" Got a little fuel leakage there, nothing e are not used to" I couldnt agree with you more on these lol
@derekchapman184
2 жыл бұрын
That's the song that plays in my head when I'm turning wrenches, what are the odds
@kimproffitt9939
6 жыл бұрын
Love the Benny Hill music during the FF stages! Awesome. Seriously. Takes me back.
@vicentegonzales3852
2 жыл бұрын
Good video and good information about oversized to push in rubber seal … I use flat head a lot of work
@NothernXCanadian
3 жыл бұрын
Thankyou for the video, I have cylinder two's flue injector leaking. I have a 1993 Dodge CUMMINS 5.9L.
@briand3274
6 жыл бұрын
You should Not use Never Seize to hold on the washer cause it contains Metal! Use white lithium grease instead
@xXTheDecisionXx
3 жыл бұрын
Love the video. Straight forward love it.
@Nick-cg3mt
8 ай бұрын
What size fitting did you use as to seat those orings?
@mitchatkins4624
6 жыл бұрын
What is the size and spec of the plumbing fitting you used for the o-ring seating
@nevileasterling648
5 жыл бұрын
Yeah, please tell us what size
@williambaker7351
6 жыл бұрын
Does the fuel system have to be primed after new injectors are installed?
@CumminsWorks
6 жыл бұрын
William Baker You shouldn't have to prime the low pressure side of the fuel system. But you may have to loosen 3 of the injector lines and crank the engine over until fuel comes out and then tighten them up again.
@jeffweber144
3 жыл бұрын
What is the hold down nut O rings for? My new Bosch injectors didn't come with them.. they don't squash in so are they just a dust protector or what?
@CumminsWorks
3 жыл бұрын
It’s a dust seal to prevent dirt and moisture from getting between the injector nut threads.
@flatbedtruckr2392
8 жыл бұрын
I love it! Better video than the the 1st. Thanks for entertainment. I like your magic at the end. Hehe
@jasonlulich457
7 жыл бұрын
what tool did you use to seat the o-rings I called cummins and they have no clue
@jibber2210
Жыл бұрын
If the copper washer didnt come out, what is a good way to remove it? Good vid
@danielwilliams7824
5 жыл бұрын
Whats the plumbing tool you used?!?
@j.angelo2528
7 жыл бұрын
What can you expect from fuel economy with fuel injector change? Do you have any tips for better fuel economy?
@CumminsWorks
7 жыл бұрын
I'm probably not the guy to talk to, over the last 9 months I've averaged 13.7 mpg... Lol A lot of that is towing between 20k to 30k, plus being a farm truck it got a lot of short trips this year. And being honest, my driving style was not geared towards fuel economy. I can't say I have any hugely insightful tips, just the normal casual acceleration and minimal use of brakes. The other day I found out I had a sticking front brake due to swollen brake line. Rotor temp was 380°F while the opposite side was 110°F. So hopefully that will bump MPG slightly. So that'd be a good something to check. As far as injectors effecting MPG, typically you'll see a slight bump in fuel milage with new injectors due to them being set to a higher pop pressure (typically 280 bar) instead of the stockers which are set to 260 bar and typically fade down to 220 bar. If milage is the goal, a 5x10 to 5x12 is a good choice. Above that size, mileage can drop off some, nothing huge, maybe a mpg. Also, if you're wanting to up the fuel but keep your mpg, keep the stock DV's, larger DV's is a big player in lower MPG's. It would also be a good idea to check your fuel pressure, low fuel pressure can cause lower MPG due to inefficient burn. Cheers.
@spencersinclair-smith735
7 жыл бұрын
What does seating the o-ring do? What can u use to do that or where can I buy that tool
@CumminsWorks
7 жыл бұрын
The O-ring is just a dust shield, it helps prevent dirt from getting between the injector body and the head. That can cause the injector to get stuck in the hole, or abrasion due to all the vibration that occurs. Unfortunately I don't know where you'd get that tool. It was just a random fitting out of the plumbing bin. I'll see if I can shoot a quick video of the tool with some dimensions, so others can hopefully find something that will work similar. Take care!
@Luke_KJ
7 жыл бұрын
Is the process the same for a 2nd gen 12 valve? haven't worked on one yet
@CumminsWorks
7 жыл бұрын
Yes sir it is! The truck in the video is a 96 P-pumped 12 valve.
@bnorby213
2 жыл бұрын
Where do I get the o ring seat tool?
@justinkairo4988
Жыл бұрын
My injectors won’t stop leaking I’ve done what most ppl say to do when installing them, I even annealed the copper seals, cleaned the bores, torqued them. They piss out the return lines…
@BigMan-jk8lz
Ай бұрын
Replace those copper horseshoe washers
@salmendez6584
7 жыл бұрын
great video my 93 smokes white u think it could be injector because ones it running it goes away only in idle
@CumminsWorks
7 жыл бұрын
The Injectors could very possibly be the cause, you may not even have to replace them, just get them pop tested and bump the pop pressure back up as it tends to decrease 20-40 bar over time. 1st gens tend to be a little more temperamental in the smoke department though, so it's hard to say the exact cause. Best of luck!
@salmendez6584
7 жыл бұрын
CumminsWorks thanks man
@patricklacy7176
7 жыл бұрын
Salvador Mendez I'm having the same issue right now, mine smokes after you prime the fuel pedal for a while, white smokes once cranked then after I put it in gear and drive for about a half a mile it stops smoking and I'm about to replace the injectors, did it work for you?
@CumminsWorks
7 жыл бұрын
A little white smoke while cold is a sign of a incomplete burn, if it's really cold, on a diesel that can be a little expect, as they don't make enough heat to thoroughly burn the fuel. Advanced timing will cause more smoke, as will bigger injectors, lower pop pressure, or a worn injector with a bad spray pattern. If you crank the pop pressure up 20 bar from stock, that can also help with a cleaner burn and possibly a small bump in MPG.
@salmendez6584
7 жыл бұрын
Patrick Lacy bad injector let me know after u put injectors how iy was for u
@scottallen6970
6 жыл бұрын
Love the Benny Hill Music!
@Dodgemakesit
6 жыл бұрын
I want to know if there are diffrents between the engines. Auto180hp/Stick215hp 97 12valve ram. Just bigger injectors?
@CumminsWorks
6 жыл бұрын
The injectors are bigger on the 215 engines. Plus the injection pump is a little different as well. The governor weights are lighter letting it rev higher, and the plungers have a "retarding notch" which advances timing under heavy fueling. The AFC has a different spring in it as well. Off the top of my head, I can't think of any other differences. Best of luck to you mate!
@Dodgemakesit
6 жыл бұрын
Thank you so much for the quick response!
@Dontspeakboutme
3 жыл бұрын
Air ratchets are handy af btw
@4g63tpowered
3 жыл бұрын
Good god i wish my injectors just came out by hand. I got vice grips on em and I'm giving all i have and not 1 will come out!!!
@EastMenloPark1650
2 жыл бұрын
Did you ever get it out ?
@4g63tpowered
2 жыл бұрын
@@EastMenloPark1650 yes I did. Lots of patience and back and forth movement they finally came out. 3 of the 5 holes were completely clogged. I reinstalled dap +75 injectors
@derekchapman184
2 жыл бұрын
Mines got 953488 k on her and runs like a top
@superkittybtc
5 жыл бұрын
The ducking music is crap I had to mute it .
@adanvaldcontreras4283
7 жыл бұрын
what size injectors did you install? great video 👍
@CumminsWorks
7 жыл бұрын
In the video I installed 7x105 145° SAC injectors, but I didn't really like them so I moved on to a 5x13 145° SAC injectors and liking them a bit more. They're a decent 450hp injector, if you don't plan on going past 400hp, a 5x12 may be a better option. And Thanks!
@adanvaldcontreras4283
7 жыл бұрын
Thanks for the information
@tomduncan1970
7 жыл бұрын
How long does it typically take to complete this job?
@CumminsWorks
7 жыл бұрын
If you're familiar with wrenching, and nothing is rusted in place. an hour to pull them, and another hour to put them back in is reasonable. Once you do it a couple dozen times it gets a little quicker. lol
@trouthunter419
Жыл бұрын
What’s the price range nowadays days frm a shop?
@matthewgorgoglione5492
5 жыл бұрын
Next time I'm so playing this music📻🔧😋🚜📡🙌🚙
@zourdiesel8579
2 жыл бұрын
👌🏾💯
@stevestone6936
6 жыл бұрын
If you mess with this stuff and don't know what you're doing, it'll cost you a fortune.
Пікірлер: 54