That's quite a job to be doing on the side of the street. Very impressive. Good job!
@codycarlson9441
11 ай бұрын
Thanks brotha🙏
@outcome2715
6 ай бұрын
hell yeah salute , had to replace a knock sensor on a huinday sonata took a fat min did it in the parking lot in front of my recruiters recruiting station 😂🎉
@scottnbecky1
8 ай бұрын
You did a good job on this video. Thanks for your help
@kalaichallvam259
8 ай бұрын
Thanks for the video Cody. Gave me great guide in removing an R20A engine from my 2009 CRV. Great video. Thanks
@joshterrell6886
Ай бұрын
Ironically im watching so i can out that in
@richiewijaya2126
6 ай бұрын
TERIMAKASIH SUDAH BERBAGI CERITA UNTUK CIVIC FD SAYA PENGGUNA CIVIC FD1 MT FROM INDONESIA KUPANG NUSA TENGGARA TIMUR 🙏🏻🙏🏻 SUKSES FOR CHANNEL
@texaslawdawg1902
11 ай бұрын
Just found out my son’s Civic (2008) has the infamous cracked block, smh. Great video. Starting my search for a 2010-11 engine.
@hoobered1232
11 ай бұрын
me also. Where on the same job searching for info. I found a 2011 55,000 mi. junk yard engine. DIYer.
@codycarlson9441
11 ай бұрын
Aw man these freakin 06-08 R18 motors haha I swear….I wish you the best of luck👍
@renj6531
5 ай бұрын
I have another car now but when In the process of replacing my R18 s cracked oil pan i saw web cracking at the bottom end of the combustion chamber around the piston. Idk if this is where the engines crack, but either way it wasnt good.
@joshadofo7819
7 ай бұрын
Great video bro 😊I love this
@k3nto240
7 ай бұрын
Awesome Job Cody! I am gonna JB weld my crack for now until I figure out what I am going to do for the long term. Hopefully it will hold during the winter months. Been running water in the radiator for a few months now.
@codycarlson9441
7 ай бұрын
I also temporarily used JB weld and it held up strong
@SmiteKillzz
4 ай бұрын
Awesome work brother, I just bought a motor 50,000km out of a 2010. Someone’s grandma got hit in the passenger rear. My motor has a worn out connecting Rod Baren smh 280,000km
@frias2287
5 ай бұрын
Nice one bro
@nikolaarutyunov1808
4 ай бұрын
well done buddy,next time you can use a jack a lower the engine first to unbolt the crankshaft just do not remove driver side mount and lower a motor a litle bit so you have acces,because sometimes even realy strong impacts do not work,i tryed on same civic 2007 last time !050 psi from harbor frights it did not work,so i had to use a hoge bar with 3/4 drive and it come out
@codycarlson9441
4 ай бұрын
Yeah those crank bolts are tough to break. Impact only worked for my situation cause I have removed it in the past already
@dademurphy3062
3 ай бұрын
Did you have issues with your throwout bearing being to short? Normally the jdm engines are auto and need a larger bearing?
@codycarlson9441
3 ай бұрын
Mines auto so I wouldn’t know on that one. I would imagine the flywheel pressure plate would bolt right on tho
@drewaspark
4 ай бұрын
Looking for info on a Honda 1.8L R18A/R18Z Engine conn rod & main bearing code. Anyone have idea where it would be stamped on the block or maybe on main bearing bridle? I have a 07 Civic DX & am dropping in a 2010 1.8L due the OEM Manufacturing problem of Poor Casting Issues on the 2006-08 & early 2009"s Civics with 1.8L in them, which leads to leaking Coolant. I wanting to do a bearing roll-in before I drop in the 2010 1.8L engine into my car.
@icemanjt2430
Ай бұрын
a 07 never had a cracked block 😂
@OppositeOfMute
Ай бұрын
Do you think this is close enough to a 2013 Honda civic that I could follow along and it still be applicable?
@codycarlson9441
Ай бұрын
Definitely!
@evedits3174
8 ай бұрын
Mine cracked at 200k miles and been driving for about a year with crack i added k seal fixed mine for a bit but now my radiator hose is collapsed i wanna replace engine but afraid of warrenty on engine whats the best place to buy a jdm engine online
@codycarlson9441
8 ай бұрын
I’m not sure. I would recommend buying locally if you can. But there are a lot of online dealers on eBay if that helps at all
@josexivir4260
6 ай бұрын
Hi Do you know if the jdm engine does not have the same issue with the coolant leak on the block?
@codycarlson9441
4 ай бұрын
JDM engines didn’t have defects in the casting process. Also all have 60k miles or less for most part
@Omarvro1
4 ай бұрын
Did you use the original wiring harness and swap it over to the jdm engine?
@codycarlson9441
2 ай бұрын
Yes
@luisrodriguez-gc4xp
23 күн бұрын
Where did you buy the jdm motor from? Looking for a replacement rn
@codycarlson9441
23 күн бұрын
Redline JDM in Ontario CA. Highly recommend them
@bonaminhrasmey42
8 ай бұрын
Why did you remove the engine 😊
@BACONNWRAPPED
2 ай бұрын
How the motor crack? Where? Anything u could do to prevent it?
@codycarlson9441
2 ай бұрын
At the casting lines in the back. Most crack in the front. It was a manufacturing defect
@BACONNWRAPPED
2 ай бұрын
@@codycarlson9441 i bought a used 07 and it has 240k miles on it.. im wondering if that defect has already been taken care of by now or im living on borrowed time...
@josuedelgado2524
Ай бұрын
My block is crack 😢
@pjbth
5 ай бұрын
Ok but why? 😂 They are the same thing as a usdm one, though i guess the JDM ones probably have lower Km's
@codycarlson9441
5 ай бұрын
US had defects in the casting
@lexington739
11 ай бұрын
After you put the jdm motor everything worked find.
@codycarlson9441
10 ай бұрын
Yep! Runs solid
@mcspliffersongaming2332
5 ай бұрын
So these engines got a crack in the block through years 06-08 huh? Hmm my cousin is selling me a honda for only a grand going to have to see what year it is the car is for my brother it will be his first car
@emoryflores7769
5 ай бұрын
Not always. It is common though. They are very amazing cars other than that.
@BulliKid
10 ай бұрын
Where as your leak
@codycarlson9441
10 ай бұрын
It was on the backside by the PS pump
@BulliKid
10 ай бұрын
@@codycarlson9441 possible to weld?
@codycarlson9441
10 ай бұрын
@@BulliKid initially I used jb weld to seal the oil leak and it worked. But it was cracked thru oil and coolant passages so I figured it was time
@BulliKid
10 ай бұрын
@@codycarlson9441 oh yah if it’s mixing with oil it’s done :(
Пікірлер: 48