This is exactly what I was looking for! I have been trying to figure out how those two inner doors are supposed to move. This video showed that perfectly thank you my friend!
@Geoff240ti
4 жыл бұрын
I was in your same shoes, took a ton of forum searching and head scratching. Ended up being fairly simple and easy to show so I'm glad the video helped!
@gimmefuel7268
Жыл бұрын
I can’t thank you enough for making this vid. Just wanted you to know that it has definitely helped an owner of an ‘84 to try & fix the same problem. Thank you sir. 🙏👍🏻👍🏻
@Geoff240ti
Жыл бұрын
Glad I could help!! Take care.
@paddykachur3585
2 жыл бұрын
Thanks. I'll have to make this bracket too
@tp5776
2 жыл бұрын
Common plastic break for age. I just drilled a small hole through the broke plastic piece and put the skinniest toggle screw I could find in it. The toggle pushes against the door when pushing out, the inset of the piece keeps it from falling through when pulling it in, and it works fine.
@WestCoastFront
3 жыл бұрын
I'm currently working on this project myself. Just replaced the AC clip that broke and broke another clip in the process. My concern is attaching new clip and cable to sync with the internal little flaps he mentioned. I noticed those works simultaneously.
@gavinb6004
5 жыл бұрын
I wish you could make a video on how to build this because I have the same problem and need a fix similar to this without rebuilding the whole system
@crownviclvr
5 жыл бұрын
Shouldn't be that hard just get a thin piece of metal angled like that and match it up to the plastic piece drill a few holes And Cut down to size
@johnclendinning1189
2 жыл бұрын
Those little clips are hard to find, but they are also used in other GM cars. I got mine from a Camaro
@brazenhammer3307
3 жыл бұрын
Thanks very helpful
@franklinwright7248
4 жыл бұрын
I have a 1978 Chevy Cheyenne does it have the same kind of build? I literally have no heat my truck still gets hot but I can't get any heat to it at all
@paddykachur3585
2 жыл бұрын
Probably same issue. Or vacuum line.
@mrblock1020
Жыл бұрын
I have a 86 and with everything off I get outside air coming through top vents and floor vents Would you happen to know what my problem is
@jesusochoa9423
4 жыл бұрын
so went I switch my vent to defrost the bottom vent drops but that side door stays open. how do i fix it where side door shuts when bottom vent door closes?
@MrJaespun
4 жыл бұрын
My 87 just heater core changed & now I’m getting constant air flow at feet, even when I change to defrost. You think it’s possible mechanic might have damaged this part you fabricated?
@Geoff240ti
4 жыл бұрын
Possible that part broke, also easy to install the vacuum lines wrong causing the wrong flaps to open/ shut
@MrJaespun
4 жыл бұрын
Geoff240ti thank you, I didn’t even think about the vacuum lines.
@MrJaespun
4 жыл бұрын
Geoff240ti I took mine apart & I confirmed that my plastic is also broken. How were you able to pull the nail that’s holds the plastic clip to the arm that pushes the doo open & closed?
@tomkelly3896
Жыл бұрын
I have an 87....ac comes out floor....no access to get into ductwork🤔🤔😎
@BryMed86
4 жыл бұрын
Can u tell me where you're getting your vavuum from???
@dumaineslade
4 жыл бұрын
looking from the front of the vehicle at the motor. you should have a small vacuum line coming into your engine area just to the right of the AC Evaporator. That line runs to a T. The other side of the T should be going to a round vacuum storage tank mounted in the far right corner on the firewall. The other connection of the T is the feed line pulling vacuum from the intake thru a small check valve. Pull your breather and just look for the check valve right behind the motor and follow the vacuum lines connected to it....
@BryMed86
4 жыл бұрын
@@dumaineslade thx man... none of mine is hooked up..will look today
@yomomsgamer
4 жыл бұрын
How do you get the old clip out?
@Geoff240ti
4 жыл бұрын
I had my box apart, but I'm pretty sure I was able to back the hex bolt out with it assembled. Is there a nut behind it? Can't recall.
@richardbartlett6701
Жыл бұрын
You can still buy that plastic piece. Under $10..
@Geoff240ti
Жыл бұрын
Thanks Richard, I was happy with the material upgrade, but good to know you can still get the actual part.
Пікірлер: 28