Putting that plate in the stock with the spring was awful, but thanks of the video helped out a lot!
@Go69
6 ай бұрын
You said it buddy.. I'm fighting it right now... i just got it in, but it was NOT as easy as he makes it seem.
@davidbarton575
Жыл бұрын
Great video, thanks so much - got me out of a jam putting it all back together again. :-)
@101evo
5 жыл бұрын
Thank you so much for doing part 1 and part 2 on this model. Just picked up a 1977 one that sat in a closet for a long time. Will clean it and go have some fun with it.
@UndertheGun
5 жыл бұрын
Have fun
@96wx3
2 ай бұрын
Same here, found a few moths in mine actually. 😆
@calebsimth4562
4 жыл бұрын
Thanks helped me with replacing my carrier assembly. I replaced it because it was jamming when trying to rack a fresh round into the chamber.
@mattiasmunkestam5663
Жыл бұрын
Thanks, this helped a lot 😃👍
@lonniedickerson9257
4 жыл бұрын
When aligning the hammer screw hole turn safety off and squeeze the trigger or you will never get it aligned.
@81gTea
Жыл бұрын
How did you get the magazine tube back into the receiver?
@UndertheGun
Жыл бұрын
Carefully.
@user-kf3ci9ih3b
6 ай бұрын
The front part to my rifle of tge barrel clamp, the holes dont align and im curious to know if the slot on the barrel and tube have to be in a perfect spot for it to screw on to
@UndertheGun
6 ай бұрын
you have to align them
@user-kf3ci9ih3b
5 ай бұрын
@UndertheGun well my barrel clamp is actually warped, had to buy a new one
@guzziguy1000
4 жыл бұрын
Good stuff, especially the part with the PROPER SCREWDRIVERS ! I was just handed an 1894 that was worked on by a gorilla with dollar store tools,smh. I'm doing a full cleaning on this and must tell my customer he needs new screws,but don't we all? lol Seriously,the proper tools make all the difference between a good job and a lousy mess.
@Go69
6 ай бұрын
Yea... that hammer spring...if you don't get it in the first 30 tries.. walk away.. bandage up your bloody fingers and come back at it later... The way I finally got it in, and it went in super easy.. instead of beating it in from the side, I simply pushed it straight in from the back towards the action and it literally popped right in. But that was an hour, and 2 beers later.. I got it within 30 seconds after pausing and then coming back to it. You CAN push it straight in.. you do not have to put it in at an angle like he is showing.
@shawnburton6839
5 жыл бұрын
Man I have a model 1893 marlin safety made in 1894. I can’t find a good breakdown manual. Do you think u could help me out. Trying to see what the gun is missing so I can restore it. Thanks.
@UndertheGun
5 жыл бұрын
numrich
@calebsimth4562
4 жыл бұрын
This video made is super easy
@josearmandomartineznieves7188
3 жыл бұрын
alguien me puede ayudar, tengo el rifle igual ke el del video, PERO ESTA FALLANDO DEL ELEVADOR, atora los cartuchos
@UndertheGun
3 жыл бұрын
Llévaselo a un herrero, no puedo decirte qué pasa sin tenerlo en mis manos.
@freddie475
5 ай бұрын
La ventanita por donde le metes la municion, posiblemente el pequeño tornillo que la detiene esta flojo.
@NULINEJIM
4 жыл бұрын
So I have a model 94 with 3 screws on the tang that holds rear stock on ( one big to the back and 2 little forward toward the hammer) I know this is an older gun but does everything breakdown and reassemble the same?
@UndertheGun
4 жыл бұрын
You sure its not a Winchester? I have a video on that one as well.
@NULINEJIM
4 жыл бұрын
@@UndertheGun It says Marlin 94 on the tang behind the hammer and you can barely makeout Marlin New Haven Conn. on barrel on left side. Cannot makeout caliber but I believe it is a .44? Put a 44 mag cartridge in it and it diddn't feed real well but did chamber. Any info you have would be greatly appreciated.. Thanks, Jim
@UndertheGun
4 жыл бұрын
@@NULINEJIM It id likely an older gun. It will disassemble more like the winchester
@stanleypost49
6 жыл бұрын
When was this gun MADE....I don't see any mention of the CROSS-BOLT-SAFETY!!!! sEEMS every 1894 video is made on OLD GUNS LACKING THIS NICE SAFETY!!!! SOMEONE PLEASE MAKE A NEW VIDEO INCLUDING THAT, if you know HOW!!!
@UndertheGun
6 жыл бұрын
I never bothered to look. The cross bolt safety models were less popular.
Пікірлер: 29