Tim, I hope all is well. Great work on the 12 volt set up. I agree with you that the 12 volt has its place. Wash on brother!!
@ExpertPowerWash
7 ай бұрын
Thank you! Hope you are off to a great season!
@ktpowerwashing
3 ай бұрын
That set up sure looks familiar. Keep up the good work. Enjoy your vids.
@ExpertPowerWash
3 ай бұрын
Thanks, will do!
@salscavo3110
4 ай бұрын
Great video. When will you have more available? It shows out of stock on your website.
@ExpertPowerWash
4 ай бұрын
Waiting for a delivery.
@austinbarnes5476
Ай бұрын
Tim I’m running a shurflow 5.3 90 psi I have a 3/4 inch intake hose running to solution to 3/4 inch feeder hose to a 3/8ths hose reel manifold that had 100 ft of 5/8 flexzilla with a Softwash gun off Amazon the blue gun 16 gpm …I have a hard time keeping that pump with consistent pressure it’s almost like the pressure builds great but as soon as I spray it can’t keep up anything to. Change?
@carpetmagicofwilson
7 ай бұрын
Great video, I run a 12 volt setup, it has 7gpm 100 psi pump, i'm noticing when i pull the trigger i get my full distance then within 5 seconds or so my distance drops about 6 or 10 feet, it has 1/2" hose on the reel. coming out of my metering system is a 3/4" hose feeding the pump, i have 1/2" water line and 1/2" bleach line going into the metering valves. Any ideas Thanks
@ExpertPowerWash
7 ай бұрын
Sounds like air in the line for sure. Go through every single piece of your plumbing.
@Thetruthhurtstrump2024
Күн бұрын
Does it damage the pump leaving this outside in the elements?
@ExpertPowerWash
23 сағат бұрын
Not at all. Just don’t let it freeze which is pretty standard would everything.
@hfdg3
Ай бұрын
Can you tell me where I can find that rocker switch? Thanks
@ExpertPowerWash
Ай бұрын
We sell it. pressurewashingskids.com/products/soft-wash-12-volt-switch?_pos=3&_psq=Switch&_ss=e&_v=1.0
@RickHamilton-nk5pi
5 ай бұрын
Tim, when you guys set these up on your rigs what size plumbing do you use coming into and out of the pumps? Great video!
@ExpertPowerWash
5 ай бұрын
3/4 from the mixer to the pump. 1/2 out. You have to remember the pump is 1/2 and so is the hose reel. I’ve tested other options and we land back at this for the best all around performance.
@RickHamilton-nk5pi
5 ай бұрын
@@ExpertPowerWash Thank you, Tim.
@ktpowerwashing
5 ай бұрын
@@ExpertPowerWashspraying with 1/2" hose or 5/8" hose? Your comment leads me to think 1/2", keeping everything consistent with pump outlet size, hose reel in/out.
@mr.skeptical3071
Ай бұрын
I thought that a 5.5 12vollt would be way faster flow than a 4gpm gas
@ExpertPowerWash
Ай бұрын
Well it's pushing more GPM but it's only 100 psi but your average 4 GPM Gas might be pushing a little less water but it is also 4000psi
@jerrymeyers2075
7 ай бұрын
Do you sell this setup on it's own?
@ExpertPowerWash
7 ай бұрын
Yes I do. Here’s the like, pressurewashingskids.com/products/mounted-remco-5-3-gpm-60-psi-softwash-pump?_pos=3&_psq=Pump&_ss=e&_v=1.0
@jerrymeyers2075
7 ай бұрын
@@ExpertPowerWash thanks for the quick response I'll be ordering one next week
Пікірлер: 22