INDICE DEI VIDEO : davidesora.alte...
ENGLISH TRANSLATION of the written notes in the video, in order of appearance :
00:04 - Violin scroll part eighteen - Roughing of the inside of the peg box
00:15 - Before start digging refine the lines of the pegbox using some fine cut oval files, the knife and the flat scraper
00:28 - Connect harmonically the narrowing from the maximum width of the box to the nut, preserving the marks of the neck lines
01:56 - Finish the throat harmonizing the lines with the curves of the back and of the volute
02:48 - Clean the surface definitively removing all marks of the compass and the remaining scratches
03:04 - Make sure that the throat space gradually open outward without narrowing
03:14 - Keep concave the pegbox line in correspondence with the the volute, changing the direction of the curve together with the line of the back
03:26 - Mark the thickness of the upper part of the jaws (5 mm)
03:56 - Draw the end of the pegbox using the volute as a guide
04:04 - Make sure of the symmetry of jaws with respect to the center line at the nut
04:22 - Put the scroll in the vice making sure it is parallel to the plane of the bench, to have a safe and intuitive reference of verticality
04:33 - Use a drill of 5 mm in diameter, marking with tape the maximum depth for roughing, which must not exceed the lower level of the holes for the pegs
04:50 - Tilt well the drill for the first two holes, heading directly toward the G peg to keep a well inclined wall at the nut
05:14 - Always tilt the drill also towards the outside, in order to respect the increase in thickness of the walls at the box bottom (7 mm)
05:30 - Start drilling perpendicularly making a guide hole
05:37 - Tilt outward
05:52 - Perpendicular guide hole
05:57 - Tilt outward
06:07 - For holes at the end of the box dig with a gouge obtaining a plane to drill perpendicularly without slide the drill bit
06:44 - Use extreme care not to damage the volute touching it with the drill bit
06:56 - Start roughing with a flat and wide gouge cutting the links between holes
07:18 - Use a narrow gouge and very curved to eliminate more easily the excess wood
07:35 - Continue with the 22 mm chisel
08:22 - Switch to the 6 mm chisel instead of the gouge to finish the digging coming inside corners
08:36 - Isolate the entire surface of jaws to highlight the line well and prevent chipping
09:18 - Always cut strongly angled in order to respect the increase of the thickness of the walls at the bottom of the box (5 mm above, 7 mm at the bottom)
10:39 - Cut accurately the corners at the end of the box, isolating the surface of jaws to avoid tearing it accidentally
11:01 - Cut along the fiber split creating a plane to facilitate the subsequent working and determine the line of the end of the box
11:47 - Use a long-bladed knife to cut into corners unreachable with chisels and for incise the base of the walls
12:18 - Cut the terminal endgrain wall taking care to respect the inclination of the side walls
12:37 - With the 6 mm chisel cut the bottom of the box bringing it to about 3 mm below the holes for the pegs, following the curve of the back as a reference
12:55 - Trim the endgrain wall at the nut defining well the corners, leaving it though still abundant to protect the gluing surface of the nut
13:41 - With a 10 mm chisel cut the bottom underneath the G peg in the opposite direction, cutting well the sides and paying attention to the fiber split
14:01 - Check that the thickness of the bottom is close to the definitive measure but still slightly abundant (about 5.5 / 6.0 mm)
14:21 - Finish the thickness at the bottom of the walls, leaving it still abundant of about half a millimeter
15:01 - Index of videos : davidesora.alte...
15:08 - www.davidesora.it/
.
Негізгі бет 18) Testa di violino parte diciottesima - Sgrossatura della cassetta piroli
Пікірлер: 7