness, the exterior carcass size doesn’t matter
@MWAWoodworks
Жыл бұрын
Yeah for sure in order to get your drawers sized right!
@thewoodshop69
Жыл бұрын
Very well explained. Got set up on the festool system about a year ago. Was a learning curve but once you figure it out it's awesome.
@MWAWoodworks
Жыл бұрын
I agree. Once it's set up right it's a blast to use
@buzzpatch2294
4 ай бұрын
saved this vid -to review as i did project great tips that i used. and i really liked the way you presented the whole process.
@falconiguana
Жыл бұрын
Thanks for the video!
@MWAWoodworks
Жыл бұрын
You're welcome!
@andrewwhewall
Жыл бұрын
Really, really useful video. I'm just about to embark on my most ambitious woodwork job ever - building my own kitchen. Your video is a great help.
@ftnirish74
Жыл бұрын
Hands down, one of the most informative Q&A video. Thx
@AntiViGames
Жыл бұрын
For the second tip where you use a scrap piece of plywood to set your drawer slides at the proper height you might as well make a little jig for it that you can reuse over and over again plus you'll be able to add a 90 degree on the bottom to support it so it doesn't fall over. it would essentially work a lot like your drawer handle jig.
@MWAWoodworks
Жыл бұрын
Good idea!
@dougtilaran3496
Жыл бұрын
The "J" word is no longer permitted. That's now referred to as a fixture ;-)
@jeffshackleford3152
Жыл бұрын
@@dougtilaran3496 jig?
@dougtilaran3496
Жыл бұрын
@@jeffshackleford3152 No longer permitted " fixture is PC
@jklong03
Жыл бұрын
@@dougtilaran3496 You know where you can put your PC advice? Up ............
@JJJere
11 ай бұрын
You're a good teacher.
@ACDC267
6 ай бұрын
Right!?
@capemaster123
Жыл бұрын
Wow this whole time I assumed painting on pre finished wouldn't yield the best results. Thanks for making that clear! You're the best man, wishing you continued success on your channel! 👊
@MWAWoodworks
Жыл бұрын
Thanks Charles!
@alkemis
Жыл бұрын
UV Coated is your second guess. UV light is used to cure the coating making it more durable and scratch resistant. Great videos keep them coming.
@TheAaronReynolds
7 ай бұрын
I didn’t know you were in the Nashville area! We are in MJ. Found your tips to be super helpful! Thanks for another great video 👍
@MWAWoodworks
7 ай бұрын
I am indeed!
@JoeWoodMakeThat
9 ай бұрын
Thanks for the video… i woodwork but haven’t made kitchen grade cabinets. Appreciate the full breakdown 🫡
@meperson
Жыл бұрын
This is very useful video and really appreciate your animations showing various size calculations. Thank you!
@MWAWoodworks
Жыл бұрын
Ha thanks!
@davidcurtis5398
Жыл бұрын
Love pocket holes for construction. My Kreg jig is made completely of aircraft aluminum with steal inserts. it is one of the first ones that the company made and is about 30 years old and it is still being used although I have a newer jig now. I like the box you have for the jig. Thanks for this video...
@johnberry2877
Жыл бұрын
The right tools make a tremendous difference!
@knightclan4
Жыл бұрын
I love prefinshed plywood
@MWAWoodworks
Жыл бұрын
Yeah it's a game changer
@georgemora7744
9 ай бұрын
I love that kreg box! Nice an simple
@steppedon
Жыл бұрын
This video is so timely. Almost pulled out the domino for a built in bar that I'm doing, but will go with pocket holes instead.
@MWAWoodworks
Жыл бұрын
Pocket holes and cabinets go together!
@adgieem1
11 ай бұрын
Great video. I would love to watch you install some hinges.
@MrMan-jf8yi
Жыл бұрын
UVlight is used during the finishing process so the plywood can be stacked at the end of the finishing process
@MWAWoodworks
Жыл бұрын
Yeah I've since done some research of Columbia Forrest Products process and learned the same thing
@Fishing-gs9ku
Жыл бұрын
“One day you might use it for something” hahahaha ok I’m not the only one
@TedAlexander24
Жыл бұрын
Great video! Simplifying some seemingly complex issues.
@MWAWoodworks
Жыл бұрын
Thanks Ted! Glad to help out.
@johnford7847
6 ай бұрын
A lot of very useful information. Thank you very much for sharing.
@Mr.GucciClass1A
Жыл бұрын
Awesome!!! I also use your cabinet plans I purchased a while ago as a great go to reference when I work build cabinets myself. 👍🏽 Thanks for your content and instructional style.
@MWAWoodworks
Жыл бұрын
👊
@robertridenour4308
Жыл бұрын
Enjoyed the video. Thank you! One ? - I've recently tried pocket hole assembly of drawer boxes and can't find a screw head that works with 1/2" Baltic without protruding past the primary surface. Is that why you are using 5/8?
@MWAWoodworks
Жыл бұрын
Yeah pocket screws aren't really a good option for 1/2. You can do it but you need a special adapter
@YoAug62
8 ай бұрын
I'm a newbie wanting to build my own kitchen cabinets and my preference is to use a separate kick plate. If I'm using a separate kick plate, do I subtract the height of the kick plate from the standard height of the base kitchen cabinet? For example, if the height of my kick plate is 3.5 inches, the height of my base cabinet will be 31 inches (34.5 inches - 3.5 inches). Is this correct?
@brettburriss7522
Жыл бұрын
Thanks Mate, excellent video - very helpful. *highfive* from Australia
@MWAWoodworks
Жыл бұрын
Thank you sir!
@craigfehr411
Жыл бұрын
Excellent video. Love your content. One question I have is how wide do you make your drawers, particularly when using side mount slides. Do you subtract just the width of the slides from the carcass?
@MWAWoodworks
Жыл бұрын
Correct. For full extension side mounts, subtract 1 inch from the width of the opening.
@allsurf
Жыл бұрын
Was considering using one side finished plywood. Do you sand the finish and primer before painting the pre finished or just prime and paint without sanding?
@MWAWoodworks
Жыл бұрын
prime and paint without sanding
@fatcamp907
10 ай бұрын
UV Plywood uses a UV resistant coating to protect it from fading.
@mitchellgarcia3532
9 ай бұрын
Outstanding presentation of information thank you!
@Ratheepan1122
3 ай бұрын
Could you make a video on table saw setup please
@ryanchaffee7243
Жыл бұрын
Depending on which true position jig they have a shelf pin jig included also
@MWAWoodworks
Жыл бұрын
Thats true they do have an attachment for shelf pins!
@T_Jonesy
Жыл бұрын
Fantastic video. Really breaks things down into manageable, easy to understand bites.
@mrtrader4628
11 ай бұрын
Very good but you did not cover undermount for slides spacing versus side mount spacing four box sizes of drawers
@joeglorytv
9 ай бұрын
Awesome video very helpful thank you
@MWAWoodworks
9 ай бұрын
Thanks!
@JAT922
Жыл бұрын
Great tutorial. Whats your opinion on plywood thickness for face frame cabinets. 1/2 or 3/4 for sides and 1/4 or 1/2 for the back?
@MWAWoodworks
Жыл бұрын
I use 3/4 for the carcass and 1/4 for the back
@micahfort5439
Жыл бұрын
A good compromise for the castle pocket hole machine is the Kreg Foreman. Very fast and easy to use for around $300.
@MWAWoodworks
Жыл бұрын
Yeah you just have to be careful with bit breakage. A big issue with the foreman because it still uses the same drill bit as a regular kreg jig but not really designed for that much efficiency like the Castle machines which use routers instead.
@40redfox40
6 ай бұрын
This was Fantastic info! Thank u for taking the time.
@eduardodomiciano6401
Жыл бұрын
Great video! Very informative! 👊🏼
@MWAWoodworks
Жыл бұрын
Thanks!
@billday8501
Жыл бұрын
Hope you don’t mind hearing it again, but, THANKS! Great info and great use of my last 17:31 plus another 20 or so replaying, browsing linked products/merch, etc. 👍🏻👍🏻
@seanmichael5751
9 ай бұрын
very nicely done vid. thank you. one question about drilling shelf pin holes with a router.... what bits are you using? i know end mills are horrible for drilling and ive burnt up quite a few that way on the cnc.
@MWAWoodworks
9 ай бұрын
The LR 32 system comes with it's own bits that are a hybrid of a drill bit and router bit to make clean holes on both sides of the cut
@SmithJonny45
Жыл бұрын
Excellent video. Thank you!
@MWAWoodworks
Жыл бұрын
You're welcome 😊
@SynergyAVE
Жыл бұрын
What brand of side mount soft close drawer slides do you use? For the most part, I have had bad luck with all that I have used. I realize a precise installation is key to them, but still...
@MWAWoodworks
Жыл бұрын
I don't have a brand that I favor on side mounts. I get whatever home depot or Amazon sells. I find all side mount slides to be virtually the same.
@denislemos4398
9 ай бұрын
So many good tips. Thank you
@Marcus_Caius
7 ай бұрын
Question about the pocket hole jig from Enjoywood. Do the kreg drilling bits fit on it or that one use metric size bits?
@MWAWoodworks
7 ай бұрын
It uses the same size bits and same size screws
@thomasemberson8021
Жыл бұрын
Funny for aligning drawer slides on the sides of the cabinets I've been using the same approach for year. But with the price of plywood, I've gone to keeping smaller scraps, and join joining them together with Domino for new cabinets.
@MCsCreations
Жыл бұрын
Lots of excellent tips there, Matt! Thanks a bunch! 😃 Stay safe there with your family! 🖖😊
@MWAWoodworks
Жыл бұрын
Thank you!
@BRTardiff
9 ай бұрын
Are you still using Nashville plywood since they moved?
@woodybrown1627
Жыл бұрын
Do i have to put a base on the cabnet
@MWAWoodworks
Жыл бұрын
What do you mean like a toe kick?
@woodybrown1627
Жыл бұрын
Yes
@MWAWoodworks
Жыл бұрын
You can also build a separate base and set the cabinets on them
@CisnerosShop
Жыл бұрын
How do you determine the size of the face frame openings for drawers? Is it standardized, custom or both?
@MWAWoodworks
Жыл бұрын
I usually make my face frames with a 1/4" or 1/8" overhang on the inside of the cabinet
@DIYwithDennis
Жыл бұрын
Great information! Thanks for sharing!
@MWAWoodworks
Жыл бұрын
You're welcome Dennis!
@SamWanamaker1
Жыл бұрын
What kind of router bit do you use when doing shelf pin holes?
@MWAWoodworks
Жыл бұрын
I use the ones that come with the festool lr32 system. 5mm
@danielakerman8241
11 ай бұрын
You missed one: Attaching cabinet doors. How do you attach cabinet doors and ensure they are straight, they close well and are spaced correctly?
@WoodworkingWarrior
Жыл бұрын
Nashville, TN..... I'm just up the road in Clarksville.
@MWAWoodworks
Жыл бұрын
👋
@CathyEbs
10 ай бұрын
Some great tips. I can't access your plans on your website as according to my antivirus software your website has malware. Just thought you should know so you could fix it.
@MWAWoodworks
10 ай бұрын
Thanks for the notice, but it doesn't have any malware! You can also go to shopmwawoodworks.com and buy them there as well.
@Tdog500
9 ай бұрын
Thanks for all the great info!
@krisslick007
Жыл бұрын
Thanks for the videos. I really enjoy your style of teaching! I have purchased the plans and am in the process of building some cabinets for my shop. I see that you used prefinished plywood for your boxes. Do you use any kind of finish on the face frames and drawers on your shop furniture? If I am using unfinished plywood and will be using Hickory for the frame, should I be using a finish? or is it not necessary since it is "just shop" furniture? Thanks again!
@MWAWoodworks
Жыл бұрын
I think you can do whatever you want. I like mine unfinished for my shop.
@LuisSanchez-wf9zw
Жыл бұрын
Do you have a video on how you paint these with the Sherwin Williams paint products? And do you seal the edges of the face to face frames on the doors or leave them clean? And are the faces pre-finished 1/4” ply too?
@MWAWoodworks
Жыл бұрын
I do have a video on my painting process
@ajaykapadia6262
10 ай бұрын
Can you leave a link for the video you have on how you paint pre finished plywood? I am curious if you need to sand first.
@therelaxingwoodshop7495
Жыл бұрын
The cabinet man is back
@MWAWoodworks
Жыл бұрын
🙌👊
@mobareini4572
Жыл бұрын
Super Video, Greetings from Vienna.
@johntiefel4248
Жыл бұрын
This video solves a lot of problems and will save me sooo much time in building cabinets. Building them upside down is a simple solution to a difficult procedure. why in the hell didn't think of that. If we really want to punish Putin we make him install drawer glides for eternity without watching this video!!!!. Thanks a Bunch young man.
@MWAWoodworks
Жыл бұрын
😀
@tomcotter2714
11 ай бұрын
Thanks for explaining things in a clear, concise way.
@zachc1
Жыл бұрын
Great video, thanks man
@MWAWoodworks
Жыл бұрын
Thank you Zach!
@sandmandave2008
Жыл бұрын
I watched your cabinet video (fantastic) and am using that info to build my miter saw bench. This video answered some questions but I still have one more. Concerning the 1/4" plywood back panel, Is it for squaring the cabinet or just so it looks finished from the inside? I'm thinking it isn't necessary for a shop miter saw station when all the cabinets will have drawers so the back of the cabinet isn't visible.
@MWAWoodworks
Жыл бұрын
You don't have to include the 1/4 backs, just the nailers and stretchers are important for structure
@sandmandave2008
Жыл бұрын
@@MWAWoodworks awesome, thanks. I can save my extra sheet of quarter inch birch ply for more drawer bottoms and french cleat holders. I really appreciate the quick response since I'm starting to cut the carcasses tomorrow morning. You're the best.
@DaveRCol
Жыл бұрын
Great info! Thanks
@MWAWoodworks
Жыл бұрын
Thank you!
@justinb2359
Жыл бұрын
I do have one quick question, how do you determine the size of your door fronts? I know it can depend on the amount of doors or drawers, but say for instance I want a 30" wide cabinet with 2 pull out drawers. How do I determine the size of my drawer fronts? Thanks in advance!
@MWAWoodworks
Жыл бұрын
Determine how much reveal you want around the edges of the drawer fronts to the face frame and then determine how much gap you want between the drawer fronts. 1/8" is a good number but this is 100% preference, there's no "rule"
@justinb2359
Жыл бұрын
@@MWAWoodworks Thank you!
@PeterFreese
Жыл бұрын
Is it better to make your face frame flush with the inside of the cabinet for side-mount drawer slides, or to use an overhang and filler strips?
@MWAWoodworks
Жыл бұрын
It's all personal preference, the look you want.
@donalddparker
Жыл бұрын
Great advice! Exactly what I used to use to coach new programmers and engineers in CPU design. Keep it up!
@wonkywoody
Жыл бұрын
Excellent video. I sure wish I'd seen it 3 months ago:-) BTW, how do you record audio in your shop with no echo? I can't seem to find the right formula.
@silverfox8801
Жыл бұрын
That ply would be over $150 per sheet here in the uk!
@MWAWoodworks
Жыл бұрын
YIKES!
@AngieWilliamsDesigns
Жыл бұрын
Helpful video. Thanks for sharing.
@tommyzegers
10 ай бұрын
Great video. Thanks
@MWAWoodworks
10 ай бұрын
You're welcome 🤗
@MyGrowthRings
Жыл бұрын
Great vid! I’m a SpecTape man from way back! Thanks for sharing. Scott
@trickytricky100
Жыл бұрын
Hi what’s the model of the small drill your using to place the screws in, thanks great video’s helps out lots
@KrahsThe
Жыл бұрын
Question: the finish on 'finished plywood'. I've heard it referred to as clear coat. But what it is? It it from total boat? I'd like to replicate it, since I have a few cabinets already that were pre-finished ,but I'm building a set now that I'm making out of plywood that is not finished.
@MWAWoodworks
Жыл бұрын
It's definitely not Total Boat because it's not epoxy. I don't know exactly what is used but it's a clear coat finish that is currently with UV light. All that to say can finish your own panels with whatever clear coat you want and should be good to go.
@KrahsThe
Жыл бұрын
@@MWAWoodworks good to know! thanks.
@SawdustmakerLori
Жыл бұрын
GREAT video, so helpful......thanks for making it!!! I'm working with prefinished plywood for the first time right now. Is there a good way to apply finish (and what kind to use) to the exposed cut edges or should they just be left unfinished? Never knew you could paint it either so thanks for sharing how to do that. When you use the double sided tape for drawer slides, etc. do you just leave it on the project or take off after the holes are drilled and before installation? Thanks so much if you can answer these questions!
@jeffshackleford3152
Жыл бұрын
In professional world, we would use spray lacquer or whatever spray clear it was. Just make sure that it matches the color fairly well. Just spray that on the exposed edge of the drawer boxes facing up. Other than that, I can't think of any spot where you would have visible plywood end grain.
@SawdustmakerLori
Жыл бұрын
@@jeffshackleford3152 Thanks so much for taking the time to reply Jeff! You're the only one I received an answer from so appreciate it!!!
@jeffshackleford3152
Жыл бұрын
@@SawdustmakerLori No prob. I personally would test it out on a scrap, give it like an hour to dry, then see if you like it or if it matches well enough to be passable. It won't be perfect match, but that is the easiest way to handle that issue that I know of.
@SawdustmakerLori
Жыл бұрын
@@jeffshackleford3152 Great advice.....I'll do that. Thanks again and have a great upcoming week!
@talethawalker1111
Жыл бұрын
@@SawdustmakerLori Iron on edge banding is also easy to get the hang of. Watco satin matches well.
@aaronboschi7125
Жыл бұрын
Thank you!
@MWAWoodworks
Жыл бұрын
You're welcome
@alfredomendez3228
Жыл бұрын
Were can i get the router bit for the 1/4 in panel that is not a 1/4 in in thickness
Пікірлер: 272