Wow, my man, you have much to learn. You really should have replaced the seal while you were there. Please turn the shaft on that puller, hold the rest and make sure you press the pulley on flush with the end of the shaft. This belt will wear prematurely because it will not line up correctly. Please reserve that torch for when you are soldering copper pipe.
@robertcooper7467
7 ай бұрын
This is an excellent video. The camera is in a rigid fixed position, not all over the place like some I have seen. Your video walked me step by step right through this repair. I have an 06 DTS. I ended up cutting that bearing off with the Dremel tool, which you mentioned in the video. I just cut a slot the width of the blade, being very careful not to touch the shaft. Anyways, thank you, nice job.
@khanm83
2 жыл бұрын
thanks this helped a lot.. i changed the tensioner.. still making some noises.. i think my water pump giving out... thats my next task..
@raho24781
Жыл бұрын
WoW ok kool my plastic pully is locked looks like I'm gonna go down the same road Thank you for doing the Whole Video br0
@WayneLevelston
2 жыл бұрын
you was using the removal tool incorrectly, it comes off in less than a minute if you'd used a 16mm wrench and turned towards the windshield
@partsshooter
2 жыл бұрын
🤦♂️
@partsshooter
2 жыл бұрын
Bro... Troll elsewhere. Not today
@mrmagiq216
Жыл бұрын
Took me 30 seconds with a cordless impact and a 19 on the puller bolt
@JM-br9sp
2 жыл бұрын
This guy is everybody's nightmare mechanic. Haha, let's just melt th plastic pulley off! Great idea! Just when I thought the worst was over he hammers on the engine casting! Hahaha, this must be a junkyard car
@partsshooter
2 жыл бұрын
Nope... A customers car
@younis1307
Жыл бұрын
Need to order a tensioner pulley piece? Is it possible to help
@paulteusink5124
2 ай бұрын
Lube that pusher screw! And use those muscles! It's doubtful that heat was needed.
@partsshooter
2 ай бұрын
Better safe than sorry not using heat, it came off easier! I need to update that tool anyway
@thinkviral8795
2 жыл бұрын
Do you know where the output speed sensor location would be code(p0722)?
@borisp9499
Жыл бұрын
What was the mileage at the point of failure?
@partsshooter
Жыл бұрын
This car has 150k I wanna say
@cuzzcurt1
11 ай бұрын
U did that dog👍💪
@terryminor1389
2 жыл бұрын
I have a 2008 DTS that need the exact fix. What size belt do i need? excuse me for my ignorance im a computer network guy trying to fix my car
@partsshooter
2 жыл бұрын
Just a water pump belt
@terryminor1389
2 жыл бұрын
@@partsshooter thanks...ill be watching your video while i do mines tomorrow thanks again
@partsshooter
2 жыл бұрын
@@terryminor1389 cool, but the video wasn't straight through. I had issues that I didn't edit out. Hopefully yours is more cut and dry to replace
@jalsr.speak2379
2 жыл бұрын
Wow, you had trouble because you don't have enough leverage with them little open end wrenches. You didn't even use a rachet or breaker bar on the end of the pully tool. Pressed on pullies are supposed to be that tight and I'm pretty sure the pully puller tool centers itself but hey, you got her done like a cave man.
@johnperez93640
4 ай бұрын
What is this guy scared of? TURN THOSE WRENCHES the first time. Put a pipe on one of em and force that wrench to turn. If it pops the tool, oh well, but it probly wont.
@ygudream1104
Жыл бұрын
You still got the caddy?
@partsshooter
Жыл бұрын
I still service his car... runs great
@hvvzqz3677
2 ай бұрын
hey buddy you need to learn a lot I did it the same job same car in about 15 minutes work smart not hard with the right tools
@partsshooter
2 ай бұрын
@hvvzqz3677 but... you watching my video and not the other way around. Gotcha
@jamesstewart1033
2 ай бұрын
Wow, you are soooo cool. Congratulations
@alecdoyle6268
7 ай бұрын
At least I know it’s not just me.
@JM-br9sp
2 жыл бұрын
I have to stop watching
@TheDavidthegreat
Жыл бұрын
Tell nayiztazq idk what her name is to stop the promo lmaooooooooooo
@partsshooter
Жыл бұрын
Who is that???
@ajoodle5850
Жыл бұрын
Add Timestamps next time. I wasted 15 minutes watching you trying to remove them 😅
@mahmoudhasnaoui1279
7 ай бұрын
Useless effort I made a tool less stronger than yours and I managed to take the poly You don’t know what are you doing mate
@larrymiller8641
Жыл бұрын
I changed my pulley years ago with the same tool and no directions, it took me all of an hour or so to figure it out, I definitely didn't use no freakin blow torch, it was easy, crank it right off, then put the new one on in reverse and crank it right on, I don't even see why he uploaded this video like he was doing it right, dumb ass mechanic, hope u got another job besides this one
Пікірлер: 38