Very helpful this is going to be my weekend project!
@LowkeeLT
4 жыл бұрын
Super straight forward! Loved the video, and love the fact a new clutch is easy to install!
@richb8888
2 жыл бұрын
GREAT video my man! You made it look really easy to do. I hope you have more "how to" repair videos on your V Star.
@pcascio
7 жыл бұрын
Great job -- good camera shots, and very well explained. Thank you.
@earnestbrown2643
8 жыл бұрын
Great video, however I was under the impression that the lock nut & washer on the pressure plate had to be removed and the pressure plate bolts had to be turned 2 turns (loosening or tightening) at a time . I just put mine back together yesterday and do I have to go back inside and adjust the #1 Push Rod which is a very important step to get it ADJUSTED before you even put the cover back on. And Don't over tighten the Pressure Plate Bolts or the Clutch Cover Bolts, both should be snug, or you will strip them and on the pressure plate I had a friend helping and the damn pressure plate (2) bolt broke off at the clutch basket and it cost like 2 times as much to replace the springs and the basket!
@TheKylebreezy
4 жыл бұрын
Damn good video bud! Ya made it look easy. Plan on doing mine soon and will be using this as a guide!!. Ride on and ride safe brother!👊👊
@Ilihiafarris
4 жыл бұрын
Thanks for the tutorial. I feel confident to replace my clutch on my 2000 v star 650. But...Damn, I just changed my oil 2 weeks ago. Well, another oil change coming soon.
@TheKylebreezy
4 жыл бұрын
Atleast you can reuse the filter.
@joaopaulovitorsantos3382
3 жыл бұрын
Amazing work , I will be doing this next week when my gaskets arrives.
@paulacabbo466
8 жыл бұрын
you lined up the groves to each other on the friction discs but didn't tell people that the double notches on the friction discs go in between the two indicator dots on the basket, this is extremely important, or clutch drag will occur when the oil gets hot
@cheese-money2748
5 жыл бұрын
So there is a very particular placement of each friction disc?
@americanmuscle3090
2 жыл бұрын
You put the oil filter in backwards
@mikechapman7748
4 жыл бұрын
Best clutch plate replacement video yet made it look simple but would drain oil and buy new I just dont like the mess
@SuperJAWman
2 жыл бұрын
You pulled the clutch out and noted the bevel side facing in, then you noted the bevel side facing out when installing the first steel plate lol. Guess it goes to show it probably doesn’t matter. Nice video.
@whobru
5 жыл бұрын
great info! nice job with the camera too.
@7316bobe
5 жыл бұрын
Best to drain the oil out of the engine first. You got in a real mess there.
@zserub
2 жыл бұрын
Lights are weak but the music is perfect.
@dannyburgess2781
4 жыл бұрын
Very well done. Thank for. Thank and make it look so easy but one thing if any. Temp to do this watch careful watch it more then just once look at. The detail very wisely you dont over look what very important. Look bolt goingback they all different size and make sure clean your hand are glove are clean and dont wal way from it uncovered for sure if tire in to. You got put it back. If dont part be come up missing and you end up. With bike that not running because you dofnt finished so make sure you got all your part gasket and filter. Before hand
@iangroover1188
3 жыл бұрын
..what?
@jbreviewer65
Жыл бұрын
I stand corrected, the Oil filter goes the opposite way on the 1100. you installed it correctly for the 650. Sorry!
@sherbettt
5 жыл бұрын
Hello. Please confirm how to regulate push rod #1 after installing the new frictions disks? The full package of disks became thicker and push lever is in wrog position as you know. If you turn it clockwise, then we will not have a stock on the thread.
@williamwood7936
Жыл бұрын
Great video, thanks
@chriscalderon2579
2 жыл бұрын
What are the torque specs for the springs
@hkk3656
5 жыл бұрын
I don't think this guy is making videos anymore. Hope he starts back up.
@bvgb921
3 жыл бұрын
You said the bevel goes inwards when you took out the plates, then when installing the new plates you put the bevel on the outside ? So you installed them the wrong way round.
@tylercarder581
3 жыл бұрын
Great Video! 👌
@Stover159
3 жыл бұрын
do you HAVE to remove the exhaust? the reason I ask is because my exhaust studs are rusted so bad there's not even threads showing its just a rusted shaft
@Archermotorcycleandtire
2 жыл бұрын
Same procedure for a 1100 classic?
@americanmuscle3090
2 жыл бұрын
Yes
@HighAway
2 жыл бұрын
I was wondering if this bike could have an open primary clutch belt assembly?
@Sandman66
6 жыл бұрын
After installing the new clutch did you adjust the bottom end adjuster..on opposite side of bike...
@christopheroconnor2696
3 жыл бұрын
The rings with the teeth and the friction plates do you put them on ring then friction plate, so forth and so on?
@billsaylors2950
4 жыл бұрын
I have a 2003 V-Star and changing the starter clutch but I've lost one of the small rod that goes into one the 6 springs how can I get a replacement
@jaymartinson3236
6 жыл бұрын
woah... all that to get the oil filter out? im glad they changed that with the 1300
@Jason32Bourne
5 жыл бұрын
It's only about a third of the whole process shown. kzitem.info/news/bejne/2oWcu6t-sp-KpGU
@PedroRamos-uw1fe
6 жыл бұрын
No grooves on my plates. Now what?
@Lgn26point2
3 жыл бұрын
The music, you really don’t need it, lower volume is better, it’s not bad, just gets annoying and redundant, I am not being critical but just feedback.
@xxscrewthesystemxx2562
3 жыл бұрын
No its good 😎
@mattbaugh8966
7 жыл бұрын
pj what's the torque specs on the springs?
@TheKylebreezy
4 жыл бұрын
Consult the manual. Please
@SuperAsianDude1
7 жыл бұрын
how did you prop it up straight?
@paulnmillerjr
7 жыл бұрын
James Kang I had a bike stand
@bretthull378
3 жыл бұрын
What pipes are those?
@cheese-money2748
5 жыл бұрын
I have a virago 250 2007 and i need a very detailed tutorial on a virago clutch replacement.. especially detailed info on friction plates placement
@BobbyAlverson
4 ай бұрын
Is the clutch different in a custom an clay
@BobbyAlverson
4 ай бұрын
Is the clutch different in a custom an classic
@Kdsound
7 жыл бұрын
get some T allens dude
@jbreviewer65
Жыл бұрын
You put the oil filter in backwards.
@docyoung81
6 жыл бұрын
Was this your first time
@travisgilliam5
6 жыл бұрын
How many miles did you get out of that bike before you put the new pads in?
@docyoung81
6 жыл бұрын
I got all most 17k and thinking on putting in a performance clutch in
@jasonchicoine4282
Жыл бұрын
White lithium grease on the gasket
@johnnypavon297
2 жыл бұрын
Hello brother , i did the clutch like u xplain but now when i put in drive engine turn off
@johnnypavon297
2 жыл бұрын
Can u help me with the problem
@alexanderacousticguitars
Жыл бұрын
Mine does that after just an oil change. Try letting it idle a while and get hot to circulate the oil since it’s a wet clutch
@joederue2392
3 жыл бұрын
Cost of clutch kit.
@pickypoint640
2 жыл бұрын
$90 - $140 for factory parts.
@denmalski
5 жыл бұрын
if your changing the oil anyway I would just drain through the drain plug then have at er
Пікірлер: 61