Great and informative video. Word to the wise, using a "crows-foot", the opening has to be 90 degrees from the torque wrench for the proper torque. Straight on the torque is actually higher. Side note: If the fuel lines are stainless, they are more forgiving and can be tightened a bit extra for positive sealing.
@treyhaberman
6 ай бұрын
Yes sir I figured it would be a little less with the crows foot. The online calculator would call for 5 to 15 lbs difference, but everytime you reset the the ratchet it applies difference force. I just tried to keep them as equal as possible and watch for leaks.
@jeffreypinder9398
6 ай бұрын
@@treyhaberman Well done!
@briansnyder1276
5 ай бұрын
Great video, very detailed thank you
@treyhaberman
5 ай бұрын
Thanks man, appreciate it
@ginahampton2129
9 ай бұрын
Awesome!!
@treyhaberman
9 ай бұрын
Thanks!
@patrickmolloy9828
5 ай бұрын
Awesome thanks
@treyhaberman
5 ай бұрын
Welcome bud
@matt1560
8 ай бұрын
Sorry just read the comments and see you bought some good video
@treyhaberman
8 ай бұрын
?
@wildcard2668
9 ай бұрын
Which company is better to buy the fuel injectors from S&S or BD Diesel . Good Video learned alot
@treyhaberman
9 ай бұрын
This was my first time buying injectors, but I can say S&S was more personable to deal with than exergy. I knew that the previous owner installed Exergy injectors, but when I contacted them, they weren't any help. S&S not only walked me through the testing process to make sure my issue was the injectors, but took the price of testing out of the cost of the injectors. I just choose my brands based off of 5.9l cummins forum suggestions and I wasn't disappointed.
@dougtaylor5533
7 ай бұрын
Great video / walk through. I am curious, you cleaned the valve cover, but why didn't you clean the lower portion as well (only did injector holes)? (note, I don't have any experience doing this, so honest question) I suspect it is difficult to do (or high risk of making the situation worse). Thanks in advance, I have saved and will watch before I attempt.
@treyhaberman
7 ай бұрын
I didn't want to risk contaminating the engine, since I wasn't removing the head. That's why I just spot cleaned what I was working on.
@Mike-vu9xf
4 ай бұрын
Trey, what would an owner expect to pay for a job like this? Parts and labor.
@treyhaberman
4 ай бұрын
Not sure how much buddy. I wanna say probably around 4k
@TheOne-ts6lf
6 ай бұрын
Nice video, great detail what manual do you have and where did you get it?
@treyhaberman
6 ай бұрын
It's a Haynes manual from autozone
@TheOne-ts6lf
6 ай бұрын
@treyhaberman thank you sir.
@treyhaberman
6 ай бұрын
@@TheOne-ts6lf welcome
@ryanclarke2161
8 ай бұрын
How do you make low sulphur diesel?
@treyhaberman
8 ай бұрын
I work in a HDS (hydrodesulfurization) unit at a refinery.
@kurt8986
5 ай бұрын
what's ur turbo setup I'm only at 38 psi with a taterbilt 63.67 and 100hp injectors/10mm cp3 on an 06 cr
@treyhaberman
5 ай бұрын
369 borgwarner 30% over s&s injectors Fleece cp3 with airdog 165 4g lift pump Efi live tuner T4 steed speed intake 5" mbrp quiet exhaust
@kurt8986
5 ай бұрын
@treyhaberman awesome video buddy, that's cool is that normal for thet setup that boost # is hi i love it, is the waste gate just set low on mine to be at 38 psi I just prob so a smoke test
@treyhaberman
5 ай бұрын
@@kurt8986 yea the wastewater might be worth looking at. How are your egts?
@babybullsmith001
7 ай бұрын
How much did S&S injectors ? Thanks
@treyhaberman
7 ай бұрын
3288.93 for 30% over. That was also 30$ per injector to test my old ones.
@babybullsmith001
7 ай бұрын
My remans are at 130,000 miles with each of my fill ups ,I treat my fuel with optilube xpd. How long will these injectors last? Your geuss@@treyhaberman
@treyhaberman
7 ай бұрын
@babybullsmith001 you can never guarantee how long they will last. I got some diesel algea in my tank from a bad fill up and it made it past my airdog filters. S&s did say I had bad solenoids though. This is my first time using them, so we will see how long they last. Their customer service was great. I can vouch for that.
@yueningwei3679
4 ай бұрын
hi how can I contact you?
@treyhaberman
4 ай бұрын
Treyhaberman@gmail.com
@pedcas5715
8 ай бұрын
Thanks for the video my question where did you get the ratch? and itis 3/8 or 1/4 of inch drive
@treyhaberman
8 ай бұрын
My 1/4 beam torque wrench was from Amazon. The 3/8 click torque wrench was from autozone.
Пікірлер: 35