Rub it in buddy ! That one scoots that little boat nice !
@mistersnapon
4 жыл бұрын
That thing really scoots man!!
@deanferries7766
2 жыл бұрын
Thanks for posting been a subscriber for about 15years I think now and got a bit worried when I didn't see an new video good 5o hear from you again hope your well all the best from Australia
@oldjohnnyrude8404
4 жыл бұрын
That one turned out great! Not bad for a freebie.👍👍
@chuckcecconi4571
4 жыл бұрын
You two are the best small outboard mechanics I've ever seen, I thank you for everything. I learned enough watching you to start repairing them out of my garage.. Especially you Old JohnnyRude..
@oldjohnnyrude8404
4 жыл бұрын
@@chuckcecconi4571 Thank you, Sir! And thanks for watching! Mr. Dittmar has helped me out quite a few times too.
@josepheveland8300
4 жыл бұрын
Trying to get my 88 Gamefisher running like that on the river here. Can you give me some specs for the engine?
@tractorhyatt7044
4 жыл бұрын
Was it in working condition when you received it for free? If not, how much did it cost to get it running? Thanks! 🇺🇸🚜👍
@callious31
3 жыл бұрын
I have a 93' Gamefisher. Think I could get some assistance with it? Starts then shuts off soon as if it is starving for fuel. I cant find replacement carb for it.
@CraigArndt
4 жыл бұрын
Nice holeshot. Smooth runner.
@16casts
3 жыл бұрын
Hello, I have basically the same engine, runs really bogged down and doesn’t seem to want to hit full rpms, already did a seafoam flush, problem still exists. Seeing this engine run like this is unreal to me! Any advice or information you could give me would be so helpful, perhaps a video on how you worked with carb since this is what I believe my main issue is!
@fleetwin1
4 жыл бұрын
Sounds nice, plenty of power
@ko4nrbs
4 жыл бұрын
First of all we all owe you a great debt for posting your videos. Your time and expertise are greatly appreciated. I have a Sears (Westbend) motor that has a broken steering handle part number 183079-1. The motor is a 12hp Model 571.59271. Have tried Ebay, etc. and can't find one. Any idea who may have one? Thank you, Bill
@jackpinesavage9806
4 жыл бұрын
Excellent, always fun to watch your videos
@danielrobert7181
4 жыл бұрын
Sure has that Chrysler/Force/Mercury unique sound !
@nertski3238
4 жыл бұрын
Hi Ben, I love your videos. I just picked up a 1980 Johnson 15 hp. What ratio mix do you recommend? Everything I’ve read says 50:1 but I’ve heard you say 40:1 on an old Johnson video. Any help would be appreciated. Thank you
@urmomthemilf34
4 жыл бұрын
I run my 50:1
@seantilldawn
Жыл бұрын
@chrysleroutboarddude do you happen to have any video of of how much cooling water should be spitting out the back of one of these Gamefishers while at full throttle??
@timothysinischo6095
4 жыл бұрын
Sweet motor! I just bought a 1973 Chrysler 9.9 for 50 bucks that didn’t run and with the help of you’re vids it purrs like a kitten. I fixed the pull start, rebuilt the carb and fuel pump, and cleaned the points and bam 2nd pull! But I have this dark black stuff sleeping out one of the tiny holes in the lower unit. It’s not coming out of the drain / fill plugs. I did replace the lower unit oil before firing up. Do you know what that could be and is it serious?
@christophercipriani7074
4 жыл бұрын
These videos are great thanks for posting! Have you encountered any issues when adjusting for altitude? I recently rebuilt an '84 Chrysler 15 HP. I live in Colorado and the lake we typical fish is at 9,000'. Even with the idle mix as lean as it will go I can't maintain an idle, runs great WOT. Were there ever high altitude carb jets made for these motors?
@johnscheffler1514
2 жыл бұрын
Nice running motor. How do you tell years and who made them.
@childzplay5253
4 жыл бұрын
Please help! I have a 78 chrysler 6hp and the only impellers I can find are 150$, are there any that are similar that will do the trick?
@Mnoutboards
4 жыл бұрын
Yes use this one. You have to shorten the drive pin a little but it works perfect! www.marineengine.com/newparts/part_details.php?pnum=OMC0436137
@carlosadkins9221
4 жыл бұрын
Hey I just picked up a 1984 25hp chrysler looks great it is clean. But I think the carb needs cleaned. It has a little on and off sputter to it sometimes any ideas. Can I get a kit for it
@seantilldawn
4 жыл бұрын
Hello! I’m wonder if any one could recommend where I could could find a prop for my late 1980’s Gamefisher 15hp. It currently has an 8”x9 aluminum prop and it lugs pretty bad on my boat. I need less pitch. It’s a 10tooth spline. Any ideas??
@seantilldawn
4 жыл бұрын
Anyone out there with ideas on where to get a Gamefisher prop??
@edhein8299
4 жыл бұрын
That sounds good!
@thebard320
4 жыл бұрын
Good day Ben I live up in Edmonton Alberta Canada. I have watched your videos for a few years now. I have several older outboards from a 1956 5.5 Johnson to a 1965 20 hp Chrysler. I am not able to get parts for them. Could you please tell me where you get parts. I thank you for your time have a great day and keep up the good work.
@chrysleroutboarddude
4 жыл бұрын
The parts for the Johnson are available from Evinrude. Parts for the Chrysler are a little harder to find. I have some people that drive down from Edmonton to have me work on there motors.
@rockinonamerica1st722
4 жыл бұрын
@@chrysleroutboarddude Dude do you ever sell any of these smaller units? Am looking for a smaller outboard for my boat, maybe an older Sea King 9.6 or something close to that size?
@etintlable
2 жыл бұрын
Ben hope this finds you well. I have a 15hp Gamefisher Model 225 581 500 need a prop and shaft end cup. now a 2 blade which I will settle for but prefer a 3 blade P-715. Do you know where I can find one?
@tiberiud1955
3 жыл бұрын
Do you have a service manual . My friend from Romania it's looking for water pump for this engine 1997 model. He said it can only be found in USA. I will buy it for him and ship it to romania if I can get the correct part no. Please let me know.
@tjmone74
2 жыл бұрын
In need of help!! I have two questions. I have a 1989 Force 15hp. First question is, is the top cylinder considered cylinder one? And the second question is when I pull start I'll get three or four pulls then the next pull it will stop dead halfway through the pull. Any idea what causes that? Any help is appreciated.Thanks!
@jacobleon7306
4 жыл бұрын
Hey man love your videos,I recently bought a 1987 force 9.9 and it had a plastic propeller that snapped the first time I took it out,I was wondering if they made metal props for them or if they all have plastic props.
@FUzzyBUnnyBOoties
4 жыл бұрын
I have a couple old motors that could use your care. I wondered if maybe you would be interested in buying them?. I am up on Mille Lacs Lake. But would be willing to meet you. Whats the best way to get hold of you?
@cainscabana1080
4 жыл бұрын
Hey I just got a 1969 Chrysler outboard 9.9 it starts and runs for maybe 10 seconds and cuts off is there anyway you can help me I was thinking maybe clean the carburetor plugs are brand new
@laurencegiersch9615
2 жыл бұрын
I have 3 15hp montgomery ward/ chrysler VWB52122, all run excellent with very few hrs. Is there a company out there that make a propeller that would fit this but with a higher number pitch
@danielcantellano794
3 жыл бұрын
Do you know anything of a gamefisher 25 I’m trying get water pump impeller it want suck water?
@kevinmasters7189
4 жыл бұрын
Hello. Old Johnny rude mentioned you might be able to answer some questions. I just bought a 1980 Chrysler sea king 7.5. The guy said it ran but you know how that goes. Got it home and there's no spark on either plug wire. Bypassed the kill switch but still no spark. Started to try take off the fly wheel but stopped before i broke it since I don't have a puller and am a novice on outboards. Is there any common problems with these motors or things I should check. I did find a broken ground wire that looks like it goes up into the stator/magneto. Fixed it but still nothing.
@aNuthaRedneck
3 жыл бұрын
I've had similar problems on other motors. Often just replace condenser, clean and set points... probably set at .020
@maxhammontree3169
4 жыл бұрын
Hello Ben. Would you be able to tell me what kit I need to reseal a lower unit on a 1968 Chrysler 20 hp model 2023? Thanks
@zacroberts4437
3 жыл бұрын
Where can I get a carburetor for an 86 model
@michaelsolis2674
4 жыл бұрын
Where do you find all your carb parts. I can find the carb hollow needle that is like 2 or 3 inches long that's fits down the middle of the throat of the carburetor anywhere at all. Everywhere it is N/A no longer available I tried everywhere e en vintage and salvage I have a 1989 15 hp gamefisher
@chrysleroutboarddude
4 жыл бұрын
If you need that tube you are going to have to find a new carb. look on ebay.
@allangarcia9528
4 жыл бұрын
Hey man I have a 6 hp sea king and I wanted to ask about the mottor and how it runs and what it might be since u no about them it starts and trys to pretty much go out then gets going again and try going out again if ya can send me a comment back over this that would be awsome
@ThatGuySkimpy
3 жыл бұрын
I have the exact motor !!!!! Comes with a 10 Spline plastic prop. I cant find a replacement in plastic or aluminum. Anyone who where I can find one ?
@klikerklik8872
4 жыл бұрын
welcome to Belarus, I have a request to help me with the installation of uoz on the Johnson 6L boat engine since 1996. If it is possible to set it without a strobe light ??
@leonwilliams3212
4 жыл бұрын
I know this isn’t this video and I’m sorry but I just got my 6 hp Chrysler running I don’t know the year maybe 75? I don’t know where to buy a new impeller :/
@OutBoardTink62
4 жыл бұрын
The last of the Chryslers basically they used that design for years WestBend to Chrysler to Force and sold under the Sears Gamefisher tradename and to out of buisness ,LOLL.I have a few old West Bend made Elgins in my hoard thats a neat little motor sounds good ...Glenn P.
@thespiritof76.
4 жыл бұрын
You forgot about Eska...
@OutBoardTink62
4 жыл бұрын
@@thespiritof76. Yeah theres probably even more that they had with different trade names.....
@jorgeantonioricci7190
4 жыл бұрын
Very good 👍 is American? Jorge Antônio Ricci Brasil 👍
@johnbanninga5511
4 жыл бұрын
Hello Ben, I'm having major issues getting the recoil to work properly on my Chrysler 20hp. Would really appreciate any help!
Пікірлер: 62