😂 😂 😂 I can’t tell you how many times my husband has said when something wasn’t going “right”... Just get a bigger hammer 🔨! 😂 😂 😂
@tractorrookie
4 жыл бұрын
Laura Wijkowski Smart man! Sometimes that’s all it takes. 👍😂
@kennygb123
2 жыл бұрын
Thanks for the video. Just finished installing a thumb on my CS 2520. Very helpful.
@tractorrookie
2 жыл бұрын
👍😊 Hi Kenny gb! Awesome! Thanks pal. I appreciate you checking out the video!!! Let the fun begin!!🚜🇺🇸🍺
@walterkucharski4790
4 жыл бұрын
I have the same hoe but installed the hydraulic thumb made for this machine from Michigan Iron. It's great! I love the convince of not having to set the arm manually. Good luck with yours.
@tractorrookie
4 жыл бұрын
Walter Kucharski Thanks Walter! I have enjoyed using it so far. I’m still learning!😁🇺🇸
@travishale1279
Жыл бұрын
Just picked up my Kioti thumb $400 with tax these days. Thanks for the video
@tractorrookie
Жыл бұрын
😊👊Hi Travis! Nice! I am sure you’ll love it, it definitely comes in handy on some projects! 🚜🇺🇸🍺
@TheStevedie
7 ай бұрын
I don't own a tractor, was looking at a kioti...once I justify the purchase. I was thinking about s thumb and how great it'd be, since I'd really be using it all for firewood. 400 is cheap...looks well built too
@fredrhodes540
3 жыл бұрын
Love your ratchet punch. Ha ha.
@tractorrookie
3 жыл бұрын
🤣😊 Thanks!! I appreciate you checking out the video! That was an early video, hopefully I have gotten a little better! Cheers!!🍺🚜🇺🇸
@BackDraftBikes
Жыл бұрын
The pin on mine seem to be a little too small where it passes through the bucket. It’s probably a quarter inch smaller than the factory one. Is that right?
@tractorrookie
Жыл бұрын
😳Hi Backdraft! Definitely should not be a quarter inch difference. That sounds like way too much play! Hopefully wherever you picked it up, can get you the right pins. Tractor supply also carries a good assortment of pins. Good luck ! You will enjoy use it , it’s a a lot of fun. Thanks for checking out the video, one of my first. 🇺🇸🚜🍺
@NGHTRYDR2002
Жыл бұрын
$330 ...! I WISH... The one for a Branson BH 90.. $1100! Outrageous!
@tractorrookie
Жыл бұрын
😳Wow! I’m sure you shopped around. I know when I was looking, there were a few folks that made them. Thanks for stopping by !🍺🚜🇺🇸
@4legdfishman
4 жыл бұрын
Thanks for the informative video. Subscribed! I just got my Kioti CK2610 with the KB2475L backhoe. Definitely need the thumb. For $330? Is that correct? Sounds too good to be true. LOL
@tractorrookie
4 жыл бұрын
Carl Harrington Thanks! I’m glad you are along for the ride! Yes, ordered my thumb from the Kioti dealer. They had me wait till their next shipment from the company so I didn’t get stuck for shipping charges. I use that thumb pretty regularly. Take care!
@tonykimbrell3254
3 жыл бұрын
I am pretty sure that is the same backhoe as the bobcat BH76 I have on my bobcat ct 2025 ,I have been looking at pics and I believe Michigan equipment makes them but for a higher price these days which may lead me to just paying a little more for a bobcat one .
@tractorrookie
3 жыл бұрын
😊👍 Interesting! I have seen a few aftermarket units. I’m with you on getting it from the brand you buy. I think the plug and play is a sure fit and I think the resale value would be better. Thanks for checking out the video!🚜🇺🇸🍺
@mikeq5664
2 жыл бұрын
Hello, I just bought my first tractor and the same unit... a Kioti CK1035 SE.. (after a year of research) being enjoying your vids... just bought the thumb kit trough my dealer but chose to install it myself.. but nobody had a vid on the install... mine did have instructions though... 🙂I have to say it was straightforward but,,, with the paint on the parts and everything being new I cannot for the life of me change or adjust it...it's sooooo stiff to move it. Did you experience this? have to use the hydraulics on the bucket to help move it and line up the holes. Thanks.. and keep up the good work, you have a beautiful property !
@tractorrookie
2 жыл бұрын
😊👍 Hi Mike! Awesome! Congratulations on your new tractor! The backhoe thumb is great and a very fun little tool to have. The tolerances on mine were not tight at all, it is very easy to adjust. I’m not sure what would help, maybe a little grinding?😎💪 I appreciate you checking out the videos and leaving feedback. If you have any issues or questions, don’t hesitate to reach out. Good luck with your new ride! Be safe!🍺🚜🇺🇸
@mikeq5664
2 жыл бұрын
@@tractorrookie now knowing you did not have the same Issue, I think I'm going to pull it apart again and wire wheel off the paint in the inside where the shaft and big pin goes through, I will just keep it well oiled to help prevent from rusting...... Thanks for the impute 👍
@tractorrookie
2 жыл бұрын
Makes sense! 👍
@donnanewton782
5 жыл бұрын
Your wife has taught very well in how to podcast. Just kidding. You have a lot of knowledge
@tractorrookie
5 жыл бұрын
Donna Newton she has taught me a lot. Good and bad 😎😂
@btaylot431yt
4 жыл бұрын
Looks like something I could use!
@tractorrookie
4 жыл бұрын
BRUCE TAYLOR definitely very handy! Thanks for watching!
@albertwestphal4344
3 жыл бұрын
I HAVE FOUND OUT BY PSDT EXPERIENCE TO USE TAPPERED BOLTS WITH THE HEAD CUT OFF FOR GUIDING THE NEW PINS OR BOLTS IN.
@tractorrookie
3 жыл бұрын
Hi Albert!! Now you tell me!!! 😂👍 Thanks for the feedback! I appreciate you checking out the video!🚜🇺🇸🍺🔨
@donaldstrishock3923
3 жыл бұрын
My kubogy equalivelent for a bigger bh92 from the dealer (kubogy brand) was at a low-low price of 946.oo$ ---what a rip! It is VERY strongly built, wish it was hydraulicly actuated;; they just want a measly 1995.oo$ to rig it up right!! I by-passed the 2000$ idea and just jump on&off the tractor 40-50 times a day to "dial" it in properly--- what a pain. Going to "rig" some hydralics up someday soon to end my suffering and use it much more effectualy. Kubogy doesen't make it easy to do it aftermarket though---different pins, odd-ball legths,& goffey positioning. They want you to "pay" if you want to play. So go "hydraulic" sone as possible & don't be a "hard-head, cheep-skate" like me. I have used other machines, with the "hydraulic thumb" and the difference is like night&day!!! Just go for it and thanks for vidio Man.
@tractorrookie
3 жыл бұрын
💪👍 I hear you!!! Baby steps!!!😊😜 Thanks for checking out the video!!!🇺🇸🍺
@camerontitus5822
3 жыл бұрын
I realize Im pretty randomly asking but does anybody know a good site to watch newly released movies online?
@conradkeith9093
3 жыл бұрын
@Cameron Titus flixportal =)
@camerontitus5822
3 жыл бұрын
@Conrad Keith thanks, I signed up and it seems to work =) Appreciate it !!
@conradkeith9093
3 жыл бұрын
@Cameron Titus You are welcome :D
@jessefields9535
4 жыл бұрын
Where did you purchase it?
@tractorrookie
4 жыл бұрын
Jesse Fields 🌟😎I bought mine at Cowlitz Rigging www.loggingsupply.com/ They are our local Kioti dealer. I paid $333. They added it to their next shipment so I didn’t have to pay shipping.Hope that helps. Thanks for watching! 🚜💪🇺🇸🍺
@jimsadler2342
3 жыл бұрын
1/2 in metal is not stout enough I installed one that I bought from Titan first log that I gripped it snapped in half. The claws need to be thicker metal
@tractorrookie
3 жыл бұрын
🌟👍 Interesting! I have been using the thumb over the passed year with no issues. Maybe I baby it too much. Titan makes some pretty decent stuff, but shit happens I guess. I’ve been happy with the factory thumb so far. Thanks for watching!🚜😎🇺🇸🍺
@jimsadler2342
3 жыл бұрын
@@tractorrookie I do believe that it was a bad piece of metal. The man that I spoke to at Titan didn’t seem to care so I will build my next one using 3/4 metal
@tractorrookie
3 жыл бұрын
That’s awesome that you have the skills to get it done. Not too happy to hear about Titan! 🙁
@jakeyoungker
3 жыл бұрын
There are 2 different companies that use the titan name. Titan attachments and Titan Implements. One is a good manufacturer and one is all Chinese products imported and sold for cheap online that never last.
@jimsadler2342
3 жыл бұрын
@@jakeyoungker the company out of Tennesee is where I bought my thumb. I got some 3/4 inch steel to make the claw out of and it works get.
Пікірлер: 44