What a magnificent Johnson! The 521 cc sounds great! Grew up with a 1966 6 hp and a 1977 25 hp! 😀
@mattbolanz1216
2 жыл бұрын
this is my favorite video of yours because it sounds exactly like the 1984 30 hp johnson my dad had on a 13 foot tri hull growing up. brings back lots of memories
@theeasybeats5913
10 жыл бұрын
Very nice motor, old memories of old Johnsons and Evinrudes
@matthewowens455
6 жыл бұрын
Runs like a charm
@chirskov
2 жыл бұрын
Hello! Thank you so much for your video. I own the same Johnson 35 hp with remote control. Greetings from Russia, the Coast of Ladoga Lake.
@famasmaster2000
7 жыл бұрын
You know what the funny part is ? Pepper has no clue she was going mach 1 ......pepper is so cute and trusting. We still love her in these vids ! How is pepper doing ?? Great motor vid too by the way. She is a smooth runner
@johny2535
12 жыл бұрын
The intake manifolds are different also. The 20, 25, and 30 in 1993 all had different intakes
@kennsaunders1690
7 жыл бұрын
1st time I have seen Pepper in your videos.
@chrysleroutboarddude
12 жыл бұрын
@Doghouse594 The 1989 Lund s14 is rated at 35hp and the boat has no problem with 35hp.And he only Difference between the 30hp and the 1993 20hp Evinrude is the hi speed jet in the carburetor.Look it up in the parts book.You should see it when i put 2 35s on it
@bearscubs6994
5 жыл бұрын
Hello Great video!! How much does a motor this size sell for I'm currently in the market for 25-35hp Long shaft and I'm selling my 1974 15bp long shaft Thanks for any advice!! Btw that motor was flying and sounded really nice!!
@therealeeeo
11 жыл бұрын
Unfortunately I've got other issues as well. I had it running and idling well at home in drum of water but I just had it out on Owasso yesterday for a test run and it would idle, but as I opened it up it would bog down and want to stall unless I choked it. After 8 years of storage I think the carb needs a kit and possibly a fuel pump kit too. Hardly anyone around the cities works on these old outboards anymore.
@chrysleroutboarddude
12 жыл бұрын
Yes on a lot of motor's you cannot get more hp with just a carb swap.You will not get 15hp out of a 9.9 for the reasons that you stated.But on the omc 1984-1999 25-35hp have the same part# for the exhaust tuner,intake manifold,reed valve's,engine block,piston's,crankshaft,con rod's.And on some years the only part# that is different is the hi speed jet in the carb.The 20hp has a different intake manifold and carb but the exhaust tuner is the same.So yes you can make a 35 in stock form out of a 20
@jacquischinzig7049
4 жыл бұрын
Hi chrysleroutboarddude! I have just inherited a little fibreglass boat from my Grandad with an 1984 30hp Johnson (J30ELCRR). Do you know if this info about the hi speed jet would apply to this engine? Thanks!
@michaelwall1166
7 жыл бұрын
it pumps water really good
@bluegrassak7445
4 жыл бұрын
I just bought this exact motor, did a compression test, it reads 165psi ! Is this cause for concern? Also, what should the idle rpm be set at?
@bearscubs6994
5 жыл бұрын
Wow love this motor sounds very good!!! My question is do you have the motors for sale? Thanks
@therealeeeo
11 жыл бұрын
I don't think it runs hot, but I'm not sure how I'd tell. I might try taking the hose off and seeing if that's the issue. At this point it's nothing but an regular drip, definitely not a steady stream. I do get a good amount of water out of the exhaust holes though.
@chrysleroutboarddude
11 жыл бұрын
Yep sounds like a carb problem. What city are you in?
@WarthDader74
10 жыл бұрын
Go front......go front.......that's a nice dog :-)
@chrysleroutboarddude
10 жыл бұрын
Yea She is a wonderful friend..
@tylerhoneycutt8055
3 жыл бұрын
I have the same motor. J35RCRR. Wont run unless some fuel mixture is sprayed inside the carb. Fuel pump is pumping and fuel is in the carb. Carb has been rebuilt with almost surgery like cleanliness and fuel pump is new and have verified it pumping. I’m at a loss. Any advice would be great. Thanks
@christiangrech1375
11 жыл бұрын
I currently own a 17 feet fishing boat with a 35 hp Johnson outboard, will it hit 25 knots? Thanks in advance
@tophatvideosinc.5858
Жыл бұрын
Man, my '73 seahorse 35 must nit be doing good if this is how fast a 14 footer is supposed to go with it. I was hitting 15mph tops. How much would it be to get one repaired or just serviced? Got the boat, trailer and engine for a total of 200 bucks.
@chrysleroutboarddude
11 жыл бұрын
It should have a good strong stream from the tell tale and out of the exhaust relief holes,it might just be a plugged hose,does the motor run hot?
@michaelwall1166
7 жыл бұрын
I just bought a 1977 johnson 35hp and put in a water pump kit when u have it in a barrel it spits water where you disconnect shifter shaft is water suppose be in there?
@jamesstier5673
9 жыл бұрын
I am familiar with the lake you are on. I have a 35HP Johnson that is getting real hot. Ran it last week and it seemed fine now last night it ran poorly and is over heating. I have a good stream from the tell tale but very little from the exhaust. Any recommendations on what to check?
@therealeeeo
11 жыл бұрын
I've got a '78 Johnson 35hp. The water doesn't stream out of that port under the motor housing, it just sort of drips. Most of the water seems to come out of the two exhaust ports on the back of the shaft housing. I assume this is normal, but it always struck me as odd that a lot of other motors usually had it squirting out in a solid stream while this one doesn't. Thoughts?
@chrysleroutboarddude
12 жыл бұрын
@thatguy360ful You might need to try a drfferent prop like a10 1/4x9
@sonofjabba
10 жыл бұрын
So you're telling me there is no difference in my 20HP 1988 evinrude and my 1985 30 except the carb but they list different part numbers for the internal engine components? My 30 has a reman power head but the lower unit needs seals and the transom tongue is a rusted wreck. You intrigued me.
@Dinkymaster7
10 жыл бұрын
Hi, are you a a boat engine collector? I love boat engines to, i had a 50s-60s Perkins 6hp outboard but unfortunately it got scrapped a few years ago :-( Was that a rare outboard?
@chrysleroutboarddude
10 жыл бұрын
Dinkymaster7 Yes i am a collector. I have heard of the Perkins but don't know anything about them.
@newyota1
7 жыл бұрын
I have a similar motor and running it on a lowe 1440 andt he tiller handle pulls alittle hard to the port at full throttle and on longer runs is alittle tiring to hold straight.Could you tell me if I can do anything to help it to steer easier?I thought about moving it left or right on the transom to see if that helps?Is this a possibility?thanks
@RustyShakleford1
7 жыл бұрын
newyota1 tighten up the steering tension bolt under the cowlin of the motor above the transom mount
@newyota1
7 жыл бұрын
Did that already.thanks.pretty tight and still pulls.
@davidthomas699
7 жыл бұрын
Do all S-14 require a long shaft? Or only the deep transom models?
@chrysleroutboarddude
7 жыл бұрын
They made them both ways.
@jasper60103
13 жыл бұрын
That'll put some wind in your hair. Nice runner.
@chrysleroutboarddude
11 жыл бұрын
Nope it is a 1989 Lund S-14'
@davidfarmer2049
7 жыл бұрын
Was the electric start standard? Where did that start in the hp range? I dont fancy hand cranking 35hp.....
@chrysleroutboarddude
12 жыл бұрын
@thatguy360ful I think so.
@stevrosssmearu5293
5 жыл бұрын
30 mph thats excellent thats about all my 93 70 hp force could do on a 16 bayliner maybe a bit more but not by much good video
@christiangrech1375
11 жыл бұрын
Hi, Is your boat 17 feet long ?
@fleetwin1
9 жыл бұрын
sweet!
@lucasignorello2850
9 жыл бұрын
hello I too have a 25 hp outboard jhonson you would like to do with switching on power button just like your I own a starter a rectifier and a relay would you be kind enough to help me do this ?
@chrysleroutboarddude
9 жыл бұрын
luca signorello Okay so what is the ?.
@lucasignorello2850
9 жыл бұрын
I do not know how to connect all
@postaltraining
12 жыл бұрын
you said "i just built" that motor. if you had to do pistons, rings, etc. can you PM me how much that might have cost you? i'm trying to make a decision on buying a short shaft 1977 35 with audible wrist pin slap and wondering what kind of parts bill i'm getting into if i do buy it
@buckkruszewski1059
4 жыл бұрын
Most people don't rebuild these motors because it's cost prohibitive to buying another good powerhead. I called about doing it once. The guy quoted me $75 a hole for boring and honing. I went the very next day and bought three of these engines as parts motors for $150. If you had one that was mint, maybe.
@chrysleroutboarddude
11 жыл бұрын
Well i can work on it! i am 30 miles from st paul.
@camisgtamas
9 жыл бұрын
Hi i jave a J6rc0b. Do you by any chance have a propeller for it
@chrysleroutboarddude
9 жыл бұрын
camis tamas Sorry i do not but hear is a new one. www.marineengine.com/newparts/part_details.php?pnum=OMC0778797
@chrysleroutboarddude
11 жыл бұрын
Ya that sounds like a plugged hose.
@mrpowdercoater
9 жыл бұрын
Do you run a gps? I would love to know the speed you're getting with these motors.
@chrysleroutboarddude
9 жыл бұрын
mrpowdercoater I have just started using one, and i get about 30/35 mph out of them
@mrpowdercoater
9 жыл бұрын
Great thank you. Are you going to start posting what speed your get in your all videos?
@chrysleroutboarddude
9 жыл бұрын
mrpowdercoater I am not planing too! For me it's more about how the motor runs not how fast it runs.
@sebhall938
9 жыл бұрын
Do you ever run old honda motors? It seems like you only run American motors...
@chrysleroutboarddude
9 жыл бұрын
Seb Hall I have run them! But i really only have 2 cycle motors.
Пікірлер: 61