I was thinking about trying the Matek -F405 for my first ever F/C board, Running INAV but thought it may be a challenge do to my lacking computer skills. I have watched the first two videos and so far as well you have laid out these videos I may give it a try. You have done such a great job explaining in detail
@jamesceastep8874
2 жыл бұрын
Lee: This is your usual outstanding videography, clear language, and logical order. I'm really looking forward to viewing all of your 7 modules for INAV 5.0! Jim
@Painless360
2 жыл бұрын
Thank you so much for your comment. You can watch the whole series now using the playlist.. Happy flying
@r7_guy941
2 жыл бұрын
You have got my attention now, I am looking forward to the upcoming vidieo's. Maybe a silly question, but can you explain when to choose INAV over Ardupilot ?
@Painless360
2 жыл бұрын
Covered in the first video in the series. INAV can be similar to setup if you know the configurator and you don't need the extra features that Ardupilot has, that usually require a lot more sensors (compass and airspeed) to work... Happy flying
@greatgandalf5233
2 жыл бұрын
Always great info or in USMC Aviation The Gouge... I will emulate your Mars build with INAV. Of course, needed over kill with a Matek F743 V3 flight control. SF A6E NFO or Man Moscow fears the Most.
@johnchurch2321
Жыл бұрын
Great video! Hey do you disable the trim switches in Inav or EdgeTx?
@Painless360
Жыл бұрын
If you do it, you'll need to do it on the radio. I have a video on that... best of luck
@Rippin-Rich
Жыл бұрын
Do you still recommend this flight controller, or would you pick a newer and better?
@Painless360
Жыл бұрын
Any of the current Matek Wing boards get my vote... Happy flying
@MCsCreations
2 жыл бұрын
Fantastic, Lee! Thanks a bunch for the video! 😃 Just one question about receivers. In case of using ELRS, Crossfire or Ghost, they use 4 wires instead of 3 like SBUS... So... Is there any 4 way connector that would fit like a servo connector? If so, what is its name? Anyway, stay safe there with your family! 🖖😊
@Painless360
2 жыл бұрын
Dupont connectors come in all shapes and sizes. I use the 4 pin ones for GPS here... Happy flying!
@MCsCreations
2 жыл бұрын
@@Painless360 Oh, fantastic! 😃 Thanks a lot, Lee! I already searched about it and found some options!
@robinkarlsson1460
2 жыл бұрын
Great stuff dude!
@jribeiro2009
2 жыл бұрын
Lee, thanks for this new series 👍 Considering that I already have INAV 4.1.0 on my CW Mini, can I paste the accelerometer values via CLI after upgrading to INAV 5.0? TIA
@Painless360
2 жыл бұрын
I've not tried but it's an easy one to try. Let me know if it works... Happy flying!
@jribeiro2009
2 жыл бұрын
@@Painless360 It worked perfectly :) Thanks!
@turboromy
Жыл бұрын
Extremely helpful !!! I've been flying drones with Betaflght and learning curve was very steep for me. Knowing it, iNav looks familiar. One question though, what kind of receiver are you connecting at 12:30 ? I was planning to use X8R. Is it possible to use R-XSR like on drones ? That'll be awesome. I was hoping to use more than 8 channels because whole purpose of it is to have FPV airplane.
@Painless360
Жыл бұрын
Anything you use already should be fine... best of luck
@axljackass
2 жыл бұрын
for me, one downside of Inav compare to Ardupilot is the trimming during maiden flight..i dont have full control during Manual flight mode in Inav, cannot do manual trim nor dont have Dual Rates, but in Ardupilot its more easier to do the maiden flight as you have full control over Passthrough mode..although we have autotrim mode in Inav but its not enough if you want to do initial trimming
@Painless360
2 жыл бұрын
INAV now does the same thing..keeo watching..
@joestubbs3138
9 ай бұрын
Lee - After Flashing I noticed DFU disappears and is replaced by the COM5 Port which opens up the Configurator on pressing Connect - COM5 being the key to open up the Configurator for your particular model - I get COM1 so my Configurator stays closed !!?? why is this - I've used Zadig & ImpulseRC Drivers - no Joy A week ago COM4 as did '' \\.\COM14 '' not sure what '' \\.\ '' means opened up the Configurator - is there a way to select a free COM Port to open up the Configurator - you can select a COM number at top of page but it is greyed out and invalid - been poking my fingers at various sites for a week now but no joy - I do hope you can shed even a festive candle light on my dilemma - have a very merry Christmas ...joe
@Painless360
9 ай бұрын
DFU should only appear when the FC is in BOOTLOADER MODE. So you shouldn't see that at any other time. COM Ports on each PC will be different but if you are saying that the port numbers have changed after an update, this isn't common. Maybe you replaced the normal driver too? Best of luck!
@robertday2391
Жыл бұрын
Hi Lee. LOS flyer, this is all new to me. Matek f405 wing no longer available, what FC would you recommend? Thanks.
@Painless360
Жыл бұрын
kzitem.info/news/bejne/uKOD2oGgjHNhmGU I'm using a WMN in the new INAV for beginners series starting soon... best of luck
@michaelwhinnery164
2 жыл бұрын
Ok my friend... I'm stumped. I have a tango 2 transmitter a brand new tbs crossfire nano reciever bound and in sbus mode my transmitter monitor shows everything working. Inav is on sbus all pre arming check Mark's are green, but when I waggle my sticks nothing moves on the monitor. I asked you about this before because my old reciever is soldered to a pwm adapter. This one isn't and I got nothing. I followed exactly what you did is there some setting somewhere I need to change ? I am really frustrated at this point. I know you aren't tech support but you are very knowledgeable about all of this stuff. And help would be appreciated.
@Painless360
2 жыл бұрын
Check out kzitem.info/news/bejne/wqdqzoahfXWmdqg about the 12:00 mark. Sounds like you have something incorrectly setup... best of luck
@P8FPV
2 жыл бұрын
I have a problem with my heewing and wing fc.. I hooked everything up on inav etc right servo to no4 output left to no3 output.. Now my roll is pitch and pitch is roll? I have moved roll and pitch in my tx seem to have worked for stick control but the fc is still the wrong way when moving the wing 😪
@Painless360
2 жыл бұрын
Don't change anything on the radio. See the other videos in the series...
@P8FPV
2 жыл бұрын
@@Painless360 I just did it was as simple as changing just one servo direction fgs thank you 😊
@DannyFPV04
Жыл бұрын
What receiver are you using in this video?
@Painless360
Жыл бұрын
The receiver is part of the DJI Air unit and sends SBUS to the FC..
@garthhansen6804
2 жыл бұрын
Hi Painless360 I am new to INAV and I am having difficulty loading INAV Configurator. It downloads fine, but I cannot get to the screen where you type version in. I did notice that when yours loads in the video it has manual at the top of the screen where mine has UDP. Also yours has a few images on the top of the screen where I have nothing. Can you help please?
@Painless360
2 жыл бұрын
UDP is used if you have a wireless connection to the flight controller. When plugged into your PC, a COM port should appear in the dropdown list. If not then check out the links on the INAV main screen to download the driver... best of luck
@garthhansen6804
2 жыл бұрын
@@Painless360 I keep getting "Failed to open MSP connection.
@Painless360
2 жыл бұрын
You need the right Com port selected in the drop down box. Try another USB cable as well. A more complete list of what you've tried already would be helpful...
@andrewjamez
2 жыл бұрын
I have bew matek board, came loaded with inav 4.1 It shows up with an asigned comport, The PC has connected and flased older versions on other boards so the stm drivers are all good. The new matek 411WTE ont flash at all. tried zadig although it shouldnt require it as it already is identified by windows and inav. Update usb driver with zadig anyway but now PC wont see the board at all. I had to roll back the usb driver so now Im back to square 1!. Always a ball ache with inav...any help appreciated. Thanks
@Painless360
2 жыл бұрын
I've not seen that. Connection errors are almost always driver or USB cable related... Best of luck
@andrewjamez
2 жыл бұрын
@@Painless360 sorted, I wasn't shorting the bootloader pads during zadig driver update.:)
@michaelwhinnery164
2 жыл бұрын
Hello my friend, I'm using TVs tango 2 transmitter and a nano reciever soldered to a 6 ch pwm adapter. I've thing I've done everything correctly, reciever is bound and connected to the transmitter calibration is done. But when I check for movement on the inav reciever page I got nothing. Any suggestions as to a different setup or ???
@Painless360
2 жыл бұрын
Why not wire the reciever directly to the flight controller via SBUS or CRSF?
@michaelwhinnery164
2 жыл бұрын
@@Painless360 I had it installed without a flight controller so it was previously soldered and now im installing a flight controller
@Painless360
2 жыл бұрын
You can still use CRSF or SBUS on those outputs... best of luck
@michaelwhinnery164
2 жыл бұрын
@@Painless360 yea I tried that and still got nothing. I noticed on the setup page under pre arming section everything is green except the (Navigation is safe ) that still has a red x
@paulsalminen9785
Жыл бұрын
Hi Guys I have an apprentice S15E with a matak F405 wing, running version 2.3.0 how can I save the current setting on the flight controller and update to the current version 5.1? I have a taranis X9D plus but dropped it so I need to buy a new radio to get the plane flying again. Any help would be greatly appreciated regards Paul.
@Painless360
Жыл бұрын
Upgrading from such and old version is tricky as so much has changed. See the upgrade path using things like DIFF ALL from the release notes on the INAV firmware. I'd make a note of things like the offset angle, modes, OSD layout and mixer settings and start again fresh with the latest version. Best of luck!
@paulsalminen9785
Жыл бұрын
Thanks Lee you do awesome content !
@DannyFPV04
Жыл бұрын
Can you install a speedybee wing into a plane?
@Painless360
Жыл бұрын
Yes, that is what they are designed for.. Best of luck!
@DannyFPV04
Жыл бұрын
Sorry I was asking if you could possibly do a future video with the speedybee as an install. Lol 😝 I really appreciate the replies
@Painless360
Жыл бұрын
That may be in the works ;) stay tuned!
@AnthonyGonzalez-lw1ek
Жыл бұрын
What is that RC plane ✈️ , please help from anyone who has that info thankyou
@Painless360
Жыл бұрын
A plane that is flown using remote control? en.wikipedia.org/wiki/Radio-controlled_aircraft
Пікірлер: 55