Thank you so much for very understandable videó sir! That "turn to clockwise to loose" screw made a full sunday of headache for me. You made my happy :) Thank you again and I wish you good health! Greatings from Hungary
@NoName-tq9fi
Ай бұрын
If anyone is going to do this, I strongly advise you replace the tone ring while you are at it. That is the press fit steel piece with the dozens of little rectangular cutouts around the outside. This is what the wheel speed sensor for the ABS brakes uses to measure axle speed.
@LucienDevaux
3 ай бұрын
Thanks very much sir. I'm not very good in English but you speak slow and I can enderstand. Thanks a lot, God bless you. I'm from Madagascar.
@СергейАндреев-б1ш
5 ай бұрын
На подшипнике нужно удалить внутренний пыльник чтобы к нему поступала смазка.
@СтасЗенкин-у1ы
Жыл бұрын
Привет дядя у меня тоже такой DODG SPRINTER только жёлтый завтра пойду менять кожух тормозного диск ка с колодками видео понравилось всё понял. Ok😊
@aijja456
2 жыл бұрын
this is a really cool technique to remove the bearing (Y)
@glenwelsh402
Жыл бұрын
Thanks for the video. Really good information. Question: If I did not have a press to put the bearing back on, I reverse your technique of removing it?
@pappawsnothingbettertodovi1985
Жыл бұрын
I personally would NOT try that. If you were to do it that way, it would be putting pressure on the outside of the bearing. That could possibly break the bearings out of their housing.. That is why I suggest pressing the inside part of the bearing. That way there is no pressure on the outside housing.
@hunorroot3869
8 ай бұрын
great video, I have the same seal leak why did you remove(hammer on) the sheet metal holding the seal? replacement kit I got doesn't include the metal part only the thick rubber seal
@pappawsnothingbettertodovi1985
8 ай бұрын
I am not real sure what you mean. The seal that I replaced has the metal ring and rubber gasket all one piece.
@drexelspivey6472
5 ай бұрын
thanks for a great video
@humanresource9659
Жыл бұрын
Priceless....
@rogerstenbro1051
Жыл бұрын
nice work
@vadimmarin7524
Жыл бұрын
А гребёнку можно менять?
@ЮнесЮНЕСКО-ю3ц
2 жыл бұрын
Здравствуйте. Номер, размер гаечного ключа который затягивает гайку подшипника скажите!
@pappawsnothingbettertodovi1985
2 жыл бұрын
I bought my tool on eBay. Please search eBay for this description. (FIT MERCEDES SPRINTER REAR AXLE LOCK NUT SPANNER WRENCH TOOL FITS 9023570126 NUT)
@hifartingoctopuss
Жыл бұрын
Hit it with a punch to tighten it lol
@jamesward5721
Жыл бұрын
What us peasants who don't have a slide-hammer bearing puller yokie do is put 2 over-long bolts into the stud holes & wind the sucker off using those & an impact gun.
@AngelSanchez-du8ze
Жыл бұрын
What’s your trick for pressing the bearing into place?
@СергейАндреев-б1ш
5 ай бұрын
Отрезок трубы подходящего диаметра
@andyking9673
2 жыл бұрын
why 2 splined areas near the diff?
@pappawsnothingbettertodovi1985
2 жыл бұрын
I have no idea. I saw other video's that state they have no idea either. Good Question.
@user-hp3ob9fh5i
Жыл бұрын
В этих мостах ставят блокировочные втулки ,для полной блокировки моста !
@pauldailey4477
Жыл бұрын
Probably something to do with lubrication.
@NeverMe84
3 ай бұрын
The rear diff lock (if you have one) engages with those outer splines
Пікірлер: 27