Awsum video step by step ez 2 follow along N replacing da pcv valve gud idea Mahaloz n Alooooooooha 🤙🏾😎✨👊🏾
@1995dresser
6 жыл бұрын
I have a 2005 and Mine Leaked at 80,000 in the back corner. a New Gasket set and just a light coat of RTV on the head and use a nut driver to Tighten . the cover has stop tabs molded in so you can't over tighten it as soon as the cover contacts the head stop
@johnazzara8212
Жыл бұрын
Good video. One question. What should this job cost to have done? Thank You.
@tonychavez933
3 жыл бұрын
Tank you so much for the great information made it easy to do my job
@kennymartin379
Жыл бұрын
I like the 2.4 better
@Scubastevetampabay
2 жыл бұрын
DO NOT!!!! Use carburetor cleaner around any oil under that valve cover unless you plan on running that engine for 1 minute then changing the oil. Any solvent will change the viscosity of the oil which could potentially damage the motor. Instead use a razor blade to remove the gasket and wipe in an outer motion so you do not get any material inside the motor.
@mkrp4
Жыл бұрын
The carb cleaner is not used directly; it's spayed on lint-free rag to wipe the surface. Using red silicone under rubber gasket and disconnecting battery like shown in this video will cause me to get fired on the spot. Take negative wire out ( not really necessary to do for this job) and cover exposed battery terminal.
@gilbertoramos5137
4 жыл бұрын
What are the torque specs for valve cover bolts"
@marsal1903
4 жыл бұрын
What's the torque sequence
@chenviejo
Жыл бұрын
Hopefully you can answer my question: What's the torque recommendation? You did not mention that. Thanks
@kennymartin379
Жыл бұрын
Watch Scotty Channel he says just get them real tight
@thelion9863
4 жыл бұрын
Why size of socket did u use to put the pcv was it a 7/8
@stuartdavis1310
5 жыл бұрын
Why did you replace the pcv valve?
@johnmcdonald4747
5 жыл бұрын
A bad PCV valve will damage your valve cover gasket
@nathanrice1796
2 жыл бұрын
Pretty informative.
@gajc89
6 жыл бұрын
no replies but ill try anyway. got a link for the parts used? the gasket sealer and the gaskets themselves?? thank you
@louisgaragediy923
6 жыл бұрын
Hello there. I do not have a link for the parts used, maybe trying a local car junk yard you may find some. If anyone know share the link here. I purchase all my gaskets and gasket sealers at a local auto store.
@jehan0
3 жыл бұрын
Which size socket for the PCV valve?
@chrisjarvis4449
2 жыл бұрын
the one that fits
@reboureyn139
6 жыл бұрын
Un-loosen would be tighten, wouldnt it ?
@louisgaragediy923
6 жыл бұрын
you are right. I will work on that lol.
@jamiejackson1452
7 жыл бұрын
Hey what about the ignition coil order assembly does it matter which order or not? we had a mix up of the order.
@louisgaragediy923
6 жыл бұрын
Hello Jamie, I believe the coil order may not matter but then again I never had this problem. I always but everything in a certain order to avoid anything being mixed up. I am sure you figured it out by now. Let us know. Thanks.
Пікірлер: 24