Excellent video! Now if you could just come over and tinker with my 68 camaro I'd really be happy!
@EdGieder
Жыл бұрын
Much appreciated.great video. Window installation went well.
@DM2006800
10 жыл бұрын
Your video's have been very helpful. Appreciate it, keep up the good work. 67' Firebird 400, 4 speed.
@sheldonport4218
3 жыл бұрын
You need to show the stops, and their adjustments for the window height. Don't assume everyone automatically knows where and what you're talking about. Thanks.
@kaylarapozo162
2 жыл бұрын
Very good video I felt like my dad talking
@marcusbartl5369
7 жыл бұрын
this helps me perfectly thanks for the instructions greetings from Germany Berlin
@papadent5803
7 жыл бұрын
Great News! Thank You
@davidmorrison5200
8 жыл бұрын
Helpful for my 66 Cutlass. Thank you.
@mwmantha1234
8 жыл бұрын
Thanks for your help today figuring out what the door stop was and aligning the window. hahahaha!
@MrScaredshiftless
8 жыл бұрын
No Problem! Any time. Thank You
@Motown454
9 жыл бұрын
Thanks this is great help for when I put mine in .
@nancyhoralia
10 жыл бұрын
I learned a lot today.Thank you
@kennwierenga3126
2 жыл бұрын
THANK YOU !!
@guillermoflores2857
6 жыл бұрын
Everything you said and did was very helpful , the only thing you didn't show was the part that I needed the most, where are the front and rear stops located?
@philsanchez7100
3 жыл бұрын
Thanks dude you rock
@giovannikrasniqi5138
7 жыл бұрын
hi mark were is the video to adjust the rear window thanks
@anthonynoland2593
5 жыл бұрын
I have a 67 firebird 326 H.O and i was wondering how do you replace the front door panels and the weather stripping
@kennethmogensen5975
8 жыл бұрын
thanks for the help :-)
@justanother67camaro32
3 жыл бұрын
Mark Boice do you have an actual video of mounting the glass into the new rubber and brackets? Before the complete assembly goes into the door and the same goes for quarter windows.
@ArrowheadGarage
Жыл бұрын
Thats the same issue I am having on my 67 Firebird
@justanother67camaro32
Жыл бұрын
@@ArrowheadGarage I ended up finding another video that had similar windows and it worked in the end. I used a good sized mallet, glass cleaner to lubricate everything and good amount of force to get everything to seat -it took about double the force I was comfortable with. Take measurements of where the bracket is located on the glass and do the work on a blanket folded over, helps with the shock form the hammer. Caution with metal bracket, there's a thin spot and it'll bend fairly easy if you don't have something about 6-8" long (maybe a 2x4...) between it and the mallet. I still have the original rubber that came if you're interested, they're in great shape and kinda wished I used them instead of the material I went with.
@6t8camaro3
7 жыл бұрын
Great videos Mark. I have a question pertaining to the door windows on a 68 Camaro. My widows roll up and down smoothly, rattle horribly no matter if they a rolled down a 1/2" or all the way. What would you recommend I adjust or replace? Do you have a video for this specific issue? Also what is the best way to remove the door panel? Thanks in advance for any help
@crsp76691
9 жыл бұрын
Can you do this same video on a 68? Im having a bear of a time! Thanks for the vid though, it still helped
@thane411
8 жыл бұрын
Hi Mark! Any tips to get my 67 camaro door lined up? When I try to move the back of the door up, I can't nail the height. I either end up 1/8" to high or too low. Is there a way to loosen the hinges and tap them up with a hammer? Thanks for your help and videos.
@MrScaredshiftless
8 жыл бұрын
+Thane White To align the front doors on Most GM cars is simple but really not unless you have the front fenders off. The bolts for the front hinges are behind the fender and hard to get to to loosen or tighten properly. We use stir sticks taped to the lower edge on the rocker that area about 3/16 thick to hold the door up to start with. The same is used at the back of the door one near the top and another near the bottom. Then we align the angles. Without having access to the bolts behind the fenders it may be difficult. Hope this is helpful. Thank You
@MidnightRunCreations
11 жыл бұрын
yeah but how do you install the tracks they go in???????????
@thomaswild9044
7 жыл бұрын
Greetings, Excellent video. I have to install all the side windows in a 65 GTO, any tips in tackling it the right way?
@MrScaredshiftless
7 жыл бұрын
For some reason the right side always goes better than the drivers side. Start there first. Vent window, Door Glass, Quarter glass. Makes sure everything is clean of dirt and debris. Do not be afraid of to much grease. You can always wipe off later. Thank You
@tomcarter6804
2 жыл бұрын
Hi, I can't find part 1...??
@giovannikrasniqi5138
7 жыл бұрын
hi mark my rear roll down window and drivers window is out of adjustment, what glass should i start with to adjust thank you
@MrScaredshiftless
7 жыл бұрын
Start with the front door glass. Make sure it fits nice to the pillar. Then go to the rear glass. Then you can make final adjustments from there. Thank You
@roberttallman3352
10 жыл бұрын
what happened to part 1 ????
@jimkojak5554
5 жыл бұрын
Do you have a video of removing front window Thanks
@MrScaredshiftless
5 жыл бұрын
Sorry, Not for the 67. Thank You Mark
@stevemoore6573
4 жыл бұрын
Have you ever changed a 67 to to a 68 ? I have 67 and want to do away with vents
@MrScaredshiftless
4 жыл бұрын
We have not done that before. However seems like a simple conversion.
@giovannikrasniqi5138
7 жыл бұрын
hi mark. i have 67 camaro the rear passanger side is higher then the left side . i measured top of tire to edge of wheel right side 5 1/2 inche drivers side 2 1/2. what do u think is the problem. thanks for any help
@papadent5803
7 жыл бұрын
First you will need to check for body damage in the rear where the leaf springs attach. If all looks good you probably have a weak leaf spring in the rear or weak coil spring in the front suspension. Measure the ride height from side to side. Then we can dial in a problem. Thank You for your question.
@giovannikrasniqi5138
7 жыл бұрын
Thank you for your reply. There are no signs of damage and also i did replace both leaf springs. So it must me front spring. Also i noticed my wheel well in engine compartment was not sacured to left fender
@vlineguy
8 жыл бұрын
how do you replace the roller
@ClassicCarGaming
8 жыл бұрын
You will have to drill out the small rivet and replace it. Simple task! Get the parts first! Thank you
@xXSPITZENXx
8 жыл бұрын
now I do mine
@MrScaredshiftless
8 жыл бұрын
+xXSPITZENXx You will do just fine!
@xXSPITZENXx
8 жыл бұрын
+Mark Boice I did Mark =)
@luizchevelle7218
8 жыл бұрын
Is this procedure the same for the 67 Camaro?
@luizchevelle7218
8 жыл бұрын
+Luiz Chevelle You answered in the end of the video!
@MrScaredshiftless
8 жыл бұрын
+Luiz Chevelle It is the same for 67,68,69 Camaro and Firebird. Thank You
@MrScaredshiftless
8 жыл бұрын
+Mark Boice 67 Camaro and Firebird. With vent windows.
@luizchevelle7218
8 жыл бұрын
+Mark Boice Just like my 67 RS 327 coupe.
@papadent5803
7 жыл бұрын
No it will be completely different. There is a Camaro glass adjustment video posted. Thank You
Пікірлер: 54