Just bought a 2000 Grizz 600 and the caliper is squeaking but after watching this I think I’ll change the brake pads too since they are weak. Easy to follow, your a good teacher! Thank you!!
@ProTechEpoxyFloors
5 жыл бұрын
Thanks, just did mine today after watching your video. Compressing piston was a big help.
@MavicAir1
5 жыл бұрын
Thanks for the very helpful video. Bought a used griz and am a bit new to it. Got the brakes done with confidence. Watching the vid made it very easy. I will be doing the bearings this winter so I've already watched that one. Any other maintenance vids you put on for griz I will watch. Helps to know exactly what tools a guy needs before starting. Thanx again.
@thomasphillips1832
Жыл бұрын
Great Video. I watched it and changed my brakes front and back on my 06 yamaha grizzly. Thanks
@flysubcompact
3 жыл бұрын
Excellent video. Thanks for the effort
@gurjitbhullar9068
7 жыл бұрын
Very helpful thanks, young man.
@alexandrbyelan6504
6 жыл бұрын
Thenks!!!!
@janko7771
6 жыл бұрын
Thanks
@rayg3074
5 жыл бұрын
good job
@landongall2080
4 жыл бұрын
Thank you
@2291225alan
4 жыл бұрын
Hi I got 2001 yamaha grizzly 600 4x4 its the brake same to this one?
@robertsullivan9501
8 жыл бұрын
great instructions, I have a 2006 Yamaha 660 grizzly and am wondering if you are going to do more on that machine, I am interested in gravity flushing front and rear brakes/rebuilding front & rear master cylinders and anything else that pertains to that model machine
@mikeduplessis708
7 жыл бұрын
robert sullivan
@eclipser2004
6 жыл бұрын
Do those allen bolts that go through the pads need any brake lube? Mine were a bit corroded and sticky. Also the pad hooks over another rod on one end and that looked a bit sticky too.
@LilasTools
4 жыл бұрын
eclipser2004 I always lube caliber pins, make sure to silicone brake lube though!
@uberleet01
4 жыл бұрын
The hex bolts are seized. Any tips?
@TheUberGopher
3 жыл бұрын
When you pop out the rear brake pin and can't find it on the floor or in the belly pan, look in the plastic air tube. That there is experience talking....
@jayonez137
4 жыл бұрын
You should really wire wheel the retainer pins and also re grease the slider pins
@dougbreakstone8780
6 жыл бұрын
I'm looking at a 2006 grizzly this weekend. Can you tell me what I should look for ands the weak spots to look at for. Thanks
@TheUberGopher
3 жыл бұрын
Front drive shaft splines. The splined shaft is short and the splines tend to wear out. I had a rear axle pop out, they are only held in by a spring pin. You can pull it all apart and bolt the two inner axles together.
@rayg3074
5 жыл бұрын
thumbs up
@broswithbows2230
7 жыл бұрын
your welcome
@EpilepsyWarning
7 жыл бұрын
my welcome?
@zionbldrs1582
4 жыл бұрын
How did you compress the rear caliper pistons?
@TheUberGopher
3 жыл бұрын
Just stick a pry bar in there.
@scottdempsey3532
3 жыл бұрын
I just did my rear brakes on a 2005 kodiak but I did it from the side not the back..why would u do them from the back?..I tried..lol..made no sence too me
Пікірлер: 27