Awesome demonstration thanks! Only tip I would add is to make sure that your walking path is clear. Don't trip over debris while you're cutting. I especially like the tip about shutting you're tool boxes while working! I've forgotten a few times and had to shake out the tool box . . . dumb! Thanks again FloweringElbow!
@FloweringElbow
3 жыл бұрын
Hey Ryan, thanks for the encouragement and the point about having a clear working area - that's one I forget/ willfully ignore all too often, usually to my detriment.
@hubertusthelen8299
Жыл бұрын
Thank you for all those important tips. Seeing your older clips makes me milling with my MS 660 and you are right. Pure fun in the nature.
@patrickforbes6745
3 жыл бұрын
Tip #1 should be “Warm up your saw before cutting.” This will help the piston and exhaust port to warm evenly and extend the life of the saw.
@FloweringElbow
3 жыл бұрын
Nice tip Patrick, thanks for sharing.
@samp3922
2 жыл бұрын
You are absolutely correct. That saw is a precision piece of machinery built to close tolerances. Early grave if you don’t warm it up-
@jaredmullins3255
2 жыл бұрын
I'm still very new to chainsaw milling but before I ever made my first cut I let the saw idle for 1 minute and when I was done cutting I let it idle for 2-3 minutes. I definitely don't want to kill my saw.
@aerialrescuesolutions3277
2 жыл бұрын
No matter what you are cutting, a chainsaw should always be warmed up. If you plan on rebuilding your saw each year or two then do what you like.
@chainsaw_Expert_Chris
8 күн бұрын
Great tips in this video! I really appreciated the advice about starting and finishing cuts smoothly-it’s something I often overlook. Also, the idea of using a ladder for checking straight cuts is genius! Have you had any other experiences where small adjustments made a big impact? Looking forward to hearing more from you!
@FloweringElbow
8 күн бұрын
@chrisross9631 Hi Chris thanks for this. There are so many elements that make up a nice smooth cut it's hard to single any out. If you're interested in this, maybe check out our book available on the flowering elbow ko-fi page. Thanks again for watching.
@eCitizen1
Жыл бұрын
A brush is a good tip for me, since I usually use compressed air to blow everything clean. Not much option to get compressed air when you are in the woods. Using the rail for every cut is a very good safety tip. Thanks for that. I usually sharpen the chain with a 12v Granberg chain sharpener before long sessions. I monitor the duty cycle of my Stihl carefully, and let it cool down for more time than the cut time. I really appreciate your tip about 45 degree angle cuts, lubricating with cheap oil, and wrapping the bar with rubber. All things I had never considered. I usually remember to put in the ear plugs, hearing protection and respirator, but often forget when other people are helping to have another set. I wear heavy leather gloves, heavy coat and hard shoes when using a chainsaw. (Stihl chaps, for helpers) I've been using plastic shims, but will change to the type you showed with a much longer taper. I use a log dog to move logs. Moving logs and slabs is a headache, as is working in an environment with slopes, rocks, boulders and debris. A rope, nylon strap and/or even a come along can be useful. If the bark is loose, I try to remove it before milling. Tools for that is helpful. I keep a first aid box with bandaids, blood clotting powder, compression wraps, athletic tape & snake bite kit. (Especially for when someone else is helping me).
@FloweringElbow
Жыл бұрын
Hi Larry, thanks so much for sharing your experience with us. Are you running the saw at idle to let it cool, or just off? That duty cycle is very generous on the saw? Thanks again for sharing and for watching. appreciate that :D
@eCitizen1
Жыл бұрын
@@FloweringElbow Cool down means off. I'm very mindful to never overheat my chainsaws. It keeps them working like new much longer. Also careful to never run out of gas or oil while cutting. A little care goes a long way
@rokasklemaitis4958
5 ай бұрын
I liked the tip nr. 9 the most! But actually all of them were really great! Thank you!
@spkay31
7 ай бұрын
Great tips for Alaskan chainsaw milling. I just got started with an MS660 clone and a 28" bar. My little tip is use a longer bar/chain. Sure it's more than I need for what I am milling but the advantage of the longer bar (as we see in your video) is that the chain is out of the cut for much longer time and the number of cutting teeth is much greater so each tooth is sharing the load much more than a smaller bar/chain. I am now ordering a 36" which should be better for cutting the 12"-18" widths I need from my current lumber.
@freedomforestlife
Жыл бұрын
mate thank you so much for taking the time to put the mask info in the description, i lost my voice last week milling all day, and the masks from screwfix were close to £200 so thnk you!
@FloweringElbow
Жыл бұрын
Very welcome friend!
@jeffery19677
3 жыл бұрын
One of the best videos so far! I haven't seen them all, yet. Key word. YET.
@dochertyinbc
3 ай бұрын
I no longer use wedges, in large part because they tend to either lift the guide level, or like to fall out. Additionally, they need to be inserted from both sides of the log. To overcome these issues I have cut a large collection of slats the same thickness as the chainsaw kerf. I slide them in without undue pressure and they are wide enough to support all the way through.
@FloweringElbow
3 ай бұрын
Great tip!
@timgreen3770
4 жыл бұрын
Just found your channel. I've just ordered a mill and have 65 acres to explore cutting my own lumber. This video shares a wealth of knowledge, especially some tips I wouldn't have considered. Thanks, and I'll be checking out your other vids!
@FloweringElbow
4 жыл бұрын
Welcome Tim. Sounds like you have some satisfying but challenging learning ahead. Great to hear from you,, Bongo.
@raimopuuvark
Жыл бұрын
Nice video,thank You👍🏻One tip i would like to add:if you cutting lets say 18” slab,dont use 36” bar for this,use 20” bar instead.You’ll be surprice what your saw’s capable.It’s good to have a good variety of sawbars.Just my toughts. Thank You👍🏻
@B_Van_Glorious
Жыл бұрын
Well even after taking the dogs off the saw (which you should absolutely do when milling) you are already going to lose 2 inches+. I'm about to go start up my 660 on a granburg and I couldnt do an 18in with a 20. Min 22. That being said, Im running 28 to cut 22-24. I want the extra chain out of the cut so the saw doesn't heat up as fast.
@mateofleet3390
2 жыл бұрын
This was the most helpful tip video I have found about chain saw milling. Thank you
@wehttam2358
4 жыл бұрын
Thanks for the advice friend! This made my first attempt at chainsaw milling a productive and enjoyable experience. I was able to get some very nice slabs out of some oak logs left by a recent forestry harvest on our land. Cedar shingle off cuts make very nice wedges you don't need to worry about breaking.
@FloweringElbow
4 жыл бұрын
Hi Wehttam, great to hear that, thanks for reporting back :D
@victoryfirst2878
2 жыл бұрын
Hello my good old friend BONGO. Was such a great thing for me to run into your video Sir. Hope all is well and you keep on making great things for us all to see and learn from. You rock fella. Peace Vic
@FloweringElbow
2 жыл бұрын
Thanks Vic 😊 always a pleasure 🙏
@victoryfirst2878
2 жыл бұрын
@@FloweringElbow Just hope I get a chance this year to visit the large island. Will surprise you fella. Peace vf
@SethWilcock
2 жыл бұрын
Best video I've seen on chainsaw milling so far. Thank you! Great cuts!
@FloweringElbow
2 жыл бұрын
Hey thanks Seth, check out the more recent one's for updated tips ;)
@lindanwfirefighter4973
3 жыл бұрын
I bent my bar after only 10 cuts. 😳 I wish I had seen this video before I dived in. Learned lots. Thanks.
@mattdg1981
4 жыл бұрын
I milled my first slabs this past weekend in some 16" northern pine. After a few passes through a 4' long log and my saw was empty. I have cut down alot of trees in my younger days but I have never burned through fuel so fast. I do have a larger saw (stihl ms440 magnum) so I should have expected it but after only 20 mins of hard sawing my saw was dry. That was hardest I ever pushed my saw but it didn't bog down once. I do have to get a skip tooth ripping chain. It would make cutting alot easier and faster. I'm really enjoying this newfound hobby and cant wait to work my handsawn material in the shop.
@FloweringElbow
4 жыл бұрын
Good morning Matt, thank you for getting in touch. Sounds like you're getting the cs milling bug ;) Yeah, when you think about the amount of time actually running wide open throttle during ground work, you can see why the difference in fuel consumption. Milling is basically 100% WOT. I recon general ground work and cross cutting can be something like 10-40% depending on how full on you go, the rest of the time you are thinking, moving, unsnagging yourself etc. If you're not bogging the saw down milling, then I'm not sure a skip tooth ripping chain will be a whole load better. Have you seen the vid on sharpening? It goes into standard vs ripping chains a bit. You might want to try filling the depth gauges a bit if the saw's not having any problems - one of the biggest differences between stock rip and crosscut chains is the depth gauge height (rip chains tending to take a bigger bite)... Thanks again, Bongo.
@hermanhosenknopf5331
4 жыл бұрын
I just watched this video kzitem.info/news/bejne/l2tpzHmeknVhhoY about Granberg Ripping Chain which resulted in finding this one here. Someone in a German Chainsaw Forum recommended to file down a 10° chain like this. He claims to cut almost 2 times faster with a severe lower fuel consumtion. Link to his post: motorsaegen-portal.de/viewtopic.php?f=61&t=111932#p1732085 Might be an idea, I just ran through 2 tanks on my 064 (3/8", 1 meter) cutting a 1,6m, 45cm diameter Maple into 7 or 8 boards
@VinnyMartello
2 жыл бұрын
Thanks for the tips! Proud owner of a big bad Husqvarna 395XP and I just ordered a ripping chain. About to order a grandberg sawmill.
@FloweringElbow
2 жыл бұрын
Hey, thanks for watching. Good luck with the milling!
@Mwfrizzellandsons
2 жыл бұрын
Excellent info.
@FloweringElbow
2 жыл бұрын
Glad you think so, thanks for watching :D
@CH-so8tn
3 жыл бұрын
These tips sounds like good advice for first time a nal
@waltergreene8880
6 жыл бұрын
Absolutely the best video on the proper way to use the mill I've seen yet. And I've seen hundreds where they just talked about themselves. Very useful for me....
@countrywoodproducts
Жыл бұрын
I am seeing a lot of people saying that you should use the straight edge always when running alone. I am watching videos before firing up my own Alaskan sawmill for the first time ever. I am no stranger to mills but never used the Alaskan mill yet.
@FloweringElbow
Жыл бұрын
I recommend it. Not only save on cumulative error headaches, but way safer... Good luck friend. 👍
@benyeargin1005
Жыл бұрын
thx for the video. got a bunch of great advice out of it
@FloweringElbow
Жыл бұрын
Great to hear! Why not consider the ebook too 😉 Thanks for watching Ben, peace.
@LolitasGarden
6 жыл бұрын
I paint my wedges blue. Nothing in my area is blue. In autumn, about half the ground is red and orange. Good tips. Subbed.
@FloweringElbow
6 жыл бұрын
Lolita's Garden nice tip. If / when I get round to painting them I may go blue... Will see what scrap paint I have ;)
@andrewfrudd108
3 жыл бұрын
Paints wedges blue, next milling job - bluebell woods 😁😁 A colleague of mine set out about a hundred trenches one week with blue pegs. Next week they came to machine them and all the thistles were in flower
@ejsocci2630
Жыл бұрын
Awesome awesome, thank you for sharing, love your videos.
@medardo94mwale
Жыл бұрын
Thanks for the tips it's so important
@davidwillett53
Жыл бұрын
Saw arrived yesterday kzitem.infoUgkxfQm1wmg0ItKDLavxj1nXtQY9HP7EF504 and today I cut about 3/4 cord of wood with it. Make sure you get an extension chord that is at least 12 gauge wire, minimum. This is my first electric in about 10 years, and things sure have improved. The self-sharpener works great, and it just kept cutting through some pretty decent logs. Wear your eye protection, and ear protection. Excellent saw.
@Casa1910steve
4 жыл бұрын
I wish I could have given 2 thumbs up. haha...I have been logging since 1999, but am just about to start researching some chainsaw milling using my Echo CS-620PW with a 27" bar. Just to start. I've actually free-hand milled some 18" (green) red oak with a CS-400, but it took flippin' forever. It worked, though. I'd imagine the 620P should be a bit quicker, and I have a buddy milling some beautiful planks with a 590 Timberwolf and a $200 Granberg (?) mill setup, with really nice results. I'm loving this whole concept, so thank you for some good pointers ~ I'll be trying them soon!
@FloweringElbow
4 жыл бұрын
Thanks man! means a lot. Hand milling is tricky, but possible - so much technique involved - am in awe of people that can do it well. Checkout some of my other vids on CS milling for more up to date tips. Best of luck with it!
@Casa1910steve
4 жыл бұрын
@@FloweringElbow - thank you! I'll do that.
@ryancivil
6 жыл бұрын
Hahah love the Starwars reference! thanks for the video!
@secretspy74
4 жыл бұрын
Great video. I am milling my first logs this weekend....this is very relevant!!
@FloweringElbow
4 жыл бұрын
Good morning Secretspy, thank you for reaching out, and good luck milling. Let me know how it goes? Peace, Bongo.
@secretspy74
4 жыл бұрын
Hey Bongo, it was great fun. Ended up with sixteen 6ft by 1ft by 1-1/2" cherry slabs and some other experimental off cuts. The logs cost $40 from a local fire wood cutter including delivery! Your tip about stopping to enjoying the experience of milling rings true.
@TonysTractorAdventure
4 жыл бұрын
I really appreciate your video. I just ordered a push type chainsaw sawmill from Norwood. All of your tips make so much sense. Thank you again. Tony
@FloweringElbow
4 жыл бұрын
Hi Tony. That's really great to hear! Wish you lots of luck with it. Let me know how it goes. Cool tractor vids BTW. Love the little dude with the demountable digging boom... Peace, Bongo.
@skipbickford3970
2 жыл бұрын
Thank you
@kennethperian4370
3 жыл бұрын
Great job showing and telling, keep on sawing that wood, and loved those tips I’ll use them. So see ya on the next time have a great day.
@edwardtagg
2 ай бұрын
You're a super great guy... bless you
@clarkg9805
Жыл бұрын
Great tips thanks for sharing , love your hat, wishing you the best.
@thomastieffenbacherdocsava1549
6 жыл бұрын
Reasonable and safe when using a really big saw out there by yourself. Will be using your tips on my more urban project cutting a very large diameter black walnut. Thanks!
@RockhillfarmYT
3 жыл бұрын
Well done
@cristijndevin2900
6 жыл бұрын
i've putten some rollerbladewheels on my millframe, to guide it along the tree. works a dream!
@FloweringElbow
6 жыл бұрын
Cristijn de Vin nice tip. I actually had that on my setup but didn't get on with it when the log had uneven edges. The roller wheel would want to push the saw too much into the cut when 'rolling down' into nooks. It was very nice on straight trunks though..
@cristijndevin2900
6 жыл бұрын
FloweringElbow ; i recognise what you are saying; but if i dont use the wheels the saw can pull itself tight against the first stand of your mill. Nice tips! Tnx. And tip #18; use Aspen fuel!
@1320crusier
2 жыл бұрын
Add a winch and snatch block. It is a must have mod. I know I know 'dont push and all that but my saw thrives with a bit more load on it than a chain pulling through will put on it. It improved the speed, finish, and efficiency of my cuts too. Try it!
@FloweringElbow
2 жыл бұрын
Thanks for sharing your feedback. I do plan to try it. Will report back....
@jeremyjenks
2 жыл бұрын
This is cool and way helpful tip tip
@scatoutdebutter
11 ай бұрын
Thanks!
@callie_waldschmidt
2 жыл бұрын
Very helpful. Thank you for sharing your expertise!
@FloweringElbow
2 жыл бұрын
Glad it was helpful friend :D Cool vids BTW, I had a quick look at your channel.
@callie_waldschmidt
2 жыл бұрын
@@FloweringElbow Thank you! I plan on using my slabs for a workbench and a mountain bike trail. Really appreciate it!
@110americalovingpatriot2
3 жыл бұрын
I started sharpening my chains with a Dremel I got at home depot. You can get a rechargeable one you can take into the woods or a plug in one. They have tons of attachments for all kinds of stuff and the one for sharpening chains comes with 3 different size grinding stones and an attachment so you get the perfect angle. Its a whole lot faster than using files.
@FloweringElbow
3 жыл бұрын
Interesting thanks. Looking into this, seems a nice in field option. How long do you find the grinding stones last? What type? Does the dia. of the stone change during use much?
@clydecramer8946
3 жыл бұрын
@@FloweringElbow I've used them alot and they work great, just don't buy the cheap bits. Get the good bits from Dremel, Oregon, or other name brand. I've had the cheap ones not last through one sharpening but, I've had name brand ones last me longer than files.
@110americalovingpatriot2
3 жыл бұрын
@@FloweringElbow when I first started sharpening chains with the Dremel I was staying on each tooth way too long and by the time I had finished two yellow dot chains for my 30" bar, but once I figured it out I get about 6 to 10 sharpenings for chains on the 30 inch bar. I ran out of grinding stone bits and I was in a pinch so I ground the rest of the stone off of the rod that holds it in the Dremel then took one of my cheaper 3/16 or4.8mm files and cut a piece off about 1" inch long then used my drill press to drill a hole perfectly in the center the same size as the rod the stone was on and secured it with Gorilla fast drying super glue. You would be surprised how good it works even though it's not sharpening in the right direction cause it's spinning. When u made the next one I secured it with J.B. Weld cause the other one came loose and flew off. And yes it did change the diameter of the stone. Hope this helps. I did buy the Dremel brand Dremel. Amazon has them or if you get on eBay and type refurbished in front of whatever you want to buy except underwear haha you get a pretty good deal and some of it is actually brand new.
@arcanewyrm6295
2 жыл бұрын
Just watch you don't burn the teeth when using any kind of powered grinder to sharpen. They're small and will heat up pretty quick and get brittle. Filing only takes a couple minutes with a little practice, and you'll never risk burning the teeth up. Plus, files are cheap and don't have batteries that you can forget to charge.
@nichosoulsea1
5 жыл бұрын
Loved the vid. Done a bit of chainsaw milling. I also use a ladder on all cuts, makes entering and exiting cut a lot easier. And then with the long ladder I can do 5 meter slabs. Had the 661, getting a 461 next week. Going to put carbide chain on it from Rapco industries. Apparently the cuts are almost planer smooth and the carbide does about 4-5 times the work before it needs a resharpen and cuts easier than steel putting less strain on engine.
@Mote78
5 жыл бұрын
Hi, Paul. Any update to your carbide chain for ripping? Does it produce smoother cuts and longer lasting? Can you resharpen it using regular equipment?
@FloweringElbow
5 жыл бұрын
Hey Paul, thanks for the comment. I too would like to know how the carbide experiment worked out?
@blackflycanada4943
5 жыл бұрын
Thank you for the info, greatly appreciated. I just built my first mill. Got a 36" bar for my saw, and plan to start milling my own lumber very soon. So thanks a lot!
@FloweringElbow
5 жыл бұрын
Awesome! Let me know how it goes :D
@blackflycanada4943
4 жыл бұрын
@@FloweringElbow So I did get my mill workin. I fell a large spruce and milled 4 of 26" wide x 9' long, 3.5" thick slabs and a 7"x7"x9' beam for a family dining table. Along with a bunch of thinner slabs for future projects. Your tips and info was extremely helpful. So thank you again! I intend to go back and mill the rest of the tree. No sense in wasting any of it. It was a blast and I am totally hooked.
@FloweringElbow
4 жыл бұрын
Hi@@blackflycanada4943, great! Heartening to hear :D
@johntillotson4254
2 жыл бұрын
Enjoy your videos
@grege8716
3 жыл бұрын
Tip #9; My Favorite!!
@morelovenaresh
2 жыл бұрын
nice technique
@FloweringElbow
2 жыл бұрын
Thank you! Cheers!
@seanf7810
2 жыл бұрын
I've got a tip: trim the limbs right down to the tree. The engine rides along the tree (the chain pulls it in) and running into limb nubs will really throw off your groove.
@jesseoglidden
4 жыл бұрын
Thanks for talking me out of chainsaw milling.
@FloweringElbow
4 жыл бұрын
Hi Jesse. Thanks for the comment. Haha. It's a lot of work ;)
@ScottSpeedPro
3 жыл бұрын
Thanks for the tip on using the ladder for subsequent cuts. First time ever using a sawmill today, I did the first leveling cuts on two red oak logs (didn't wanna keep adjusting the height bar back and forth) and the thought of trying to maneuver a heavy mill while keeping it perfectly level until the second bar finally connects does not sit well with me. Very helpful!
@FloweringElbow
3 жыл бұрын
Great to hear. thanks Scott :D
@nicholasjones9163
2 жыл бұрын
Awesome video Man, really learnt some good things. 😁
@liquidwarriors6793
2 жыл бұрын
great tips man!! thank you so much
@em4703
2 жыл бұрын
Top ends seem to last substantially longer with a 33:1 or similar fuel-oil ratio compared to 50:1. Main crank bearing wear seems also reduced on saws I've seen with 3000+ hours on them. I've never seen a saw with that many hours and still kicking running 50:1 :P
@FloweringElbow
2 жыл бұрын
Yeah, interesting. I have heard similar before, and I do tend to generous mixing with the oil. My only reservation, is that the fumes when burning more oil are even less pleasant...
@love2exploretogether
2 жыл бұрын
Thank you very much for the tips!!!
@FloweringElbow
2 жыл бұрын
You're so welcome!
@wankksh8454
3 жыл бұрын
Good toturial...
@gordonturner8544
4 жыл бұрын
good video. some new information such as angle of attack very helpful.
@FloweringElbow
4 жыл бұрын
Hi Gordon. Thanks for the encouragement. Peace, Bongo.
@JandSChainsaw
5 жыл бұрын
alot of good tips! ive saw several others on youtube recommending a winch on the mill,like stated in this video your saw should pull itself through the wood if the chain is sharp....
@FloweringElbow
5 жыл бұрын
That's my feeling anyway. I imagine it would be easy to keep sawing long past when the chain should be sharpened... That and the fact it's all extra setup time and kit to transport mean I haven't ever actually tried a winch, so can't really comment ;)
@bobspring6723
2 жыл бұрын
Just subbed. Helpful thks.
@robjackson2731
4 жыл бұрын
Thanks for making this video. Looking to get started with my first slab harvester setup very soon here
@FloweringElbow
4 жыл бұрын
Good luck!
@dalehelms4739
2 жыл бұрын
The man
@northwoodsinthebackwoodssa6752
3 жыл бұрын
Very nice informative video! Thanks for sharing, and your good knowledge!
@stephenalibozek1058
2 жыл бұрын
Good job thank you 👍👍
@daveoseas
Жыл бұрын
Wonderful. Thank you.
@FloweringElbow
Жыл бұрын
Our pleasure!
@bryankeeler3372
6 жыл бұрын
Entertaining and useful tips. I've ordered my mill and expect to benefit greatly from your experience. Thanks much.
@FloweringElbow
6 жыл бұрын
Bryan Keeler thanks :D Let me know how it goes...
@aragorn1079
4 жыл бұрын
That was a great video thank you. My Alaskan sawmill just arrived a few minutes ago. Really great advice!
@FloweringElbow
4 жыл бұрын
Good evening Big Tuna. Thank you for your comment. It's a steep learning curve and quit addictive ;) good luck with your new mill :)
@aaronandrews166
3 жыл бұрын
You make awesome videos with this stuff. Thanks!
@FloweringElbow
3 жыл бұрын
I appreciate that, thanks Aaron!
@TilkRaivo
Жыл бұрын
The important thing you definitely already know. The sharpening angle of the saw chain when sawing longitudinal wood must be 10° insted 35°. The saw blade remains stable and the table surface is smooth. 🙂
@Jamestfarrell
6 жыл бұрын
I'm stihl waiting on Tip Number Nine........The rest are making the wait worthwhile!
@FloweringElbow
6 жыл бұрын
Hehe. Nice one Jimmy... Have a look here "Tip Nine 07:00". I know it's confusing when 9 comes AFTER No. 17 right?
@briankleinschmidt3664
2 жыл бұрын
You make this look like back breaking labor.
@FloweringElbow
2 жыл бұрын
lol, I do try!
@curtissiwak5349
6 жыл бұрын
Thanks for sharing, I think I am going to start milling as a light hobby.
@canadub1983
6 жыл бұрын
LOL. Can't wait until you've bought 5 chainsaws and built yourself a log trailer and a kiln for your "light hobby". (or at least that's what happened to me when I said that...)
@johnroper-paris1369
6 жыл бұрын
Great sharing of knowledge and experience, agree with everything you've said.. I hadn't thought about the slowing down on exit though, makes sense. One tip for your next video is to try and mill down hill, I learned that one very quickly...
@FloweringElbow
6 жыл бұрын
Yep, always mill on a slight slope if possible. Very good advice.
@garyglenda2809
3 жыл бұрын
Using the ladder as a guide also can help to avoid dipping the leading edge of the bar of the saw as the front mill frame passes the end of the log
@FloweringElbow
3 жыл бұрын
Yep, good point Gary.
@humansustainability
Жыл бұрын
so much fun, thanks
@hiphop666
3 жыл бұрын
Digging the happy Vibes Bro. About to make a mill. Going threaded rod/ board combo. Have a 42 inch bar. 37 inch Ash Log. Too large for my bandsaw mill. Gonna saw 8" slabs. Transfer to Woodmizer. Resaw into lumber.
@FloweringElbow
3 жыл бұрын
Hey thanks man 😃 Sounds like a plan.
@hiphop666
3 жыл бұрын
@@FloweringElbow couldn't have done it without Y O U!!! I'm in East Tennessee. Where abouts are you?
@FloweringElbow
3 жыл бұрын
@@hiphop666 Thanks :D We're in Wales. Over the pond!
@starnes87
5 жыл бұрын
Your tips are really good as most of them I have used.
@TELOYSTV
2 жыл бұрын
Nice my boss..👍 Keep safe to your freehand mill 🙂
@BernardJustusMuhwezi
5 ай бұрын
You mentioned other videos on constructing your sawmill? Otherwise thanks for the tips, they are very helpful.
@cdawg9149
2 жыл бұрын
Since Ive watched this video Ive milled around 300 slabs. Im coming around to using the ladder on almost every cut now. Mostly because of the safety factor on starting the cut. I usually dont have the luxury of having the log elevated off the ground since they are big trees I mill. I wish there was a way to redirect the exhaust in a different direction since it kicks up a lot of dust and fumes on the last couple cuts. Maybe sthil can come up with something. I still swear by the winch.
@justnate78
2 жыл бұрын
Great video. Thank you.
@FloweringElbow
2 жыл бұрын
Thanks Nathan, appreciate the encouragement :)
@robertward553
3 жыл бұрын
Great video, great tips, easy to listen to, all in all, I like it. I subscribed.
@FloweringElbow
3 жыл бұрын
Welcome Robert. Thanks man :D If you're into chainsaw milling, hopefully you'll like some of our other vids. Peace, Bongo.
@rylanpolkinghorn4031
4 жыл бұрын
Really good video thanks
@FloweringElbow
4 жыл бұрын
Good Afternoon Rylan, Thanks for your encouragement :D
@rodneyrockwell9967
4 жыл бұрын
Good job
@Darrenholmes
4 жыл бұрын
Great clip, I would of liked to hear how you secure the ladder to the log prior the first cut, cheers
@FloweringElbow
4 жыл бұрын
Good morning Darren. Thanks for your comment. Check out some of my other vids on CS milling for this... basically it is just screwed on from the end, and a couple of places along the length. Thanks again, bongo.
@paftaf
3 жыл бұрын
Thanks for the advice on the respirator. I’m gonna buy a good one.
@FloweringElbow
3 жыл бұрын
You wont regret it :)
@paftaf
3 жыл бұрын
@@FloweringElbow I bought the Honeywell mask. Now for the cartridges I wonder if it’s better to buy the combined vapor+particulates, or attach them separately. I wonder how quickly does the filter clogs with wood dust?
@FloweringElbow
3 жыл бұрын
@@paftaf Doesn't clog super quick in my experience...
@paftaf
3 жыл бұрын
@@FloweringElbow I ordered the respirator cartridges. Looking forward to milling. My mill and ripping chain arrive next week.
@FloweringElbow
3 жыл бұрын
@@paftaf Good luck! Let us know how it goes.
@williamevans6554
5 жыл бұрын
Great video you make if look so easy .Makes me want to have a go now i have some clear instructions and a good starting point .i enjoy building sheds and tree houses from reclaimed timber as i work in a skip yard,but this is the other extreme using freshly milled timber and a welcome contrast.just subbed and will be watching more.
@JasonTheMunicipalMechanic
4 жыл бұрын
Great tips. Thank you
@FloweringElbow
4 жыл бұрын
Hey Jason, thanks for the encouragement, you're very welcome.
@marktrinitapoli6448
Жыл бұрын
Awesome❤
@harrylawrence5300
6 жыл бұрын
I’d be keen to hear your tips on sharpening chains for milling. Any tips for smaller saws? I’m only using a Chinese 62cc saw and it’s not quite man enough
@FloweringElbow
6 жыл бұрын
Only to limit the log size you attempt, not rush and possibly to try a skip tooth chain. I believe oregon does one with only about 12 cutters for a whole big 120cm bar. Not tried it though.
@miladne1092
6 жыл бұрын
do you mean that they don't use scoring tips for the ripping chain, only the standard clearing tips?
@teaneys1
4 жыл бұрын
Great tips thank you for posting
@FloweringElbow
4 жыл бұрын
Very welcome Red Dog. Thanks for commenting.
@MrCpolzin
6 жыл бұрын
Thank you so much for sharing,great tips too mate.I'm hopefully going to finish my home made mill tomorrow and cut my first trunk down into slabs.You made it look so easy so I'm feeling confident tonight.Thank you brother
@FloweringElbow
6 жыл бұрын
Best of luck friend! I hope it goes well for you. Any questions just ask.
@MrCpolzin
6 жыл бұрын
I just liked and followed you on fb.Thank you again and yes I will have questions lol.
@mawuho1566
6 жыл бұрын
I just subbed, it is real fun to watch your videos. There is a special kind of humor in them, wich I only found in channels from the UK. It´s sad that we poeple in europ are separiting in a way. Hope it stays easy to travle from and to the UK. For shure youtube will give us a great connection all over the world. Thank you for sharing and all the best from Germany ; )
@FloweringElbow
6 жыл бұрын
Ma Wu Ho thanks for the encouragement! Means a lot 2 me.
@albertpelletier4991
3 жыл бұрын
I started using an Alaska sawmill about three years ago I ended up with two different size ones because the big one (36”) is harder to control on smaller trees one thing I noticed was the coming off the log and going on the log after about the third cut it starts getting wavy on the ends I have been trying to figure how I could mount the ladder for each cut to prevent this. I saw you do it I just wish you would’ve explained a little better on how to secure the ladder for subsequent cuts without ruining the board with holes especially if you’re doing wide trees the ladder will be more in the middle therefore you’ll have screw holes in the boards
@FloweringElbow
3 жыл бұрын
Hi Albert, Thanks for your message. Sorry not to have covered that, there's only so many details one can put in these things. As you say the in and out parts of the cuts are the places where error tends to build - and has the most danger. I have found that with my ladder, after the first cut, unless things go wrong, a couple of screws in the end grain, is enough... Otherwise it's just the mills weight holding it. The mills skid is running along the log itself, so apart from some rattling, there shouldn't be any sideways forces on the ladder.... Of course if the log isn't level side to side, it's a different story. Then you have the option of biting the bullet and putting in some extra screws, or arranging some kind of other clamping system, or working on the technique required to do it without the ladder... Many options depending on circumstances. Good luck, let me know how it goes, Bongo.
@TELOYSTV
2 жыл бұрын
Sending my full support ..... ... nice work brother 👍❤️
@cdawg9149
3 жыл бұрын
Install a winch. Makes it soooooo much easier
@dethmaul
6 жыл бұрын
Great tips, great video. I love expert, field tested epiphanies. I might never have thought to shut the box to keep shit from flying in it, not until after several cuts.
@FloweringElbow
6 жыл бұрын
dethmaul haha I didn't think of it either!
@tuppybrill4915
4 ай бұрын
My only chainsaw injury so far was having ripped some slabs in a sycamore trunk (lying on the ground) by cutting vertically I proceeded to cut them free from the branching end and they fell over onto my shin!
@802louis
4 жыл бұрын
Nice job 👍
@raizt1596
7 ай бұрын
Any tips to keep the saw from lifting up or twisting as you move forward?
@FloweringElbow
7 ай бұрын
Hi there, thanks for watching. Yes lots of tips for this exact problem are in my chainsaw sharpening video. Check it out and let me know if it helps ;)
Пікірлер: 475