That first guy working on the Mustang looks like he is ready for a Busch Light
@mach275
7 ай бұрын
I give this 7.5/10 still good video ! I’ve been struggling with mine for months now. I’ll need to bleed it from the top bleeder valve. I hope that gives me the last push of the tob to get it into 1st gear.
@M91211
4 жыл бұрын
Price is around 650$ ouch!! I'll get a lifetime worth of adjustable clutch cable with that kinda of price lol
@shootthemoon9549
4 жыл бұрын
I want to do the conversion but this thing looks like the slave and master cylinder are gonna be flopping around when the clutch is released.
@krpelkey
12 жыл бұрын
i thought u said no more bleeding
@i_sniff_blue9569
5 жыл бұрын
^^ THIS. Every time I even think about touching the clutch linkage I keep thinking I've done something wrong when really this kit just requires bleeding for DAYS.
@aleksvillalobos8525
2 жыл бұрын
Update this video please there is no information anywhere about the internal mounting of the Throw out bearing. Does it just float inside the bell housing on the input shaft? I’m curious how it just “replaces” the stock bearing when the bearing was held in place by a clutch fork.
@ShaunPC
10 жыл бұрын
What is the travel in inches of the internal throw out bearing?
@Anlushac11
11 жыл бұрын
Same here. I was hoping for more on how to install the internal release kit. Mine is going on a 85 Mustang coupe with turbocharged inline six. Since its go a return line Im guessing any air bubbles get passed through return line back up to bleeder.
@MrDannycoutin
8 жыл бұрын
some one missed the throw out bearing lol
@flyhouseoftruth470
5 жыл бұрын
Will this work in a 1991 Ford Ranger "S" with a 1995 Mustang GT engine and 5speed transmission in it?
@Ranjithog_YT
4 ай бұрын
Hey I installed the clutch onto my mustang and when I clutch I have no pressure, do you have any suggestions, it’s not pulling on the clutch fork under the car. It just sits still.
@McLeodRacingClutches
4 ай бұрын
If nothing is moving, then you still have air in the system. You need to continue to bleed the system until the clutch pedal has the same pedal feel as the brake pedal.
@hunchotroy2759
3 жыл бұрын
If even possible is “dropping the clutch” any more destructive to the hydraulic clutch (with hydraulic bearing) than a conventional clutch cable and fork? Also does the pedal slowly return upwards after being pressed ?
@wyntifurlust6480
5 жыл бұрын
I got one of they’re clutch kit and the throw out bearing didn’t last me 6 months
@McLeodRacingClutches
5 жыл бұрын
wyntifur lust hello! What happened with the bearing?
@htkuntamed1989
5 жыл бұрын
What happened I’m thinking of buying one but I keep hearing bad things about it leaking
@McLeodRacingClutches
5 жыл бұрын
gavino orozco what kind of car do you have?
@wyntifurlust6480
5 жыл бұрын
gavino orozco throw out bearing didn’t last I’ve been asking around and people have recommended to go with the stock bearing, as far as hydraulic quality I could not input since my mustang gt is cable operated
@wyntifurlust6480
5 жыл бұрын
McLeodRacingClutches when I removed the bearing attempt to spin it to verify that is what failed in the clutch system and the bearing would just grinding I kept all the parts except the old flywheel and pilot bearing since the pilot bearing was in pieces attempting to removing and since I got a new flywheel , reverted the pressures plate and clutch and bearing back to ford stock parts since my dealer still had those parts
@ethanmyers1661
3 жыл бұрын
Does this work with tremec transmission?
@rdy2run332
3 жыл бұрын
Is it ok to use this kit with long tube headers?
@MrDavidelliottjr
12 жыл бұрын
i want to install this in my 98 but i installed a tr3650.. will it work and i have a after marker f1 stage 3 clutch kit set up. and i want to put the internal slave.. will this set up work? if not what set up will work mcload racing?
@michaelgardner122
10 жыл бұрын
What is the part number for the external slave cylinder set up. I can not find it on your web page. Also price would be great. Thanks
@McLeodRacingClutches
10 жыл бұрын
The part number is 14-326. It is located at www.mcleodracing.com } Hydraulics } Hydraulic Conversion Kits.
@justanotherengine
11 жыл бұрын
I have a 347 stroker and a 9# Powerdyne s/c. I keep cooking clutch cables (6) between the header tubes, they stretch and break and leave me stranded ( while the cable is UN-stranded). I'm hoping this kit ends all of that !
@easycomeeasygo8901
5 жыл бұрын
Did you ever install this how did you make out?
@htkuntamed1989
5 жыл бұрын
Did you end up putting it on
@i_sniff_blue9569
5 жыл бұрын
@@htkuntamed1989 I have the throw-out bearing version of this kit, and it definitely helps if you're headers cook your cables. Haven't had a heat-related clutch incident since the swap, plus you can route the fluid line pretty much wherever if you're willing to get some clamps/zip-ties or route some hardline. That said, be prepared to bleed this thing about as much as you saw in this video, it takes commitment lol.
@cwilliams9854
8 жыл бұрын
Why don't you show how to install the quadrant. Even the kit instructions don't show anything about the quadrant and to picture is lame. Nowhere does it say that there are 2 posts for the quadrant. You assume everyone knows how the clutch pedal assembly works, not user friendly. How do you connect the cable when you have only space for one hand and no leverage to pull the cable over the quadrant. if the unit has fluid, there is noway someone will pull the cable to attach it to the quadrant. All of your instructions are really bad and unfriendly.
@johndoe-zb8bm
4 жыл бұрын
Because they know its more difficult than they claim. Look how the install kicked his butt just pushing it through the hole. It doesn't mount to anything. Looks like a $650.00 dollar paper weight in my opinion. .I'll go with his competitor. Looks like better set up.
@danielserrano8600
3 жыл бұрын
Link for the kit?!?
@McLeodRacingClutches
3 жыл бұрын
www.mcleodracing.com/conversion-kits-ford/p89
@danielserrano8600
3 жыл бұрын
@@McLeodRacingClutches thank youu sir im ordering one right now
@1Jomarcel
5 жыл бұрын
Clumsy
@checkmate22
3 жыл бұрын
look like you guys took a "smoke break" and just ended the dame video. Smdh wtf was that??
@McLeodRacingClutches
3 жыл бұрын
Do you have another question for the kits?
@McLeodRacingClutches
11 жыл бұрын
Craig give us a call at 714 630 3668 Monday thru Friday and we'll be more than happy to walk you through the proper way to bleed your system.
@Revenants_Prophecy
4 жыл бұрын
this looks like it was filmed with a potato
@McLeodRacingClutches
4 жыл бұрын
Maybe we did....
@johndoe-zb8bm
4 жыл бұрын
@@McLeodRacingClutches Great way to promote your business 👏
@renemeza1000
13 жыл бұрын
oooou a supercharge stang
@maddogg26
4 жыл бұрын
Man you said throw out bearing also wtf where is that shit at
@TurboTurdBurglar
3 жыл бұрын
Damn you guys really be milking the price. Should be like $200 😂
@BurnTiresNotDrugs
10 жыл бұрын
uhh $580..ill pass
@DavidQuintana17
3 жыл бұрын
fax
@Tommyboy56
4 жыл бұрын
I want to buy one of these so bad but this install video is terrible. Blocking the camera when showing how to attach the slave cylinder. Doesn't show the interior hookup or quadrant install. And they give you one page horrible instructions. I'm worried about spending this much and then not being to install it. Should be better instructions and video for $600.
@McLeodRacingClutches
4 жыл бұрын
Hey there! If you need more instructions, be sure to give our tech line a call! They can help install the kit. Thanks! 714-630-2764
@Tommyboy56
4 жыл бұрын
@@McLeodRacingClutches Thank you, I will call. Definitely have questions about the install. I appreciate the response.
Пікірлер: 53