man im glad you got this video up even know its from 2018 i still go back an look see just picked up a 1982 rude 15hp
@THISOLDOUTBOARD1
3 жыл бұрын
Hey. Thanks for tuning in. This video is "from the Archives" section on my channel. It was shot in 2014 but wasn't uploaded until 2018. Thanks again & Stay tuned !
@collinschubert6940
Жыл бұрын
There is a nice man who speaks to my left ear when I watch this video.
@THISOLDOUTBOARD1
Жыл бұрын
What's his name?
@801Outdoors
6 жыл бұрын
Excellent job,,,I plan to paint my evenrude as soon as I find time to get a water pump and starter in it
@THISOLDOUTBOARD1
6 жыл бұрын
kool, cant wait to c it
@rustyedmoore
6 жыл бұрын
Look 107 subs, You are flying...Keep it up!
@THISOLDOUTBOARD1
6 жыл бұрын
109. but whose counting. hahaha
@gsallen9588
6 жыл бұрын
Another sweet hummin' success. May day build. Sound marketing, so to speak. How long do you have to wait before submerging new paint?
@THISOLDOUTBOARD1
6 жыл бұрын
you know what, I never really thought about it. But, I'm sure it wasn't the same day, by the time the paint was dry and putting it back together, had to be a couple/few days by the time I got it in the water.
@laserlars345
2 ай бұрын
I have a 74 15hp evinrude. It cranks up every once in a while for a few seconds. I messed with the lean/rich dial, the choke and the throttle but I can’t get it to keep running. New spark plugs. What do you suggest? Do you think I should take out the carburetor and clean it properly?
@THISOLDOUTBOARD1
2 ай бұрын
Hey. Thanks for tuning in! Hell yeah! The carb needs to be surgically clean! Check out my Carb Cleaning video, "The two most important things". A new fuel pump would be good too! Cheap on ebay! Thanks again & Stay Tuned !
@josephmiller9756
Жыл бұрын
I have the same motor the carb is all brand new parts I don't really good but will not go full speed what do you think
@THISOLDOUTBOARD1
Жыл бұрын
Hey. Thanks for tuning in. Make sure it's running on both cylinders. High speed orifice/jet needs to be surgically clean. Points clean or new and set to proper gap. Condensers new. Coils ? Carb & timing set. Cam follower/roller opening at full throttle. Try running it on one cylinder at a time, that will help trank things down if just one cylinder is giving you problems. Does it have good compression? You just have to pick at it until you find the problem.
@victorremick9721
5 жыл бұрын
I LIKE THE GRAINY VIDEOS LOOK VINTAGE
@THISOLDOUTBOARD1
4 жыл бұрын
Yeah these were all shot on a little kodak pocket camera 2012-2013 not really that long ago. Its amazing how much technology has come along in the past 5 years. Now you can shoot an entire movie on a phone !
@matthawkins8190
6 жыл бұрын
Recently purchased 1974 15hp No spark on arrival - Found key half warn into shaft. Is it a split key ? Can I put heat to the shaft without issues ?
@THISOLDOUTBOARD1
6 жыл бұрын
HEY. it's a half moon key, dont do heat unless you plan on replacing the upper crank shaft seal. ALSO, check the groove in the flywheel for ware and tare, if its not ''tight'' the motor wont run right, the timing will be off. it sounds like the groove in the flywheel is worn. www.marineengine.com/parts/johnson-evinrude-parts.php?year=1974&hp=15&model=15455S&manufacturer=Evinrude§ion=Crankshaft+And+Piston. ALSO, Check out www.leeroysramblings.com/ . there is an article that tells you how to fix the grove in the flywheel, plus everything else you ever need to KNOW , let me know how it goes. thanks
@matthawkins8190
6 жыл бұрын
THIS OLD OUTBOARD - I see the half moon in the break down - flywheel cover looks in decent shape . Need to get the woodruff key out or we fish from shore ! Great help thanks for the incite
@THISOLDOUTBOARD1
6 жыл бұрын
try and tap it out. whats a flywheel cover???
@matthawkins8190
6 жыл бұрын
THIS OLD OUTBOARD . Once I took the flywheel off , I should have given you more info
@THISOLDOUTBOARD1
6 жыл бұрын
👍, Have fun guys. thx again
@lukebray2192
4 жыл бұрын
Need to change the impeller on my 9.5 sport win but the driveshaft is stuck in the crank (top). Any suggestions on how to break it loose?
@THISOLDOUTBOARD1
4 жыл бұрын
Hey. One guy told me he hung it upside down from a tree and sprayed it with PB Blaster and somehow finally got it to drop. You can try and cut a couple of wood wedges and tap them in between the gearcase and mid section. The only thing holding the gearcase on is the pin for the impeller on the drive shaft. Sometimes the pin will bend or break through the pump and the gearcase will come off giving you more access to the drive shaft. With more access to the shaft you can put some vice grips on it and try to tap it out. Good luck!
@lukebray2192
4 жыл бұрын
THIS OLD OUTBOARD I have the water pump housing and lower unit already off of the drive shaft. I can’t get it to come loose from the crank or power headset the top.
@THISOLDOUTBOARD1
4 жыл бұрын
@@lukebray2192 Ok. Turn it upside down and shoot some Pb Blaster in it and let it soak for a couple days. Clamp some vice grips on it and try and tap it out. It may take a week!
@HarryBungholio
4 жыл бұрын
Do these motors pee out a stream? Mine barely spits out a mist from the exhaust.
@THISOLDOUTBOARD1
4 жыл бұрын
Yes Sounds like you need a new water pump impeller and/or thermostat. If all your seeing is steam Do Not run it. You can burn it up! Everything you need to know is here www.leeroysramblings.com/Outboard%20Motor%20Related/OMC%20outboard%20related%20articles.html
@lilhawk6663
6 жыл бұрын
Me and my dad just bought a boat and it has the same exact motor but a 74 it won’t start the spark plugs brand new won’t start
@THISOLDOUTBOARD1
6 жыл бұрын
HEY. Thanks for checking out my video and subscribing to my channel 👍. First of all did you check the compression on the cylinders, if its good your half way there! If its on the low side dont start buying parts for it unless your going to tear it down and rebuild it. Would be a Great father/son project. NO spark! UT-O, start by pulling off the flywheel and checking your ignition components. Heres a great place to learn everything you need to know. www.leeroysramblings.com/ . Check it out and let me know how its going. Stay Tuned and Thanks again !
@pescarfishing8685
5 жыл бұрын
Very nice! I have the same motor, I don’t know how to adjust the rich and lean, can you explain to me please?
@THISOLDOUTBOARD1
5 жыл бұрын
Hey. Set the needle at 1.5 turns out from gently seated. Start the motor let it warm up. Slowly turn the needle in clockwise about 1/8 of a turn each time, give the motor time to adjust on each turn. once you hear the motor start to ''sneeze'' or ''cough'' turn the needle back 1/4 of a turn. your sweet spot should be in that range. Thats the basic steps, after you get it on the water put it in gear at idle and dial it in to a nice smooth idle. Not all carbs are the same but you should be close to that range if everything else is in spec. Thanks . Stay tuned !
@pescarfishing8685
5 жыл бұрын
Thank you! I will try this soon!
@THISOLDOUTBOARD1
5 жыл бұрын
@@pescarfishing8685 Also check out Leeroys. 15 hp section, everything you ever need to know ! thx www.leeroysramblings.com/index.html
@tonybruno7848
6 жыл бұрын
How do you find paint at the auto parts that comes close the the original color? The selection at the parts stores is a joke around here.
@THISOLDOUTBOARD1
6 жыл бұрын
i got the paint from O'Reilly's auto parts, the color is called metallic blue engine paint. i think its around 8 bucs a can. i was just checking their paint selection one day and thought it looked good and bing bang boom!
Пікірлер: 38