Followed your video step by step and only took me 2 hours . I'm 62 so I guess that's not a bad time . Thanks for your help. { No old people were hurt during the installation of my CV axle.}
@charlesbosse9669
25 күн бұрын
Thank you. Great video. Can't wait to see the next one
@MarshallKnowlton-pf7xq
7 ай бұрын
This guy saved me some time on taking the axle out the other videos of popping the ball joints out is not the way to go! I find just removing the caliper and hanging it off out of way and not worrying about speed sensor are two changes I made that worked fine!
@USBCablez
7 ай бұрын
Thank you so much. Your video was very useful. My cv axle went out yesterday on the way to work. Following your video was informative. And made making the job a lot faster.
@memoobaba
6 ай бұрын
Great informative video, could also do a strut replacement while at it and change the sway bar links
@petrusincraian198
11 ай бұрын
Thank you. Great job.
@JTapia512
Жыл бұрын
Great Video. I like using that screw driver trick when i torque the axle nut
@MarshallKnowlton-pf7xq
7 ай бұрын
I did that and broke my screwdriver shaft in half I freaked out I thought I messed up the rotor and caliper
@MarshallKnowlton-pf7xq
7 ай бұрын
Best to loosen axle nut while tire on and someone applying brake while on ground
@wilbertallen5190
5 ай бұрын
It was very helpful thanks
@sandramargolis
7 ай бұрын
wow ! if it wasn’t rainy all week, i might have try doing it myself. Your video is awesome ! thanks also, i’m curious to know how much “they” usually charge for this kind of job !? thanks
@ValleyMobileAutomotive
7 ай бұрын
Depending on where you live and the shop's hourly rate you can expect around $300-$500.
@100mphClub
Жыл бұрын
Part number for the seal? I need to replace mine after not seating the CV shaft enough.
@willkrzymowski7197
5 ай бұрын
Thanks!
@ValleyMobileAutomotive
5 ай бұрын
You're welcome! Glad this was helpful 👍
@KrashTWazo
Жыл бұрын
Already subscribed
@jcperez2861
3 ай бұрын
I put the new cv axle, but is dripping oil, need the ring right?
@ValleyMobileAutomotive
3 ай бұрын
First make sure it's seated all the way in. If it is still leaking then yes a new transmission output shaft seal is needed.
@joecox9958
Жыл бұрын
I went for wheel alignment, told if I use your method I need redo alignment
@ValleyMobileAutomotive
Жыл бұрын
You shouldn't need an alignment. There isn't a camber adjustment on the struts. They are unbolted and rebolted back in the same place. So nothing gets out of alignment. If you are replacing the struts with new ones then an alignment would be a good idea 👍
@USBCablez
7 ай бұрын
Lmao I didn’t van rode nicely and didn’t have a problem Your van might have already needed a alignment
@ilmirGareev88
2 ай бұрын
please tell me what kind of grease and where did you apply it?
@ValleyMobileAutomotive
2 ай бұрын
@@ilmirGareev88 Links are in the description. I believe I just put some on the inner shaft splines. You can use anti-seize for the outer splines 👍
@ilmirGareev88
2 ай бұрын
@@ValleyMobileAutomotive thank you very much, but what is the dielectric grease from the description for?
@ValleyMobileAutomotive
2 ай бұрын
@@ilmirGareev88 I just re watched the video. The dielectric grease acts as a lubricant so the seal and cv axle slide in easier. Don't use anti-seize on the inner axle splines.
@ilmirGareev88
2 ай бұрын
@@ValleyMobileAutomotive thank you!!👍🏻
@jamesguralski5156
Жыл бұрын
Should take apart lower ball joint to do this job. That way you don't have to do an alignment!
@ValleyMobileAutomotive
Жыл бұрын
Hey James, thanks for your comment. Removing the ball joint is another way to tackle this repair. No alignment is needed after removing the lower strut bolts 👍. There is no camber adjustment on these vans. The toe is not affected as the bolts can only line up one way. So it goes back together exactly how it came apart just like removing the ball joint 👍
@USBCablez
7 ай бұрын
How do you figure this will make for an alignment? I followed his video to replace my cv axle and it worked great. And I didn’t need a alignment
Пікірлер: 29