Thanks for the detailed video. I'm a 31 year old woman and I had no problem replacing these parts. You saved me over $400.00.
@ben156
5 жыл бұрын
Just because you're a woman and 31 years old doesn't make you more or less capable of anything in this world.
@rickeyponder
4 жыл бұрын
I cant get the screw in the back
@philwilson4476
8 жыл бұрын
Mr. Guptill, I cannot thank you enough for your video. My blower motor went out this morning, and thanks to you, I can track down and replace the failed parts. Your video is very informative, detailed and you clearly stated the important information that one should know, to tackle this job. This is my Saturday morning job tomorrow, and I can address it with complete confidence. Thanks again!!
@megaloogy
8 жыл бұрын
Thanks Phil. Hope it goes well for you.
@philwilson4476
8 жыл бұрын
Don, Thanks to your detailed instructions, the job was a success. I did have to replace the motor, and it's a challenge for a large man, but can be done. I'm estimating I saved myself around $150 labor, thanks to your video! Thanks!!
@jodybyram7045
4 жыл бұрын
The fan in my wife's car started dying in the middle of a heat wave, and this video was just what I needed to avoid a divorce! :-) Thanks for the tips!
@megaloogy
4 жыл бұрын
LOL. Thanks for the comment. Never dreamed I'd save a marriage with the video!
@francisdarsillo7481
9 жыл бұрын
Don - just replaced the blower motor on my 2001 Caravan. The vehicle was frying blower motor resistors every time I put one in and I figured the old blower motor was just drawing too much current (also the two prong connection where the motor wires connect to the resistor block was melted). The old motor was difficult to turn once removed; the replacement was more or less free-running. Anyway, a successful project thanks to your excellent video! However, I hope this is a once in a lifetime experience. The van just passed the smoke test - here's hoping it lasts.....
@megaloogy
9 жыл бұрын
Francis Darsillo Glad my video was helpful to you. Sounds like you found the culprit.
@BigDizzad
6 жыл бұрын
Watching your video saved me a lot of trial and error AND over $350! Bless you and Thank You Sir.
@megaloogy
6 жыл бұрын
Thanks BigDizzad. Like your International Harvester logo. I have a1855 IH cub lo boy to mow my lawn. Great tractor!
@scottspeer4003
6 жыл бұрын
This is by far the best video I have ever used on You Tube, it was very detailed, easy to understand and short and to the point....Thanks Don!
@megaloogy
6 жыл бұрын
Thanks Scott. I'm glad you found it helpful.
@cll1out
5 жыл бұрын
This is better than finding out that I would have to remove the dashboard like i expected. Our fan hit that dead spot last fall, we had an engine failure and I rebuilt the engine over a couple months time. After all that and getting van running again the blower was running again too. I believe the fan vibrated out of the dead spot with all the action in engine removal/install. I am certain it will fail again (land in the dead spot) and plan on replacing it before that happens. Thank you for the informative video
@megaloogy
5 жыл бұрын
Thanks for the comment. Some have said they restarted the motor by banging on the blower housing which still indicates a dead spot so if it fails before you can replace it, that may get you going again for a little while. Good luck and in case you haven't read some of the comments... some have just twisted and broke out the housing rather than trying to remove the 5th screw. The four screws that are left are more than adequate to hold the housing in place after installing the fan motor. Good luck!
@jtaylor2605
9 жыл бұрын
Don,This was helpful to watch and much appreciated. However, I did want to share with the group that the resister pack actually resists the ground circuit to the motor, not the power/voltage. The motor has power on with ignition (far right top green wire out to motor). By selecting a different setting on the fan switch will allow more or less resistance to ground and will make the fan run at slow to fast speed. To test this, just jump a chassis ground wire to the bottom far right black wire. If the motor/fan blows, it is still good. I have just tested mine and it is just the resistor pack.Thanks again, just wanting to offer some advice that may save someone money that may still have a good motor/fan.Good luck all, John
@thestiletto5584
7 жыл бұрын
Don, thanks for this video, saved me a ton of money and effort in replacing my blown resistor. +J Taylor, I owe you a beer! My initial diagnosis was that my blower motor was toast. But after reading your suggestion about grounding the black wire of the blower motor to chassis, I tried it and it worked. Thus, I only needed a $15 resistor and not a $72 blower motor. At least for now! Thanks JTaylor!
@kohokoho3065
6 жыл бұрын
READ J TAYLOR COMMENT BEFORE PULLING FAN OUT. I wish I would have read your comment earlier. I tore apart the whole fan assembly and hooked up the fan to a battery and it worked. So I hooked it back up to the resistor and it didn't. I tried a power wire from the resistor (green wire) but grounded it instead to the frame and it worked fine, so that is how I figured out the role of the resistor in grounding. So if that had been explained in this video in the first place, I could have saved myself over an hour disassembling the fan unit and ripping out insulation. Now I have to try to put it all back together. Makes me wonder if after he replaced the fan in the video, if it wasn't actually a dead spot in the motor, but it was also the resistor and he had to replace that too.
@fire7765
6 жыл бұрын
great information
@jasjar72
7 жыл бұрын
Bought the fan motor for around $70 - took a couple of hours to replace. "That one screw" was a doozie. All is well again! Thanks Don.
@megaloogy
7 жыл бұрын
Thanks for the comment Jason. Glad to help.
@fxm5715
5 жыл бұрын
Thanks, Donny. I just did this job on my 2005 Grand Caravan today. Because of your video, I was prepared with the tools I needed and the correct level of expected pain-in-the-ass effort. Whoever thought it was OK to burry that screw way back there, imbedded in an inch of fibrous insulation, should not be designing cars! Thanks for saving me a few hundred bucks and helping me keep cool this summer!
@megaloogy
5 жыл бұрын
Thanks FXM. I'm glad my video was helpful to you.
@glennnile7918
11 ай бұрын
Thank your mechanic friend for the explanation of the motor failure. That is exactly my problem.
@andrewdeacon6785
8 жыл бұрын
Went last year Florida to Ontario then to New Hampshire then back to Florida. My 2001 Grand Caravan made it to the top of Mt Washington, but before that I had the same problem with only high and low fan speeds. Once I got home and found this video, I was able to put in a new resistor easy as pie!This year the same trip, and ended up having the same problems, only the fan controls also stopped working altogether the last day of our return trip. 95+ at stop lights in Florida - Ugh! So I changed the resistor again but still nothing. So I bought a new blower and again this video helped me out tremendously. I even got that pesky #5 screw out without removing the sound deadening! Right now it's raining buckets, but it'll be all sunny in a few minutes, and I'll finish putting it all back together. I did test the new blower OOTB on the resistor, before diving too deep into the teardown, and it runs on all speeds. Thanks loads Don - you helped me twice now!
@megaloogy
8 жыл бұрын
Thanks for the comment Andrew. I'm glad I was able to help. That old blower motor was going on you last year most likely. You should be all set now.
@georgeperez2592
8 жыл бұрын
This video helped me fix my ac yesterday, which was hardly blowing. I live in Houston and we are battling 100 degree weather. On behalf of my family, thank you sir.
@megaloogy
8 жыл бұрын
I'm in Vermont and it's 95 today. Just a taste of what you have. Glad I was able to help.
@TitaniumGamerGM
5 жыл бұрын
Thanks for the great video. Following your instructions I was able to replace the blower in my 2004 Dodge Grand Caravan and save a ton of money. I wouldn't have had a clue without watching your video. Regarding your disclaimer, my Caravan has an automatic climate control and your procedure was exactly the same.
@megaloogy
5 жыл бұрын
Thanks George. I'm glad my vid was helpful. Wasn't sure about automatic climate control. Good info for future viewers!
@fleetofwjs1893
Жыл бұрын
Thanks Donny. Watched this last night, replaced the blower motor in a 2007 today. Whoever thought up that 5th screw in the back deserves a punch in the mouth. 😀
@FergusonTO30
8 жыл бұрын
Don, Replaced my blower and resistor today in about three hrs. Many thanks to you, as your video saved me many hrs. Not only did I know about the $#** 5th screw, I had all the tools I needed on hand. Went from no blower operation at all, to 4 functioning speeds. Again, many thanks!
@megaloogy
8 жыл бұрын
Thanks Todd. I am very gratified to have helped so many with this problem. Always enjoy the feedback.
@andreass.9398
5 жыл бұрын
Thanks Don for your step by step instructions and for including details like disconnecting the negative wire and making sure the fresh air door was in the right position when replacing motor. I saved myself having to pay an hour of the mechanic's time and gained the satisfaction of doing it myself. Thanks for your help.
@megaloogy
5 жыл бұрын
Thanks for the comment Andreas. I'm glad you found it helpful.
@kentcarlin3723
8 жыл бұрын
We had our blower fan quit last summer, just in time for those 103 degree days in California. Therefore, no AC in front. The resistor happened to be the culprit, thank goodness, but now, the wife complains that the front blower motor makes noise and smells like burning wire. While I didn't enjoy your talk about that last screw "being a bear", I think you hit the nail on the head. Thanks for a good description of the process.
@megaloogy
8 жыл бұрын
+Kent Carlin Thanks Kent. I take it the motor had to be replaced. I think sometimes when a motor is dying it pulls more amps to run and kills the resistor. Could be your motor was on it's way out.
@Iciielitez
8 жыл бұрын
+Don Guptill I have a bad blower motor, I've replaced the resistor twice and each time I put the new resistor in with the bad motor it smells burnt. So just get yourself a new blower motor.
@JonathanFont
2 жыл бұрын
This was great, I am here in 2021 learning about my van that is older then all my kids and 5000 miles from 200,000
@Razorusskie
7 жыл бұрын
I'm no mechanic, but thanks to your video I was able to change the blower motor in my 2006 Town and Country. we live in Tampa and use the AC year round. My wife and I BOTH thank you!
@megaloogy
7 жыл бұрын
Thanks for the feedback, I'm glad I could help.
@pridmore6
7 жыл бұрын
Thanks for doing the video. The most important thing you mentioned was when you bench tested the motor it worked. I did the same and put it back together. I wasn't sure what was wrong. After seeing your video you pointed out something important, the motor has a dead spot. Thanks. I haven't fixed it yet, but you answered an important question. Thanks.
@megaloogy
7 жыл бұрын
Thanks Teresa. If it stops working on you again, you can some times get it started again by striking the fan housing a few times. It may move the fan position a little bit and get the motor back to a good spot. Thanks for the comment.
@clinthanks3841
9 жыл бұрын
Don, glad you posted this excellent video when you did because there is nothing else out there nearly this comprehensive. We just R&R'd the fan and thanks to your video, we were ready for the unexpected and got through it in about 1 1/2 hrs!
@megaloogy
9 жыл бұрын
Thanks for the feed back Clint. My motivation to do the video was the frustration I had with R&R on utube for good info. I hoped to help others with this common problem.
@taggline
9 жыл бұрын
Very well explained instructional video. Thanks for this. I will now (attempt to) replace the blower motor on my '05 Town & Country mini van. Hold on for dear life, kids...daddy's gonna try and 'fix the car'!!
@Dominic-jb1uf
6 жыл бұрын
Don, can't thank you enough for the detailed video of doing this job. That 5th screw is in the worst spot. I'm 5'8" tall and average weight and I could not get a visual on it with my best effort. I had to do it all by feel and using a 1/4" drive with about a 3" extension mounted to a 5/16" socket. Needless to say, I did not replace that screw in case I ever had to get back in there again. Once I got the old fan out the job is pretty straight forward. Thank you again. Keep working safe and thanks for having the patience to do the job AND take video of the whole thing. Very helpful.
@megaloogy
6 жыл бұрын
Thanks Dominic. Glad to help..
@stevepage7717
6 жыл бұрын
I watched a few of these and yours was by far the most helpful. Just the right amount of information and you went slow enough for me to follow unlike some other videos on KZitem where they move/talk to fast. My only recommendation would be to not hesitate to break off that back bolt if you’re having trouble. I couldn’t get it so I made sure to get a clean break and snap it. 4 8mm screws hold the housing on just fine. Thanks for the video!!
@megaloogy
6 жыл бұрын
Thanks Steve. You are right about that back screw. Others have suggested the same thing or at least not replacing it reassembling. if i had to do it again... that's what I would do.
@johnwilliams8296
5 жыл бұрын
The resistor that I used in my 2004 dodge caravan looks identical,it has auto climate control,and when I replaced the resistor,it worked.Thx for the post!
@megaloogy
5 жыл бұрын
Good for you John. Replacing the resistor is what we all hope for.
@nunyabusiness1137
5 жыл бұрын
Great job explaining everything most videos always skip important parts and leave you guessing which is frustrating when you don't know what your doing. Big help thank you
@megaloogy
5 жыл бұрын
Glad you found it helpful. Thanks for the comment.
@pur914
9 жыл бұрын
Don, Thanks for this terrific video. I was able to replace the blower motor on my 2001 Chrysler mini-van (with automatic temp control) by following your nice clear instructions. Anyone attempting this blower motor replacement should pay close attention to how that "door" is popped up out of the housing. I also recommend taking needle nose pliers and pulling out the portion of the insulating pad behind the back housing screw--the one you need a flex shaft (or 1/4" drive universal joint) with 8 mm socket to remove. Pulling away all insulation in the working space gives max room for your socket and shaft to reach that back vertical screw. I watched the video several times before starting, and once during the job to make sure I had the "door" in the correct default position before reattaching the actuator motor. THANKS AGAIN--Chuck in Daytona
@megaloogy
9 жыл бұрын
pur914 Thanks for thr kind message Chuck. The one thing I wish I would have mentioned is leaving that screw out upon reassembly. A mechanis friend of mine that workes for a Chrysler dealer said they never do when they replace the motors.
@WildriceLadyB
7 жыл бұрын
Thanks Don, great video. Thought initially it was blown fuse or relay needing to be replaced but established it was the motor...annoying & satisfying
@megaloogy
7 жыл бұрын
I'm glad I could help. Hope your repair goes well for you.
@briandorff807
6 жыл бұрын
Hi Don, thank you for you video. I was able to switch out my blower in about 30 mins because of your knowledge. I really appreciated the diagnosing that you demonstrated to troubleshoot the problem, I have had an intermittent fan the last month or so and knew I had to get the problem fixed before the snow flies here in North Dakota. Surely a dead spot on the motor as it was off/on for a while with more and more off. I used a 8mm nut driver for everything except the front right screw that is right side up and had to use an open end wrench. Like several others, I loosened the 2 visible screws and the one that is easy to feel near the left rear, and then flexed the plastic until the ear broke off of the one that is too hard to get to. Not the way the dealer would have done it, but I am done now and not cussing up a storm out in my driveway. Thanks again.
@megaloogy
6 жыл бұрын
Thanks for the comment Brian. Glad you found my video useful.
@franticbob
8 жыл бұрын
Thanks! I've been living with two speed AC and Heat for 4 years. I didn't realize replacing the resistor was a 5 min fix! So awesome!
@megaloogy
8 жыл бұрын
Good news Frantic Bob. Glad I was able to help.
@TexasEx97
8 жыл бұрын
Thank you for this very informative video. Using the instructions and demonstrations provided, I was able to determine that it was my resistor that went out and not the actual blower motor. I was able to buy the part for
@megaloogy
8 жыл бұрын
Thanks Harry. Glad you had the easy fix.
@skampp
8 жыл бұрын
Thanks Mr. Guptill, exactly what I needed. Followed your instructions almost exactly for my 2005 Chrysler Pacifica and had the job done in an hour or so. Sure do appreciate that.
@megaloogy
8 жыл бұрын
Thanks Clint. I'm glad I was able to help.
@afattori316
8 жыл бұрын
Thank you for the video. Instead of trying to get that back screw out, I just wiggled it back and forth and split the tab and just pulled it out. The other 3 will hold it in just fine. Screw trying to get screw out then back in again. Otherwise everything else went well. As well as it can when your 5'11" and 235lbs. Man I hate tight spaces!
@megaloogy
8 жыл бұрын
Yes. I'm 6' 4'' and 240. I know what you mean. I never put that back screw back in and it stayed together fine. Thanks for the comment.
@fxm5715
5 жыл бұрын
Hell, yes. I did manage to get that screw out with a flex extender, but I certainly did NOT bother to put it back in.
@traviswhitlow6541
9 жыл бұрын
Absolutely great video. If you hadn't warned me about the "hidden" fastener behind the blower motor housing, I probably would have given up and taken it to a dealer. Fantastic video!! Travis
Replaced resistor and blower motor today (symptoms intermittent function of blower motor and inconsistent fan speeds) - three humid sweat drenched hours on a Houston June afternoon - was it worth otherwise $400 bill? Absolutely! lol - totally tore up the under carpet padding for the infamous "back screw" (needless to say that screw it did NOT go back in - & will buy & glue replacement padding) - could not have done without this vid - thanks much.
@megaloogy
8 жыл бұрын
Thanks for the comment. Glad I was able to help. And yes... that back screw never went back in on mine either.
@sirsweetness8332
6 жыл бұрын
Did this today along with radiator and starter. Thank you for the back screw information. I had wife start it back with smaller hands. Now church sister has front blower! Tires in the next few days. Resistor also replaced. It was burnt.
@megaloogy
6 жыл бұрын
Wow you have a project! I'm glad you found the video helpful.
@Troy-Echo
9 жыл бұрын
I'm going to be replacing my motor this week before going on vacation. The fan stopped working, but a little bump to the motor housing and it started working again for a few hours and then stopped again, and sputtered on and off. I'm guessing if the resistor was bad the motor just would flat out not work. Thank you for this excellent video. The biggest issue I see is my big hands in these little places. Thanks again!
@megaloogy
9 жыл бұрын
Noneya Frigginbezwax Thanks for the feed back. Sounds like you have a motor problem. Usually I understand that a bad resistor will cause some speed settings to fail or sometimes all settings. If you can restart a motor by banging on the housing... it's definitely the motor. Big hands is definitely a handicap working on newer cars. I too suffer from huge hand syndrome. He He. Good luck and when you put it all back together... throw that difficult screw away. You don"t need it!
@SaxualProblems
9 жыл бұрын
Don Guptill Difficult screw as in the one in the back where you need to take out the insulation? I may be lucky...I had more money than I had time a couple days before going on vacation and had to have the shop fix the problem, which I'm sure was the motor. Hopefully they left that agravating screw out for me! I'm used to this big hand problem. It started when I became a copier tech back in the 90's...I always joked that these big American hands were not made to fit in those little Japanese spaces (Minolta copiers). Panasonic came out with their new line of copiers a few years later and fixed that problem - 2-3 screws and almost anything came out in units and were easy to work on with big hands. :0) TY for the confirmation that this was indeed the motor.
@Troy-Echo
9 жыл бұрын
Don Guptill That SaxualProblems name is me...I play the saxophone, but not very well...thus the name LOL. I think my motor was good, but I replaced it anyway. Even though the motor would stop and start, when I pulled the wires from the resistor part of both had melted where there was some kind of short. I was able to pull the big plug out without problem, but I had to get vise grips to get the motor plug out because it had partially fused into the resistor, so I ended up replacing both motor and resistor. I was actually able to get that rear screw out fairly easily, but maybe I just happened to have the perfect size flexible extension, and I was using a screwdriver here, not a rachet. I didn't even remove any of the insulation, and probably could have gotten by without pulling the carpet back. Thanks for the tip on not reinstalling that same screw though, I would still be there now if I was dead set on replacing it. For me, the screw that was the bear was the downward facing screw on the right. Thanks also for the tip on putting the door back all the way to the right. I probably wouldn't have thought of that otherwise.
@megaloogy
9 жыл бұрын
Noneya Frigginbezwax I suspected it had something to do with a saxophone LOL. Interesting situation you had with the short. It could have been caused by a bad motor as well. On another site a real mechanic diagnosed a repeated resistor failure with a tired motor pulling way to many amps to run and overheating the resistor. The motor replacement fixed it so replacing both motor and resistor will be the end of your problems. Good luck and keep playing.
@scooter12368
9 жыл бұрын
you speak very clear and patiently in order to instruct others. thank you for your time and clarity. I get no motor speeds with while turning the speed control. I have read if it is the resistor i would at least get high speed only. this would indicate a bad resistor.
@megaloogy
9 жыл бұрын
scooter12368 I would agree that if you have any operation at any speed that it is probably the resistor. High speed is battery direct with no resistor in the circuit. Typically ( I've heard) you tend to loose the lower speeds as the resistors fail. They get pretty hot during operation.
@kiddflash11
7 жыл бұрын
Excellent video, Thank you. It's summer in Florida, hot. My AC is finally working. I couldn't have done it without you.
@megaloogy
7 жыл бұрын
Thanks for the comment. Glad you can stay cool. It's hot in VT. I can only imagine what Fla is like in summer.
@dashcamandy2242
7 жыл бұрын
Thank you so much for posting this video, it was very clear and easy to understand. I've done blower motors plenty before, but never on these vans. Your tip on the air recirculation door was SPOT ON, and your video was a huge help as just this afternoon I replaced the blower motor in my '05 Town & Country. I successfully did the job in about an hour and fifteen minutes, using the tools you show here (the flexible driver is a MUST-HAVE!!!). I did not need the 8mm wrench to remove the downward-facing bolt, as I was able to use a 1/4" drive ratchet with a stubby extension and socket (stick the socket/extension behind the antenna wire and it's not too bad to get out). That hidden bolt at the rear of the cage I didn't even bother reinstalling, because I didn't cut/move the carpet padding. I would recommend owners perform a HVAC panel recalibration after this job (search on KZitem or Google, it's ridiculously easy), just so the stepper motor for the recirculation door is back in sync with the control panel. If, following this video's diagnosis procedures, the blower motor is indeed at fault, I would highly recommend owners remove the blower motor resistor pack ANYWAY, and blow it out with electronics cleaner or compressed air. I have seen blower motor resistors fail due to debris *literally* burning on the bare wires, and since you have easy access to it, why not take a few minutes and clean out out, and extend its life a little bit? (As a sidenote, the metal-caged resistor pack is Mopar original, the circuit board ones are typically aftermarket and tend to not last as long, but are less vulnerable to debris.) I've rambled on enough... But let me say thank you again for the video, especially the diagnosis portion, great tips there for the novice.
@megaloogy
7 жыл бұрын
Thanks for the comment and good additional information as well. I was not aware of the HVAC calibration. I've gotten a lot of good info here from responders and I hope that viewers take a look at them.
@911zette
9 жыл бұрын
Thanks for the video! I was able to change out the blower motor by myself using this video! And I'm a 41 year old woman. Thanks again!
@megaloogy
9 жыл бұрын
911zette Thanks for the comment. I am glad it helped.
@jordannorman6071
6 жыл бұрын
I really enjoyed the video but one piece of advice that I would strongly give is to check the fuse first and replace the resistor no matter what. I followed the directions in this video to properly check the resistor and according to the voltmeter my resistor was functioning properly. I then went through the arduous process of changing the blower motor. After the new motor went in I still did not have power. So I did the next thing and changed the resistor. SUCCESS. My advice would be to just change the super easy $5 part and if it doesn't work, at least you have a brand new $5 part installed. If it does work you just saved yourself a lot of frustration. Thanks for the video! Helped a lot. Cheers
@megaloogy
6 жыл бұрын
Hi Jordan. I apologise for leading you in the wrong direction on the resistor. i was operating on bad info myself there. Power at the resistor shows that the fuse is OK but I have learned that power to the motor is actually through the ground wires on the resistor pack meaning that if the speed selector is set on a specific setting there should be power at the corresponding ground wire and the motor should operate at that particular speed. You are right about just changing the resistor first. If the motor does not run then it IS the motor and you could take the resistor back to the autoparts store and get the motor. So I hope other viewers see your comment and take heed.
@jordannorman6071
6 жыл бұрын
Don Guptill I appreciate the apology but probably unnecessary haha. Your video guided me through the process and I now have a working blower motor so that’s success in my books. Thanks for the clarification and I do hope that we save someone a little extra time. Thanks again
@TiborRoussou
8 жыл бұрын
About the dead spot, your friend is dead on! Starters are also notorious for dead spots. Thanks for sharing this video, it will make changing the fan and resister on my friends Caravan much easier :)
@peteralan2358
6 жыл бұрын
Thanks Don! After watching your video and reading the comments I was able to R&R the blower motor in my 2005 Grand Caravan in under and hour. The readers tip about breaking the tab of the 5th screw by "wiggling" (more like wrenching) the blower housing back and forth really helped save me a lot of time and agony. Especially since I did it outside on my driveway and the temp was 17 degrees.
@megaloogy
6 жыл бұрын
Fast work Peter! Glad it went well for you. If i had to do it again... I'd just snap it off too!
@Jonathan-qo3qe
Жыл бұрын
I use the French to English translation sorry if it makes it difficult to read. I have two identical 2005 van and I had the idea to make a booster pack this winter with an 18 Volt makita tool battery. with 2 wires to the pole of my battery... it actually starts very well! but this created a short circuit and caused me to no longer have a motor that pushes any interior air... (It is not my resistance because I have already needed to change this resistance and when it is the resistor the fan motor and still assuming to run at high mode only... This is a good sign to say it's your resistor which costs around 20 bucks in my experience with my van) I used this module to boost the start-up this winter on my two van and doubly created the one and same problem on both: "no more air from the fan system." so do not try to boost with any source more than 12 Volts because it can be very damaging and bypass the fuses that still work. If this caused the fan's motor to fall to the famous dead point as you say... I will try to get them out of this dead point by reactivating them like yours on your video by giving a 12 volt power supply. banging on it ... (like waking up to the engine starter which no longer starts) I know the cause which is my short circuit so it's not a question of wear and tear to neutral and in all case if they go back for testing I put them back in place to see. logically I will not see why it would not continue to work... (I personally find that the mechanics have the option of replacing a part a little too easy to my taste, it seems to me that reworking must be possible, example a few drops of oil on the shaft etc... Because the fan motor is $200...) but hey I'll run all this... track to follow I will report a feedback here on these superb fans supposedly good for trash. thank you for your video sincerely I speak French but I activated the translation of KZitem in French. Long live mutual aid! Anyone who takes the time to make similar videos... you are all good people, with a good heart! A+ Jonathan
@mdaski
8 жыл бұрын
Excellent video. Thanks. I replaced the blower motor yesterday but could not get the part that opens and closes the fresh air door back on. When I got the spindle to align with the teeth in the moving door, the screw holes would not line up. I can't get the door to move, maybe when I put the housing back on it pinched the door?IN any event, the blower works and I have ventilation again. Most of my time was spent running from store to store looking for a flexible nut driver, which nobody had. I didn't need it anyway. Managed to get that back screw out with a short socket extension and vise grip. The killer was the downward screw. There's only enough room to turn an open end wrench 1/8 of a revolution. I was half tempted to cut my wrench in half!Putting it all back together, I only got the back screw and the downward screw halfway in and gave up. Good enough!
@megaloogy
8 жыл бұрын
Thanks. Yea that door shaft is kind of a blind operation. As long as you got adequate defrost... it's easy to live with. I never put that back screw in and no problem.
@jrjc2012
8 жыл бұрын
Excellent video and explanation. FWIW, our resistor assy checked good as shown in the video and seemed to provide power to the fan motor but the fan motor didn't work. Before replacing the fan motor, we tried a new resistor assy anyway ($17 and 5 minutes vs $80 and God knows how long). The blower immediately started working again. Now just hoping the fan motor is good and doesn't burn out the new resistor. Thanks again.
@rbk7876
7 жыл бұрын
Thanks for going back over the part on the resistor at the end as well nicely done and you didn't rush while speaking ..thank you
@megaloogy
7 жыл бұрын
Thanks Rodney.
@KenSkaggs
8 жыл бұрын
Great video. You walked me through it all the way. That one hard bolt in the back- I didn't put it back in. I don't think it's that important.
@megaloogy
8 жыл бұрын
+Ken Skaggs Thanks Ken. I'm with you on reinstalling that last bolt. My mechanic friend at a Chrysler dealership says they never do either. It will be fine. Hope your blower issue is cured.
@KenSkaggs
8 жыл бұрын
+Don Guptill It is cured, thanks to you:)
@dr.gudmundssonaircraftdesign
6 жыл бұрын
Thanks. Saved me a lot of hassle. Replaced my resistor in 5 minutes flat. Total cost $12.99+tax.
@megaloogy
6 жыл бұрын
Thanks. Glad it was helpful.
@martyedge32
8 жыл бұрын
Really good instructional video. Much, much better than others I've seen, thank you sir.
@megaloogy
8 жыл бұрын
Thanks Marty. Hope you are blowing air at 4 speeds again.
@darlacreates3197
9 жыл бұрын
thank you for your tutorial. I watched and successfully changed my own blower motor and resistor after another resistor failed.
@megaloogy
9 жыл бұрын
Nurse Darla Thank you very much. I'm glad it helped.
@johnnybaldridge4379
8 жыл бұрын
Great Job! Thank you. Replaced ours for $45
@josephmartin9132
7 жыл бұрын
thanks very much 4 the details on how to remove this fan blower. I couldn't have done it without you thanks a lot.
@megaloogy
7 жыл бұрын
Thank you Joseph. I'm glad I could help.
@freddyflirt15
3 жыл бұрын
This video is SO well done! Thank you thank you thank you!!!
@HobbyOrganist
3 жыл бұрын
Great video and I'm glad my motor is good- tested it with a small 12v battery jumped onto that 2 wire plug after taking it out, and the blower turned on, so it's my resister that needs replacement
@billbobs
9 жыл бұрын
Thank you! Thanks also to pur914 for the comments. With most of the insulation gone, I really did not have any difficulty removing or replacing the back screw (using a 1/4 drive flex extension). The blower from RockAuto was $34.79 plus shipping.
@megaloogy
9 жыл бұрын
William Roberts Wow! Good price on that blower motor. Thanks for the feedback.
@dwr136136
7 жыл бұрын
I have foreseen myself swearing, throwing tools, beating down my neighbor, kicking the fender, and drowning myself in warm beer in a soggy solo cup while sitting on the porch with tears falling on my phone screen because I knew I had to do this. But thanks to you, this should be a breeze. 05 Pacifica....Here we go...thank you sir.
@megaloogy
7 жыл бұрын
You articulate a picture we can all relate to. I hope it goes well for you. Thanks for the comment.
@painterboy454
5 жыл бұрын
Thank you so much for taking the time to make and post this video! Just changed out the blower fan on my wife's 2007 Caravan and because of your video it went smooth as silk!
@megaloogy
5 жыл бұрын
Thanks DavidI'm glad my video was helpful to you..
@ChristianCountryDJ
8 жыл бұрын
Thank you so very much for posting this. Fortunately, just my resistor was bad. Your video helped tremendously.
@bryannoah7522
6 жыл бұрын
Jim Tucker the Blower motor needs replaced as well. Iam a 12 year master certified chrysler dodge jeep tech , both should be replaced at the same time the blower motor itself is what took the resister out, the motor has overheated at one point in time and needs to be replaced at the same time
@burrejo
7 жыл бұрын
I just did my sisters caravan...tear down and reassembled took me 45 minutes...but I had watched this video 5 times at work the night before and had it memorized. That one screw is a bear...I'm convinced a really really long flex driver would have been great cuz you can't get both shoulders in there to work....but if you want it bad enough you can sprawl out and shove your head in there and use a 8mm and 3" extension and ratchet..anyone should be able to do this as I'm 6'2" and almost 300 lbs....I too did not reinstall that 5th screw and threw that thing as far as I could into someone's yard as I did this in a parking lot. Good tip on removing the cover by shoving the nut driver up through the actuator motor hole....I probably would have fought with that one.
@megaloogy
7 жыл бұрын
Good job whiskey Tango. (great handle) I'm a bit oversized too. I also cant see well at close range anymore. That makes it difficult. Gjad you got it fixed and in an impressive 45 minutes!
@graydonlindskold6423
7 жыл бұрын
Don, I studied your vid and a few others as well. The blower on my 2002 Grand Caravan was clearly bad. Your video took me right where I needed to go and ... I was defeated by that damn 5th screw in the back, even with an extension ready, I just couldn't get a good turn on it. Because I'm smaller guy I thought I would have an relatively easy time. I would warn anyone attempting this to have a few band-aids ready, once that carpet and insulation comes off there's a few sharp things under there that were ripping up my hands and fingers. I will probably try this again following Affatori316's "wiggle" method. Thanks for sharing.
@megaloogy
7 жыл бұрын
Yes. I think Affatori316's method is a good idea. You may have read in some other comments that replacing that 5'th screw is not necessary so if you can break it out, it still gets the job done. Good luck with it and thanks for the comment.
@graydonlindskold6423
7 жыл бұрын
Success! "Wiggled" that housing out, apparently there were some squirrels living in there based on some of the stuff I cleaned out. Hearing a fan blowing in the front is sweet music, my cold feet will be loving life tomorrow!
@TheLokoViejo
6 жыл бұрын
You Sir are a gem thanks for the info offered here and thanks for taking the time and explaining everything.God bless
@megaloogy
6 жыл бұрын
Thanks. I'm glad you found my video helpful.
@BrilliantDesignOnline
8 жыл бұрын
thanks for the video. the easy way you explained it to the troubleshoot it helped a lot. every resistor coil is good in my resistor pack but the thermistor or thermal fuse appears to be burnt out. hopefully a new resistor pack will fix that and we get things only takes about 5 minutes to change it out.
@megaloogy
8 жыл бұрын
Thanks for the comment. Hope the resistir change fixes your blower.
@joeprincipato3540
7 жыл бұрын
Thanks for sharing your experience and know how. It will save me a ton of time and frustration. Great job!
@megaloogy
7 жыл бұрын
Thanks Joe
@Jiggs224u
8 жыл бұрын
You can try to smack the motor to see if it starts working. If it starts working after smacking it then it needs a new one.
@nassiontheworldtraveler1740
5 жыл бұрын
have that problem- so, at 275,000 miles, I'm just gonna keep smacking.
@bruceclaxton5721
8 жыл бұрын
I would like to thank you for posting this. I had the same problem with the motor and the resistor. This was a great help to anyone with this problem, because this is one son of a bitch of a job:-)
@megaloogy
8 жыл бұрын
You got that right Bruce and thanks for the comment.
@bruceclaxton5721
8 жыл бұрын
Never could get that back 8 mm screw back in, but it works fine. Been a few years in Florida with NO AC and that was a long hot haul, although it was a second car that was rarely used. Replaced that resistor a couple of times and it lasted a few days and then blew, so I knew that motor had to be bad......Thank You So Much:-)
@florincrisan5994
7 жыл бұрын
Great job Don, it really helps me a lot.
@megaloogy
7 жыл бұрын
Thanks Florin. I'm glad I could help.
@kathykhamo1059
5 жыл бұрын
Awesome video! I fixed it myself and saved over $200
@megaloogy
5 жыл бұрын
Thanks Kathy. Way to go girl!
@gromittoo57
7 жыл бұрын
Great video! No question that a flexible 1/4 inch extension would make removal of the back bolt easier (at 7:15 into the video). However, I was able to use a 5/16 inch six point nutdriver to remove that screw. 5/16 inch is slightly bigger than 8mm, so the nutdriver was able to turn the 8mm screw head at a slight angle. Using a nutdriver might even eliminate the need to remove the padding.
@megaloogy
7 жыл бұрын
Good advice Gromittoo. Thanks for the comment.
@r00zTa
8 жыл бұрын
Great job on the video. Thanks for taking the time. I all ready changed my resistor but that's not the issue. I do have power to the motor but won't move. The "dead spot" makes total sense. Thank your bud for me too. Haha.
@megaloogy
8 жыл бұрын
Thanks for the nice comment. I'm glad I was able to help.
@drazenfx
8 жыл бұрын
Very informative video. Based on the video I was able to replace blower motor.
@megaloogy
8 жыл бұрын
Thanks Drazen. I'm glad so many have found it helpful. I use you tube quite often to research fixes around the house and shop.
@ctloyd640
7 жыл бұрын
Great job! Followed the video knocked it out in about an hour.
@megaloogy
7 жыл бұрын
I'm glad my video helped. Good to give back a little for all of the "how to" posts that people make. Iv'e benefited much more that I've shared.
@jefftucker5809
4 жыл бұрын
If you want to avoid tearing the insulation away from the wheel well because its glued to it, use a small pry bar that will fit behind the blower motor or your finger and just pull a few pieces of the insulation away from below the screw area.
@edpanich2079
6 жыл бұрын
The Best video I have seen for the blower motor and actuator replacement. My actuator was bad also. Thanks. Got anymore videos?
@megaloogy
6 жыл бұрын
Thanks Ed. I'm glad my video helped. I have other videos but they are not automotive related. I would refer you to "South Main Auto Repair". Unlike me, this guy is a professional mechanic and makes great videos on just about everything.
@renemessier6335
3 жыл бұрын
Thank You Donny for the great video and explanations.
@patrickharrand
8 жыл бұрын
Don, Thanks so much for taking your time to produce this very informative video. Much appreciated.
@megaloogy
8 жыл бұрын
Thanks Pat. Glad to help.
@darrinrubrake516
5 жыл бұрын
Just a note, I checked for power like you said. Had power so changed motor. still nothing. Called a friend and he said you need to check ground to resistor not the frame. Checked power with ground to resistor, no power. Now I either take back apart to return motor or eat the cost of the motor.
@darrinrubrake516
5 жыл бұрын
otherwise it was a great video, thanks !!
@Johnnoway
6 жыл бұрын
Thank you for your time and detail saved me alot of time
@megaloogy
6 жыл бұрын
Thanks. I'm glad you found it helpful'
@vancouverman4313
4 жыл бұрын
One thing I couldn't stress enough is to remove the positive battery terminal before you do any work on the electrical system of the vehicle, the damage you can do with a screw driver that touches the wrong two wires together could be a lot more than you are saving. You also don't want to take any chances with setting the air bags off as they could kill you.
@megaloogy
4 жыл бұрын
Good advice Vancouverman. Thanks for the comment.
@mf1scher
7 жыл бұрын
Thank you for this very informative video and commentary.
@megaloogy
7 жыл бұрын
You are welcome. Hope it is helpful to you.
@jefftucker5809
4 жыл бұрын
Thx for the great detailed vid. Sorry you broke the door but you helped the rest of us keep ours in tact. I liked and subscribed with notifications in hopes you do more repair vids on this vehicle. Mine is an 01 Chrysler Voyager and the blower assembly etc is exactly the same.
@ozzylozada9653
8 жыл бұрын
I appreciate your thorough explanation. Thanks
@megaloogy
8 жыл бұрын
+Ozzy Lozada Thank you.
@victorroman7753
4 жыл бұрын
Thank guy my kids are happy with the heat God bless
@timothyhobby6546
7 жыл бұрын
Thanks, very informative. Will use the info when troubleshooting my 06 Caravan. Thanks again.
@megaloogy
7 жыл бұрын
Thanks for the comment Tim. Hope your fix goes well.
@YourCreatorGod
4 жыл бұрын
Thanks for your video you helped me greatly . Thank You so much.🌹🙏✌
@angelwithgoldenwing1
8 жыл бұрын
Thank you so much i actual changed out my own blower motor with your help and I am a GIrl
@megaloogy
8 жыл бұрын
Good for you. of course you already know being a girl is no handicap. Thanks for the feed back.
@canadiankays
9 жыл бұрын
Awesome job. Thanks so much, you saved me money and time!
@megaloogy
9 жыл бұрын
Thanks Brian. I'm glad it helped.
@jefftucker5809
4 жыл бұрын
Also for me, a knuckle joint behind the socket worked better than a flex extension.
@jesussavesseq
3 жыл бұрын
Thanks for posting this video
@crismartinez5272
5 жыл бұрын
Great video. very informative and easy to understand.
@brucehartman23
2 жыл бұрын
the only problem I had was, the connector to the resistor was different. There are 2 styles one has a blue cap on it the other one is slightly larger also. instead of splicing the wire i got the resistor that matched the new blower motor. the connector for the controls is the same. I did this because the blower that I needed was $200.00 more and, I would have had to wait 1 week to get the correct one.
@boydmerriman
6 жыл бұрын
I am having problems with my front fan, not my back fan. I checked the relays under the hood by switching them around (front to back, back to front) and the back fan still blows while the front does not. I can make adjustments to the directional dial and it will allow air flow (some) to their designated vents, but the blower for the front will not run. It was working one day, the next day it was not. This will affect both heating and AC. Again, back blower works fine.
@megaloogy
6 жыл бұрын
Hi boyd. The front heating and cooling controls are independant to the rear controls. each system has it's own blower and resistor pack. if your front motor wont work on any speed setting, then it's likely that the motor is bad. Resistors tend to fail a speed setting at a time rather than all at once. You can try replacing the resistor first and if it doesn't cure the problem take it back and exchange it for a motor. Good luck!
@boydmerriman
6 жыл бұрын
Thank you! I had a feeling it had to be something like that, but wasn't sure if there was a separate motor or not. That should be logical that there is one. I just didn't want to spend a lot of money guessing and ripping out parts that don't need to be pulled. Again, thanks!
@tonyinmepo
Ай бұрын
Use jumper wires to the motor, actually I use a pig tail cut out of a junkyard vehicle, most of the time it's the resistor
@josephmartin9132
7 жыл бұрын
I thank the Lord for your help.
@donnienicholson6062
4 жыл бұрын
Those screws in my resistor aren't screws.They look like plastic rivets or something.When my new part comes from Geek Auto I guess I'll find out.Nothing a hot glue gun can't fix if they're not replaceable.Great video on testing procedure.
@donnienicholson6062
4 жыл бұрын
Actually they were factory reject screws with maybe a mm of head.Hard to remove but easy to replace with new screws.
@megaloogy
4 жыл бұрын
@@donnienicholson6062 Hi June. Good! glad you could replace it yourself. Hope your blower is working good!
@floorcraftinstallation5156
9 жыл бұрын
Don, this is the best well documented video I have seen - THANK YOU! How did you test the relay?
@megaloogy
9 жыл бұрын
+Floorcraft Installation Thanks for the comment. In the fuse compartment there are a few relays that are interchangeable so simply replace the relay related to the heater and see if it works again. I'm not a mechanic but a mechanic I know says it's very unlikely it's the relay at fault.
@fidelr599
8 жыл бұрын
great video it work for me I just need to replace the rear one but I don't know where is the part located in the van. ..
@guyonearth
7 жыл бұрын
I would strongly suggest getting an OEM unit from a dealer or parts jobber. The replacements sold at auto parts store chains tend to be cheap Chinese generic motors that have poor quality control and often don't meet the specs of the original part. I've had repetitive problems with these parts. Brand names mean nothing. A sure warning sign is a motor that doesn't match the original and wants you to cut and splice your original plug on. Don't waste your money. If you're short on cash, another solution would be to get one from a salvage yard, it will probably last longer than the "new" one will.
@megaloogy
7 жыл бұрын
Good advice. My vehicle was 9 years old with 140k on it so the factory original lasted a good while. I would just add that on older vehicles with a short life expectancy, the cost of an OEM part may not be the best choice for those on a tight budget. Thanks for the comment.
Пікірлер: 318