"put on with a blow torch" 😂 Great videos btw. I hope you keep them coming.
@ToltecMerc
2 жыл бұрын
Thank you! I'm trying.
@B9NE
2 жыл бұрын
You were missing a 6 pin regulator under that USB filter
@efrendelgado6824
2 жыл бұрын
Keep up the great work, 👏
@ToltecMerc
2 жыл бұрын
Thanks!
@LexLinux
2 жыл бұрын
omg that port looked TERRIBLE LOL thankfully you made it look perfect!
@ToltecMerc
2 жыл бұрын
Thank you very much!
@rfr653
Жыл бұрын
Good job mate 👍
@ToltecMerc
Жыл бұрын
Thanks 👍
@B9NE
2 жыл бұрын
I'm guessing all the pins aren't connected before the end of the video
@bradlyely
3 жыл бұрын
Much appreciated!
@consciousone894
2 жыл бұрын
How do you remember what screw goes where? You seem to put them all in one pile lol
@ToltecMerc
2 жыл бұрын
Yes I do. It's just from repetition. After a while, you just know where they go.
@B9NE
2 жыл бұрын
When the light shuts off on the amp meter it's usually the m32 even with no obvious shorts.
@MasterJediSean
Жыл бұрын
I really like how you make your own pad trace replacements. I mentioned this before and you told me how you make them yourself using your pliers crotch to squeeze them flat. This is by far the best technique I've seen so far. Great Work my friend!
@ToltecMerc
Жыл бұрын
Thank you so much! That's very kind of you!
@hove131
2 жыл бұрын
How do you smash your jumper wires flat like that? Love your content by the way. Been watching for quite some time now.
@ToltecMerc
2 жыл бұрын
I have a pair of needle nose pliers that have a flat area between the jaws. It's just before the area with teeth. I just take a small piece of wire and flatten between the smooth area of the jaws.
@spot-technology
3 жыл бұрын
Hi my friend, I am looking forward to watching a video on laptop repair
@ToltecMerc
3 жыл бұрын
I will see what I can do!
@kingvon0125
2 жыл бұрын
My Switch only gets 0.1 amps. Doesn’t power on or even show the battery charge icon in the corner. Any idea what my problem could be?!?
@ToltecMerc
2 жыл бұрын
I would check the M92T36 IC.
@B9NE
2 жыл бұрын
Yep check the m92 and bq chip. If no shorts I would check the fuel gauge ic max 17050. It's usually the culprit at .1 amps. Do you have coil whine?
@MicroMageRepair
3 жыл бұрын
Nice work on the trace repair, particularly liked the wire smash method, worked out to be very slick.
@ToltecMerc
3 жыл бұрын
Thanks! I appreciate it! I've tried that method before but I didn't have the green solder mask back then. That stuff makes it possible.
@sandovalvic
2 жыл бұрын
Yeah that was genius. Curious how did you smash the wire?
@ToltecMerc
2 жыл бұрын
@@sandovalvic my needle nose pliers have an area close to the pivot point that is flat/smooth.
Пікірлер: 27