I found it much much easier to take the passenger side motor mount out, supporting the engine with a floor jack and do it from the top. That way you can jack the engine up and down, remove the water pump pulley completely for unneeded access, and you don’t have to remove the crank pulley. Plus, it makes putting the belt on a breeze.
@M.TTT.
Ай бұрын
Hmm, seems not too bad a job
@forevr_8
8 күн бұрын
Wow, that’s some expert upselling. Good!
@maxsmoviechannel2025
8 күн бұрын
@@forevr_8 this one was warranty repair!!
@chenlongchen3483
Жыл бұрын
Such an assss pain to replace that tensioner :(
@maxsmoviechannel2025
Жыл бұрын
It’s definately not easy my friend
@luxuryacuraz
Жыл бұрын
Great Video
@maxsmoviechannel2025
Жыл бұрын
Thanks for watching brother
@carloslopez-lt1zl
5 ай бұрын
Thanks brother
@user-wm4bo4nj8l
Жыл бұрын
Do you really must install the belt tensioner when replacing the serpentine belt ? Looks hard and to much work ahhhhh
@maxsmoviechannel2025
Жыл бұрын
I replaced the tensioner for a whining noise, but if you just want to change the belt you can.
@user-wm4bo4nj8l
Жыл бұрын
nice active @@maxsmoviechannel2025
@danicooper6550
Жыл бұрын
How did you get the serpentine belt back on? Every video shows the after effect.
@maxsmoviechannel2025
Жыл бұрын
The best way is to route the belt from the bottom, get the belt onto each pulley but do the waterpump (the big non-grooved) pulley last. It’s still a mission…. Watching this video again, I realize I did the alternator pulley last, but the other way is easier
@richardpvancouver7520
Жыл бұрын
Why can't balancer be removed with regular 19mm socket ?
@maxsmoviechannel2025
Жыл бұрын
Good question. In theory you CAN take it off with a regular 19. But the special socket is MUCH thicker and built for that. Less chance of breaking a socket
@richardpvancouver7520
Жыл бұрын
Thanks I'm doing my dad's on sat !
@maxsmoviechannel2025
Жыл бұрын
Anytime my friend and good luck! Remember the trickiest part is the water pump pulley. You can’t get it out fully. So find a bolt that can hold the pulley while you break the bolts loose with a ratchet. Also when removing just tuck the pulley up and to the left, it will stay pretty good in that position if you get it right
@peepeeskillz
Жыл бұрын
what did you torque the crack pulley to?
@maxsmoviechannel2025
Жыл бұрын
No real torque spec, just use a regular 19 socket (not the thick one we used to take it off) and gun it down nicely.
@cultusgti
5 ай бұрын
Who you call'en boy!
@janjrod
Жыл бұрын
Thanks
@maxsmoviechannel2025
Жыл бұрын
Anytime man
@louielouie8080
Жыл бұрын
Awesome video buddy,. Great to see you using tools made 🔩🔧🔩🔧😎 makes job go quicker
@maxsmoviechannel2025
Жыл бұрын
Hey thanks brother! I have a good video for tomorrow where everything goes completely wrong haha
Пікірлер: 25