I just recently found your channel and literally binge watched all your videos in the past few days. I just acquired a 67 Camaro that has been butchered. I like what you have been doing. It gives me a lot of inspiration on my future project. I need to get her running first and enjoy it a bit. Also need a garage to do something in…. Look forward to all your future progress. Keep up the good work!
@ElrodsGarage
Жыл бұрын
Thanks a bunch! Welcome to the party. Best of luck with your '67 Camaro project!
@Kyle_Nelson
Жыл бұрын
Thanks for not being afraid to show your errors, that's how we all learn!
@stevencoughran6115
6 ай бұрын
Nice project,good info really nice video, I just need to paint my 68 camaro love to see more
@ElrodsGarage
6 ай бұрын
Thanks a bunch. I can't wait to get back to work on this project.
@perrywe1
Жыл бұрын
nice work. panel looks killer!
@kaklspatz1944
Жыл бұрын
Don't give up it's looking great
@MrFireman164
Жыл бұрын
Nice work, I may change my mind but I plan on silicone bronzing those areas
@ElrodsGarage
Жыл бұрын
That sounds like a good idea. I look forward to seeing it. Thanks a bunch!
@ParadiseBayCustoms
Жыл бұрын
Looks like a bit of a bear no? Fine job! 👍
@ElrodsGarage
Жыл бұрын
It wasn't too bad. I'm just glad the AMD panel fit wo well.
@GoGoGarage
Жыл бұрын
These cars are like onions. Coming along and I ended up welding those edges. Not only did I spot weld it in, but I also used two part 3M Epoxy Metal bonding in between the seams.
@ElrodsGarage
Жыл бұрын
These cars are like onions, They stink, they make you cry, and if you leave them out in the sun they get all brown and start sprouting little white hairs. ~ Shrek I just watched your video. (I need to binge your channel) I like how you attached the filler panel before the package tray. I saw you using a pinch welder. How does it work for you? I bought one and it didn't like welding rusty old metal. Keep up the good work!
@GoGoGarage
Жыл бұрын
@@ElrodsGarage for small simple stuff that welder worked fine, just not for areas that I felt needed to be strong.
@ElrodsGarage
Жыл бұрын
@@GoGoGarage That's how I felt too. I want to use it on other projects to see how it does. I just don't trust it on the Camaro.
@Jim-hv6ql
8 ай бұрын
Your video on this brings back memories. I also replaced my truck filler panel with AMD and had to incorporate the same modifications to fit. In addition, I had to cut and raise the area between the filler panel and truck. With regards to the bottom window area. I have left that open. In fact, I drilled out a small drain hole. I have been thinking about adding a small tube (about 1 inch) to the inside. Then if in the future I could attach a plastic tube and run that to the bottom of the quarter panel when required.
@aMAYSingMetalWorks
8 ай бұрын
Nice work.
@ElrodsGarage
7 ай бұрын
Thanks a bunch Jubee!
@autometaldirect
Жыл бұрын
Nice work! Looks good.
@jcook69camaro
Жыл бұрын
gm put seam sealer in the bottom corners. but this is the reason the trunk pans rust out. I welded mine solid ground it down flat then put seam sealer. I did the same thing on the lower part of the filler panel where you added the small piece of metal.
@woodchipgarage
Жыл бұрын
Wow, that must've been a common after market "repair". At some point in its life, my rear deck filler panel ended up being reinstalled in a similar fashion. I always wondered if it was actually supposed to be welded on the outside like that. I never knew, but it just looks wrong. Thank you for pointing that out.
@ElrodsGarage
Жыл бұрын
Yeah, water gathers around the back glass and rots out this panel. And I can imagine anyone replacing this panel doesn't want to stand on their head to try and weld it in. I have seen where guys weld up the whole seam.
Пікірлер: 23