Can't believe it, I live in Ont. Canada and have the identical issues with my 08 Mag. Great video .
@joshuadonellan2106
3 жыл бұрын
Your start problem with the delayed start is going to be your EGR valve and down stem. Clear your down stem and maby replace your EGR valve. Also take off your throttle body and clean it on both sides . This is what I did 2 days ago I had same issues you had. Don't forget to clean out the back side of your engine block were the egr valve connect. I scraped the whole and the used a shop vac sucked alot of stuff out of the engine block .
@DiVine0719
3 жыл бұрын
I'm doing this exact same thing this weekend. Egr valve is definitely a possibility. It's only about a $70 fix with a little time for labor.
@arthurgonzales7400
9 ай бұрын
Did you also have low idle and it fixed your idle after your replaced your egr?
@stephenlawrence2228
9 ай бұрын
Dude thanks for the helpful video I’ve got the same issues… gonna check out my MAP but mainly I just wanna say your Charger is eye candy Bro she’s looking real fine
@tyjohnson2764
3 жыл бұрын
My Rpm rises past 3 at about a constant acceleration at 50mph and doesn’t come back down until it’s around 20 mph on my 07 Dodge Charger. Granted I can’t get on the highway cause the rpm will continue to boost without a decrease. Can’t seem to see what the problem is ..anything ?
@brucesmith6264
3 жыл бұрын
Have the same Issue here in 2021 ever find out what it was ?? just Curious
@dsouth423
6 жыл бұрын
Had same problem with my magnum cleaned throttle body an it fixed problem
@tennesseepipeliner3633
3 жыл бұрын
Everybody having this issue or worse...check where the EGR inserts into the back of the plenum
@1manarmyguzman629
6 жыл бұрын
Did u find the solution to the idle problem?
@reneletendre629
5 жыл бұрын
Did you find the problem with the idle issue?
@mrmoe6859
3 жыл бұрын
what makes it hesitate to start is the crank sensor and the cam sensor
@davidchartrand6213
3 жыл бұрын
So my 3.5 charger still runs after unplugging the map sensor. So I ran out and bought a new one. That did NOT fix it. With the new senor in, unplugging the map sensor still don't stop the car
@frediemac95
3 жыл бұрын
I’m glad I didn’t go buy one 🙄
@fernandocazares5925
17 күн бұрын
I've got a 2009 dodge charger. Does this have a MAF sensor or MAP sensor? Any other 2009 dodge charger owners know?
@OldTimerAutoRepair
2 жыл бұрын
not rocker arms, lash adjusters. But I would take a torque wrench to the rocker arms tho.
@markshayneholbrook2113
3 жыл бұрын
I have dang near the same issue with my 05 magnum with a 3.5 L in it Except mine vibrates real bad at low speeds in RPMs but if I give it gas real hard it straightens out and flies like a damn bird it’s the craziest thing how many able to figure it out
@dustincole6977
3 жыл бұрын
Im going threw the same thing with my 3.5l
@Smallbutsexygemini
8 ай бұрын
Having the same problem on my Dodge charger 3.5
@davidbernhisel2288
Жыл бұрын
Bro I have the same car the tick is your fuel rail making that tick put your finger on it buy the best fuel cleaner and put it in your tank and the high idle will go away you most likely have a clogged fuel injector and replace the egr valve will run like new
@uhmeizuhngralphf0549
5 жыл бұрын
You need to do idle relearn or idle adjustment with a high-end scan tool.
@geeohh8452
3 жыл бұрын
How do you do the idle relearn?
@actreasury5648
2 жыл бұрын
@@geeohh8452 turn the key to the on position but dont start it and wait for the engine like to blink and when it stops place your foot on the gas pedal all the way down turn it off and then crank
@banntasn3104
7 жыл бұрын
For your starting issues...i had a sluggish starter. It finally died at around 249k miles. The new one starts so fast it makes me believe my sluggish starter was always a problem since I bought it new in 2007.
@tennesseepipeliner3633
3 жыл бұрын
exept for them buckle/warped bumpers
@user-sw3io9dw4b
5 ай бұрын
its the egr valve tube going into the back of the intake manifold
@terriward3220
4 жыл бұрын
Was it the throttle position sensor
@jasonmeyers9413
5 жыл бұрын
Did you find the problem mine is doing this too
@markpickett9391
4 ай бұрын
My 2010 Dodge Charger also has that hesitation when starting especially when parked for awhile..a very small leak was detected after map sensor replaced and purge valve canister replaced now the throttle body assembly light has come on with the traction control light..any ideas what could be the fix?
@MRF2188
Ай бұрын
Possibly the steering angle sensor. Look up a video about it.
@derrellgibbs1022
13 сағат бұрын
I have a dodge sxt 07 it is not letting me accelerate over 40mph rn
@lederrickbrown9144
2 жыл бұрын
My rpm light doesn’t come on I need help to figure the problem is
@kevinfarmer3778
2 жыл бұрын
That’s the Crank shaft sensor that causes the hard start
@kevinfarmer3778
Жыл бұрын
That’s the Crank Shaft and Cam Shaft Sensors making the car hard start
@wrenchjr9317
3 жыл бұрын
I have this issue right after changing spark plugs white smoke would come out somewhere in the engine and it will show code P01128
@cameronarmijo4524
3 жыл бұрын
u getting any misifre code or cel?
@misskaycormier600
6 жыл бұрын
HeyHey I'm having the same bad idle issue but at times my car just shuts off while I'm still in drive ?? Help
@fabianespinoza5610
6 жыл бұрын
Faye Cormier while you are driving or while at a stop light with foot on the brake
@oscarrivera3598
6 жыл бұрын
Faye Cormier hi I have the same issue do you fix it ?
@misskaycormier600
6 жыл бұрын
Fabian Espinoza yes hard on the break
@joshreeves3593
4 жыл бұрын
With the ones that cut off randomly while driving a lot if the times it's the pcm. Stock ones are known to be trash.
@banntasn3104
7 жыл бұрын
AS for the issue I have which brought me
@heeromilov6947
5 жыл бұрын
Short runner valve mine did it to
@jamestollisonmusic
5 жыл бұрын
That's what caused the idle problem? The short runner valve?
@keithbrown4363
4 жыл бұрын
No change manner fo runner and crank senior
@ThatRacingBanana
6 жыл бұрын
So what's causing my 07 3.5 to give me a lightning bolt warning light and then it'll idle high and the gas pedal will be almost useless
@jasonpeter5140
6 жыл бұрын
Check EGR valve O ring
@DeadlyVoltsHD
6 жыл бұрын
Jason Peter second to this
@TRaySteeves
6 жыл бұрын
Aggie Charger bad throttle body or the plug to it is loose.
@jazzyjazz2599
5 жыл бұрын
@@TRaySteeves more than likely the plug
@TRaySteeves
5 жыл бұрын
@@jazzyjazz2599 yes if the locking clip is damaged on the plug it will wiggle loose and the lighting bolt on the dash will illuminate as well as a no gas pedal control.
@liudasjankauskas601
6 ай бұрын
hello sir I want to ask. How many miles do you think this 3.5 engine can drive?
@LeTuVis
2 ай бұрын
Bedos su varikliu?
@chadalexis2957
4 жыл бұрын
Try also intake sensor
@annej3387
4 жыл бұрын
I have a 2010 charger and at 4:00 makes the exact same noise when I turn my car on. Idk what it is, when you figure it out. Please comment what you found out. Also, what is the part called? (on the left of where the oil cap is at, with the hose that goes into the air filter) my air filter has oil in it. So I’m wondering if it might be that valve?
@dumbdodge
4 жыл бұрын
the rocker arm assembly stinks on these engines. mine does the same noise on my 09 dodge charger 3.5 v-6 . at oil change with Zmax oil additive it helped mine, but STP makes an additive as well, for modern engines, its very thick, however.
@josephg1855
4 жыл бұрын
Oil in the air filter means “ Blowby” Change your pcv valve. The engine is building pressure and forcing oil out into the hose. OR, The EGR is not working properly and building pressure in the engine. Either way the PCV valve and EGR will cause both of the issues of spitting oil into your air filter. Fix it quick, or you’ll destroy your engine after awhile.
@davidchartrand6213
3 жыл бұрын
Pretty sure that person who said "oil on their filter" and was asking what that part was.... is referring to the "intake manifold" and its normal for oil to be in it
@jamestollisonmusic
5 жыл бұрын
I got same idle issue how did you fix it?
@zaitoven8135
4 жыл бұрын
James Tollison did you get yours fixed
@kevinfarmer3778
Жыл бұрын
Crank shaft and Cam Shaft sensors
@elliotjones9097
2 жыл бұрын
Check your ground wires
@yesakavichasirleoin5719
3 жыл бұрын
TAKE OFF throttle control and CLEAN or replace
@jaguarsrcfamily101
6 жыл бұрын
Air intake valve needs replacing about 40$ autozone also don’t clean with any solvent if you have to clean it for temporary fix
@JaySmith-pp4ns
4 ай бұрын
Me too
@wylew
3 жыл бұрын
I got that same problem
@thomasgonzales8720
5 жыл бұрын
Did he just spray the motor LoL
@RENEHERNANDEZ1986
4 жыл бұрын
Lmao yup
@omarlemus3001
7 жыл бұрын
having same problem here..i replaced throttle body but still do the same thing...but i think the throttle body has to be relearned and calibrated with a pro scanner like the one the dealers have...
@prodigym
5 жыл бұрын
Did you solve the problem?
@queenree5
2 жыл бұрын
But how do you calibrate it witout going back to the dealers to charge you a dayum arm and leg to recalibrate it???
@craymation5130
4 ай бұрын
relearns crank and cam with 15-20 mins idling@@queenree5
@uhmeizuhngralphf0549
6 жыл бұрын
I think it's one of the O2 sensors that went bad with no code
@MrCougar214
4 жыл бұрын
That's not the problem. I have the same car, same engine, same issue. I replaced an O2 sensor that went bad, still doing it. I believe it to be either a slow starter or a dirty, possibly weak throttle body.
@eluna92640
6 жыл бұрын
Hey there in regards to the delayed start issue. My wife's 07 3.5 liter had the same issue. After allot of research we figured it out. It wasn't showing any code for it either. It turned out to be the Cranks Position Sensor. Which is located underneath the car on the passenger side of the transmission. It was defective and caused the delayed start. We also disconnected the battery during this sensor replacement. I hope that this helps you. Now we are experiencing the dipping and low idle issue that you have. A completely separate issue I think. Let me know if you solved low idle issue. Any ideas? Thanks
@Kasetownbiz
6 жыл бұрын
Ernest Luna I'm going to change the battery to see this week I will let you know
@freddyperez4154
4 жыл бұрын
Ernest Luna hello could you help with the crank shaft position location
@kevinfarmer3778
3 жыл бұрын
Freddy Perez It’s best to change the camshaft sensor and the crankshaft sensor’s at the same time, the camshaft position sensor is on the top of the engine front near the left and the camshaft sensor is under the car on the passenger side behind the rack on the transmission near the top.
@kevinfarmer3778
3 жыл бұрын
The camshaft position sensor is on the top of the engine front on driver’s side
@DiVine0719
3 жыл бұрын
The ticking is normal for these motors.
@ForexNinja
3 жыл бұрын
no they are not.... I own one My timeing belt broke shortly after it started ticking like that
@davidchartrand6213
3 жыл бұрын
Yeah It is, your timing belt breaking is just a coincidence
@bosshogg6629
2 жыл бұрын
Yo bro I swear I have the exact same problems with my 08 dodge charger 3.5l v6 and I have 210xxx miles exact same color and everything And I have codes like this : 2111 0642 2122 0335 I I changed code for misfire coil pack and spark plug and then put everything back and then car sputters when accelerating or idling I vacuum leak and I replace the tube seal and right now I can't accelerat bc throttle body or sensor and I replace my crankshaft sensor circuit bc my car take a long time before starting I thought that would make my car crank up correctly but no I was literally told it has to be relearned by scanner
@MikeySLR1990
6 жыл бұрын
Had some problem but mine happens when either I sit or while driving I got a red lightning bolt light and traction light comes on limp mode but no engine light I believe it's the trottle body sensor
@bambijones2292
5 жыл бұрын
XGEN Swiift_YT did you get it fixed?
@MikeySLR1990
5 жыл бұрын
@@bambijones2292 yes I did it was the gaskets from the EGR valve and the tube behind the engine
@bambijones2292
5 жыл бұрын
XGEN Swiift_YT thank you very much..i will get mine checked tomorrow
@exoticcancer86
5 жыл бұрын
What you mean tube behind engine
@MikeySLR1990
5 жыл бұрын
Edoria Ralston the tube behind the engine is the egr valve tube
@tiviahill592
5 жыл бұрын
You need a gf to hold that phone. 😂
@Kasetownbiz
5 жыл бұрын
Tivia Hill lol
@fdubc30
3 жыл бұрын
Head gasket soon
@user-zi4xn4fd5i
2 ай бұрын
You didn't show us where the fucking sensor is . A waste of my time
Пікірлер: 102