That was a cool video! Finally a build video I can enjoy. Loved seeing the custom machine work done on the lathe and the time to indicate it all. Great content
@TurboAdam
Жыл бұрын
Glad to see all the new content man! Been following for years. You inspired MY turbo LS Crown Vic build! Your dominator tune got mine up and running actually. Thank you for everything you do!
@cameron878
Жыл бұрын
:blushes: thanks for the kind words!
@mountainsgarage
Жыл бұрын
Great video, fun to watch a skilled builder do his thing!
@mtedwards78
Жыл бұрын
This is intensely satisfying. Makes me want to build another.
@davidmull1540
Жыл бұрын
thank you for taking time to do this!
@richardsmith-qy6vl
7 ай бұрын
I sent my fairbanks turbo 400 to a friend to rebuild and when he tore it down the case was no good they have those raised parts in it i dont know if it where the drume sits but he told me it happens alot from down shifting it so much so he was looking for a case for mè and i was also looking for one i called a friend he saidhe had one that was in a blower car he bought but it was converted to a 2 speed he gave it to me he said it was pulled out the car because 1st gear was t0 aggressive for driving it on the street so i guess thats why it also dont have a transbrake or a manual valve body . I never used it yet my buddy found me a good case and built a 400 for mè with s manual valve body with a reverse pattern im sorry now i never had him sèt it up with a trans brake once i get my 421 built im going to put it behind that and see if i like it. Great video
@philbetthauser9547
Жыл бұрын
That's one heck of a unit you built.
@robwigglezz944
Жыл бұрын
Very cool. Thanks for taking the time to do this. We all know time is money
@BigMikesGarage
7 ай бұрын
Nice work. Love the attention to detail.
@hankclingingsmith8707
Жыл бұрын
FINALLY SOMEONE WHO KNOW WHAT TO DO TO BUILD A PROPER HIGH HORSPOWER TURBO 400. THX
@garywoods148
Жыл бұрын
Nice video! Looks like you learned a lot from Hutch and the other guys on Yellow Bullet. I just did a pro mod direct drum and wound up with .125 clearance. Had to get the manufacture to send me some extra steels. They were .060 wish I had a lathe to cut some factory thick steels to take up the clearance.
@cameron878
Жыл бұрын
Wouldn't be where I'm at without those guys in the transmission section!
@ls87gbody
7 ай бұрын
Love the video . I wish you did more th400 and powerglide videos in depth like this. Please do a 3 speed th400 or powerglide, 1200-1500hp buildup. Subbed and following.
@TurbineResearch
Жыл бұрын
Awesome videos !
@cameron878
Жыл бұрын
Thanks!
@SquirrelTuned
Жыл бұрын
I am not a fan of working on transmissions. But watching this is like a speed run of it and makes the process much more enjoyable lol.
@cameron878
Жыл бұрын
That's what I was shooting for, leave all the fluff on the cutting room floor and just put the meat and potato's in, thanks for the kind words!
@SquirrelTuned
Жыл бұрын
@@cameron878 Nailed it for sure. I would be happy if I didn't have to take one apart ever again and I enjoyed all the way through.
@BigFun4Life
Жыл бұрын
Great informative video,thanks for sharing your knowledge..
@SloppyMechanics
Жыл бұрын
yueessssssssssssssss
@Gearbhall
Жыл бұрын
I was wondering why this came up in my feed, and I am glad it did.
@davidreed6070
Жыл бұрын
That was very interesting and informative. Thank you.
@dresdensvo
Жыл бұрын
Great video , I will use it many times . Now if I can find a 4L80 video this good .
@Qwiktripz1320
Жыл бұрын
Good video man. I just built almost the exact same unit down to the Farrer Valvebody. Only difference was using a intermediate clutch eliminator.
@rajcam80
Жыл бұрын
Nice work! I am prototype builder for a OE manufacturer. The new stuff is similar to the past.
@cameron878
Жыл бұрын
What's next up after 10 speeds?!
@rajcam80
Жыл бұрын
@@cameron878 I believe eclectic or hybrid. Not sure there can be a higher speed transmission.
@Gearbhall
Жыл бұрын
This was a very interesting look at the work that goes into this. Also... am I recognizing your name from the sloppy mechanics community? edit: I see Matt's comment now so that answers that.
@Ribbityibzki
Жыл бұрын
You spending 8 hours on a TH400 makes me feel like a hack slapping RFE's back together for dealer warranty.
@cameron878
Жыл бұрын
I don't build a bunch of race th400s, mostly daily driver stuff around here. Finding bad parts in 40 year old transmissions, walking all over to get core parts, machine work, plugs here, restricting feed holes there. Phew. I can completely tear down, bushings, seals, etc, and build, including all the pump and VB updates a 4L60e in 3-4 hours if no one bothered me and the phone didn't ring. A th400 with a bunch of aftermarket stuff? They always take me a while.
@chambjm
Жыл бұрын
11:50 makes me want sweet and sour chicken
@cameron878
Жыл бұрын
Gen tso > seeet and sour
@alchampion340
9 ай бұрын
GREAT Video. Will you sell a couple lower gear sets?
@billbaggins9961
Жыл бұрын
this is exactly why I would pay for this service. I was lost after the first snap ring!
@promobass77
4 ай бұрын
very cool!
@troybaum114
Жыл бұрын
hell yeah bro
@emccolly
Жыл бұрын
Yes!
@GodModeBitches1970
11 ай бұрын
You make it look easy. Is there any material or guides you'd recommend? I want to build a th400 for my chevelle over the winter. Thanks for the video.
@cameron878
11 ай бұрын
Get a 3L80 ATSG manual, check out the transmission section on yellowbullet.com, I have a long thread over there from like 10 years ago that has some good info
@waynew2831
8 ай бұрын
Can you tell me about the vacuum line going to the modulator valve? Does the hard metal line have a check valve in it ? Can I run a line from the modulator valve to the manifold vacuum on carb?
@mikeg4163
Жыл бұрын
Cool video
@tomperry9954
2 ай бұрын
I enjoyed the video. I do have a question. With the Ultra bell, how do you insure that the centerline of the crankshaft and input shaft are in alignment? I seem to remember offset dowel pins back in the day.
@cameron878
2 ай бұрын
The 8 pump bolts are shouldered and I believe that's all that aligns it. I'm sure there's a way to check it, I never have and have never had an associated problem. That doesn't mean I'm right though. Lol
@cameron878
2 ай бұрын
Also, thank you for watching and the positive comment
@bigfoot355
Жыл бұрын
This is great!
@danielharmes8799
10 ай бұрын
Can you tell me do all converters fit early and late 4l80e's looks like there is a differance in hub height. I have a hughes 25 25L which has a 2" hub hieght and there telling me it won't work in a late 4l80e any ideas. Cheers
@pedricktownperformance6781
Жыл бұрын
I also use the 4l80e intermediate piston and 4 clutch stack in the th400. What's your opinion on Teflon rings on the pump and center support? I've used teflon and metal rings but never had any issues with either one. It's nice to see someone else spin and move your drum pistons up and down to make sure the seals are in right, other then the intermediate obviously.
@cameron878
Жыл бұрын
I use metal with stock rebuilds, not in fixed line pressure, other professions told me it won't end well. I've used both of the 4L80e style sealing rings and the orange scarf cut Teflon all with positive results
@BEANS-O-MATICtransmissions
Жыл бұрын
A 4l80 int piston sits below the snap ring in a 400, it has a gap to close before even hitting a steel. May be better off milling a 400 piston to get clearance.
@pedricktownperformance6781
Жыл бұрын
@BEANS-O-MATIC Transmissions the early 4l80e piston fits with no issues, the late 4l80e piston you have to use the small wave plate to make up the height difference in the piston.
@timweb1510
Жыл бұрын
Can you build a 3 speed next
@cameron878
Жыл бұрын
It basically looks the same except with a different valve body
@timweb1510
Жыл бұрын
@@cameron878 I’m trying to learn my best about this turbo 400 I have and what parts need to be modded trying to reach 700-750 wheel.
@flinch622
9 ай бұрын
The pan at 31:16 ... I don't recall seeing a stamped/stock cover with drain in that location. Modified? I could use one of those...
@cameron878
9 ай бұрын
Came on HMMWV cores
@jdubcbr600
Жыл бұрын
I would've thought the billet forward hub would've came machined for a bearing. Shows what I know...
@averykruger7957
Жыл бұрын
I hope the converter wasn't sitting around for too long 😅 What is the mystery spray in the Zep bottle? Or the super goop you put on the intermediate piston seals?
@cameron878
Жыл бұрын
Wd-40 to keep it from rusting. 50/50 mix of ATF and STP oil treatment
@BEANS-O-MATICtransmissions
Жыл бұрын
@Cameron Vic i use the same mixture, love it for assembly! Made me smile to see that.
@BlaserBuilds
Жыл бұрын
Made it to the end. What lube are you using in the cat sprayer?
@cameron878
Жыл бұрын
Little wd40 to keep it from rusting inside while my friend finishes his truck it's going in
@BlaserBuilds
Жыл бұрын
@@cameron878 Ahh, nice.
@hiddenman99
Жыл бұрын
Are you the converter guy Cameron? Forgive my ignorance, great video!!!
@cameron878
Жыл бұрын
I'm not sure what you're asking? I think you're asking if I'm the guy from cameron's torque converters. I'm not, he's over in South Carolina I believe. I'm in TN, I'm a nobody compared to him.
@hiddenman99
Жыл бұрын
@@cameron878 yes That is what I meant to type, and good work to the Video and the build.
@nyxie_games8904
9 ай бұрын
your video is awesome. do you have a valve body and plate combo for Low& Reverse only. its for a demo derby build
@cameron878
9 ай бұрын
I'd bet my buddy Grady that built this valve body could build you one like that
@cameron878
9 ай бұрын
Search "farrer out transmissions" on Facebook, message that page, they might be able to help you
@tracyscott70
Жыл бұрын
I wood love get my th400 built to 2-speed
@Adrianzx
Жыл бұрын
I cover up my ways whenever using abrasives
@ddmorphballzz2651
4 ай бұрын
What did u add to the tranny fluid to make it thicker. Brushed on nice. I'm about to start a th400 build and want to mix some up
@cameron878
4 ай бұрын
STP oil treatment
@stevedeschamps8758
5 ай бұрын
Would be nice to hear all details
@cameron878
5 ай бұрын
It's basically all in the video
@hartiaacres
6 ай бұрын
whats the ball park cost for the parts used for this build??
@cameron878
6 ай бұрын
3k-35 just for parts
@funfun8095
Жыл бұрын
Why do you use steel sealing rings instead of teflon? I never use the steel ones.
@mtedwards78
Жыл бұрын
I'm pretty sure those are 4L80e "PEEK" teflon rings. They are dark and can look like iron, but they don't interlock like the stock th400 cast iron rings do.
@funfun8095
Жыл бұрын
@@mtedwards78 Those are interlocking the same as stock.
@cameron878
Жыл бұрын
Mike is right, they're from an 80e. They are not steel.
@funfun8095
Жыл бұрын
@@cameron878 Have never heard of them. I use the solid Teflon or scarf cut Teflon.
@cameron878
Жыл бұрын
@@funfun8095 I save one from every 4L80e performance build (the one you leave off for dual feeding) and I use them on 400s if I have 5 saved up.
@mikeschreifer5819
10 ай бұрын
I want one how much?
@BoostedCyclePerformance
Жыл бұрын
I’m surprised no one has lost their mind about the lathe cutting in reverse.
@cameron878
Жыл бұрын
When was it cutting in reverse? Or do you mean the feed?
@jsmcortina
Жыл бұрын
Increasing the i/d of the steels.
@BoostedCyclePerformance
Жыл бұрын
@@cameron878 I meant the feed.
@CogswellRacing
Жыл бұрын
What do you charge for a 2 speed like this
@cameron878
Жыл бұрын
This is for a buddy, we mostly do stock rebuilds, and the occasional hot rod unit for a local racer. We don't have a dyno so we don't like shipping out units, too much risk. Grady farrer (the guy who designed the brake I used) might be your guy
@mikefoley7561
Жыл бұрын
Was looking into buying some parts from them but no parts page anywhere. What gives
@cameron878
Жыл бұрын
Www.coanracing.com
@accuratetowing8607
7 ай бұрын
Price To Build ?
@cameron878
7 ай бұрын
This was a build for a good friend, I've never priced one out for a retail job, he had some of these parts already so that offset the cost greatly. This is probably a $4500-$5000 build if I were to do one in the future though.
@bretteinhorn8507
Жыл бұрын
Chevy powerglide lol
@cameron878
Жыл бұрын
Kinda, this is a little stronger for less money
@bretteinhorn8507
Жыл бұрын
@Cameron Vic are you Denmah Cameron?
@prostreethustler239
Жыл бұрын
and The cost of that build
@cameron878
Жыл бұрын
Free for my good friend that does a lot of fab work for me for less money than he should.
@prostreethustler239
Жыл бұрын
@@cameron878 Nice now thats a buddy so what would it cost to build that trans ?
@cameron878
Жыл бұрын
@@prostreethustler239 it has a lot of nice parts and time. Bellhousing, super drum, billet input and main, billet hub, two speed, and dump. Probably in the $5000 range if I were to do another one for someone local.
@tommywilliams5135
Жыл бұрын
That's good price on that trans
@onetransmission7871
8 ай бұрын
Just so you know you cheated a little on your video. Few mistakes in there also.😊
@keysautorepair6038
Жыл бұрын
Many mistakes are made building this transmission.
@cameron878
Жыл бұрын
I don't doubt that! Lol. Do you have any suggestions?
@keltecfan
Ай бұрын
Or perhaps you have taken the time to video yourself building a similar TH400 and can show us all the correct way? Link please?
Пікірлер: 110