The time change Sunday was more of a strain on me than hand packing doing this same change out on my 48 survivor this morning. Nice job explaining.
@ericruiz2174
3 жыл бұрын
Just bought the bearings, thanks for sharing this video... Its a 54 chev 3100 from Puerto Rico.
@BROTHERSTruckPartsTV
3 жыл бұрын
Right on Eric! Good luck with your project!
@arielo_archivo_audiovisual
2 жыл бұрын
Great video!. Thanks i'm going to do this job in my 61 impala. Greetings from Argentina
@kirksand
4 жыл бұрын
Just what I needed to see...THANK YOU!
@BROTHERSTruckPartsTV
4 жыл бұрын
Thank you for watching!
@clydemillhaven8924
4 жыл бұрын
Just replaced the bearings in my 1951 Chevy pickup. This video was very helpful and did a great job breaking it down step by step. Also very valuable tips for getting stubborn bearing races out. Thanks for posting!
@BROTHERSTruckPartsTV
4 жыл бұрын
Very welcome, thank you for watching!
@joesheppard8000
5 жыл бұрын
Thank you. Great information!
@ericruiz2174
3 жыл бұрын
Just installed the roller bearings and the truck feels completely different. Lot of noise and vibration disapear. Thanks for the video. Everything went like shown on the video. Im not a mechanic and did it.
@BROTHERSTruckPartsTV
3 жыл бұрын
Excellent! Thanks for the feedback!
@ericruiz2174
3 жыл бұрын
@@BROTHERSTruckPartsTV feel free to share my feedback. More upgrades comming up next!
@OpieDogie
3 жыл бұрын
Excellent series of videos
@BROTHERSTruckPartsTV
3 жыл бұрын
Thank you!
@hsmcinnis
2 жыл бұрын
Great video! thanks.
@BROTHERSTruckPartsTV
2 жыл бұрын
You're welcome!
@jerryloughmiller3283
4 ай бұрын
Real good video. Thanks a lot.
@antonjohnson-mr5yk
4 ай бұрын
The camera sometimes follows the teacher instead of looking at what he is doing and dosen't zoom in on the work enough, and misses a step.
@bobsmith-hd2hi
2 жыл бұрын
hand packing bearings is the only way
@joaquinhire7163
4 жыл бұрын
It's much easier to install new races if you put your new ones in the freezer over night.
@BROTHERSTruckPartsTV
4 жыл бұрын
Excellent tip!
@jhmerit8883
3 жыл бұрын
Also you can leave the hub out in the Sun or in an oven.
@fiddlerpin
2 жыл бұрын
Using the old race to install the new race is good but you should grind the outside slightly smaller or they will get stuck.
@juliettedauterive3745
7 ай бұрын
You don’ t have a flat piece of steel plate 4- 6” you can put on top of the races and tap on that?
@ncgregburnsed6621
2 жыл бұрын
David, great video. Is there a disc brake conversion for 1956 3600 chevy truck I have the 8 lug wheels on all four?
@BROTHERSTruckPartsTV
2 жыл бұрын
Call our shop and one of the Techs will give you a run down of options. 800-977-2767
@rubenrangel137
3 жыл бұрын
Can you do that to a 1950 Chevy truck 3600 series on the rear
@BROTHERSTruckPartsTV
3 жыл бұрын
There's no kit available for the rear.
@Oldcarnut63
27 күн бұрын
Dumb question why is the spindle nut washer made not to spin?
@michaelzeni4570
2 жыл бұрын
I started this upgrade while swapping to disc brakes in my 53 chevy. Everything went great for the passenger side. Started the drivers side and the inner bearing (larger of the 2) won't go all the way onto the spindle. It fits into the hub just fine, but when I go to put the entire assembly onto the spindle it stops about an inch from where it should. The bearing got really stuck on there too, it took me quite a while to get it off. Any ideas on what I am doing wrong?
@BROTHERSTruckPartsTV
2 жыл бұрын
Some photos would help. Can you contact our office, they'll give you a number to text photos to and one of the techs will help sort it out. Did you buy the bearing set from us? If so, they'll be able to look up what we sent you too which can be helpful.
@MrNoNameThanks
3 жыл бұрын
I’m in the UK we have this same truck with front wheel bearing issues that’s had a disc conversion…. Any chance you could help? If you reply I will forward the questions I need to ask, thank you.
@BROTHERSTruckPartsTV
3 жыл бұрын
You're best bet is to contact customer service, we don't do tech help via KZitem comments. Email orders@brotherstrucks.com or call us at 951-808-9790.
@dragonrider7366
2 жыл бұрын
Is there a specific way to remove the inner race if it stuck? I am having a lot of trouble trying to get it off(57 Chevy 3100)
@BROTHERSTruckPartsTV
2 жыл бұрын
You can try heating it with a torch or you can cut it off. If you cut it be really careful not to damage the spindle.
@1icky
Жыл бұрын
Does this upgrade come as a paired kit or have to purchase separately twice? What is the parts number I need?
@claytonfreeman5067
4 жыл бұрын
just starting on 64 gmc 930 1ton those dust caps arent easy . after seeing this ill have to do bearings to .the info from here will make things a little easy,er
@BROTHERSTruckPartsTV
4 жыл бұрын
Thanks man, good luck!
@garyhelms1889
3 жыл бұрын
ONE question- After you installed the front and rear race, bearings and seal you proceeded to put the hub back on the spindle, but what exactly holds that round plate (about 3 inches in diameter on the spindle) in place after assembled. It that was left in place the whole video. It seems it would be loose and rub the brake plate or the hub when the wheel is spinning. Good video overall and THANKS for the videos. I just purchased a 54 chevy truck and already have placed an order with Brothers truck parts.
@BROTHERSTruckPartsTV
3 жыл бұрын
That is kind of a "dust cover" and it's spot welded to the backing plate.
@garyhelms1889
3 жыл бұрын
@@BROTHERSTruckPartsTV if you watch the video from time 5:13 to about 5:40 you'll see David cleaning the spindle. That plate is flopping around. Possibly the spot weld broke and he just didn't notice or for sake of the video just kept moving. But it appears that plate would be rubbing once assembled. I'm not a mecahnic, so every detail is something I cling too. I'm learning!!!!!
@garyhelms1889
3 жыл бұрын
@@BROTHERSTruckPartsTV Side note to other comment. I don't even have that plate on my brake back plate. I am currently working on my brakes. My pad liner fell off the brake shoe while driving the truck home from actually buying the truck. Pad chewed up the inside of the drum of course.
@BROTHERSTruckPartsTV
3 жыл бұрын
@@garyhelms1889 Ok, we see what you're talking about, still it's just a dust cover. If yours is missing it's not a big deal, just assemble it without.
@scoutman6651
3 жыл бұрын
@@BROTHERSTruckPartsTV No,,,,,that coveris not welded to the backing plate, nor is it supposed to be. I have the same question and am currently waiting on a response from Brothers as to whether or not to use it at all.
@christineshipley4081
Жыл бұрын
Is anyone carrying a tapered roller bearing kit for a GMC 3/4 ton pick up yet?
@markmcdermott8307
3 жыл бұрын
Greetings. Does anyone know if the bearings for my 1948 chevy 1 ton, 8 lug, are the same size as the the 3100 1/2 ton, 6 lug version? My front bearing is making the classic sounds of wanting upgraded and this is the first time doing "huck brakes". My 5 window gets so much attention and everyone loves the "rusty look"! Ha ha! Take care!
@BROTHERSTruckPartsTV
3 жыл бұрын
They are not the same. You could probably put together a set from available bearings and the proper measuring devices, but a buy and install kit is not available.
@markmcdermott8307
3 жыл бұрын
@@BROTHERSTruckPartsTV Thankyou for the tip! I had a feeling they were different.
@bambichadwick1100
Жыл бұрын
my truck won't roll. it is only for esthetic. No motor but has been sitting still for about 1 year and I can't get it to roll. any ideas?
@jamesberdine8574
6 ай бұрын
Remove the break drums. If the drum won’t come off draw in the shoes by turning the adjustment star.
@nogonova
Жыл бұрын
Will this work for a 1960 c10
@BROTHERSTruckPartsTV
Жыл бұрын
No sir
@nogonova
Жыл бұрын
@@BROTHERSTruckPartsTV so disc brakes it is.
@BROTHERSTruckPartsTV
Жыл бұрын
@@nogonova Yep
@stephaniegeorge8800
4 жыл бұрын
Hi David . I’m about to do a disc brake conversion with the Brothers Deluxe conversion kit and I also purchased the inner and outer ball bearing upgrade. I’m having a problem removing what seem to be the bearing . What do you suggest I’ve tried everything and it seems to be stuck on the wheel itself. I’d like to send a photo but don’t see where I can attach it.
@BROTHERSTruckPartsTV
4 жыл бұрын
Alex from our Customer Service Dept is going to contact you and give you a number you can text photos to. If you DO NOT hear from him within 24 hours it means we couldn't find your account and contact info, please call us at 800-977-2767 if that happens.
Пікірлер: 57