Coolest piece of home boy engineering I've seen in a red hot minute. Many thanks, worked like a charm.
@eniamreg54
3 жыл бұрын
Glad I could help.
@rockrx7125
7 жыл бұрын
Having the same problem with my Gen5. Great info. Thanks!
@wyattdog877
3 жыл бұрын
Awesome. Worked like a charm
@reyiiteleco
6 жыл бұрын
Thx, very helpful, happened in my gen5 too after I install a QS. Seems like this a common issue for gen5 and qs.
@ethanwallis4910
25 күн бұрын
so it basically becomes a Manual CCT? I will be trying this later today. Did you put a nut on the main bolt to prevent it from backing out? similar to what you would get with a Manual CCT?
@juniorcates3343
2 жыл бұрын
Brilliant idea, about to do it on my gen 4
@eniamreg54
7 жыл бұрын
I had three things going on. 1 sudden idle surge. 2 long crank time, when starting. 3 lost of power at the top end. After adjustment all solved.
@hadaramibikerhadramout217
Жыл бұрын
bro, do i have to do TDC or not? do you prefer do the click trick way or take out the cct and reset it? i hope you response?🌷
@eniamreg54
Жыл бұрын
@@hadaramibikerhadramout217 no you don’t need to Tdc the motor. As you are not removing the chain. You will only need to remove it if you over tighten it to reset the cct. One or two clicks is what you are listening for.
@reggiesongz7646
2 жыл бұрын
Thanks Bro
@joseluisbermudezmerino2689
4 жыл бұрын
Thanks for the advice. Very good! How long should be the cutted piece you put inside the tensioner? Thanks.
@eniamreg54
4 жыл бұрын
Jose Luis Bermudez Merino about 3 inches. Just clip the short end off a Allen key and it should be long enough.
@Qomicbook
Жыл бұрын
mine is still rattling, could it be something else or maybe that the tensioner is completely shot?
@Moatz321
5 жыл бұрын
So my motorcycle Kawasaki zx10r 2016 I got such noise on the right side of the engine. Only replace the cct will disappear noise !!!!!!! I would be happy to respond to you
@danmello4603
6 ай бұрын
I got a 2016 i get to mine simple pull one small cover off it pop right off
@gzakelijk
16 күн бұрын
You sound like Norman Finkelstein.
@eniamreg54
13 күн бұрын
@@gzakelijk thank you
@Eddycarm
7 жыл бұрын
would you recomend me getting the original cct if my gen5 still has warranty or getting the ape manual cct?
@eniamreg54
7 жыл бұрын
Eduardo Carmona I would stick with the original CCT only because it's still under warranty.
@crokix
4 жыл бұрын
Did you place the allen bit inside the spring?
@eniamreg54
4 жыл бұрын
I remove the spring and the rod. Listen closely for the click. After each click start the bike and check the sound. You don’t want to over tighten the tension.
@colbyjerome4555
2 жыл бұрын
Hey I’m having the same issue and mines is back firing now after that started the bike wouldn’t stay on
@eniamreg54
2 жыл бұрын
Time to take it in to have the motor examined
@Mixd_NiNjA
5 жыл бұрын
What size Allen key is needed to shave off?
@eniamreg54
5 жыл бұрын
a 4mm should be fine.
@dhananjayatrey2822
4 жыл бұрын
This does not apply to the 2016+ Gen5 model. That bike comes with a non return type tensioner.
@eniamreg54
4 жыл бұрын
Explain 2016 and up having cam chain slack.
@dhananjayatrey2822
4 жыл бұрын
No noise in mine. It's a 2016 that's clocked 24k. The trick is to fix the chain right without slack between the cams and then unscrew the tensioner fully before letting it in the final position.
@eniamreg54
7 жыл бұрын
You will need this it helped a lot www.industrialsupplydenver.com/wi1sqdrrawrl.html
Пікірлер: 30