how do I find out if my r1 is an xc or what else ? i can't find any info , ordered the clutch kit for the 07-08 and installed the thicker pressure plates and the clutch is too stiff to the point that it doesn't disengage so i'm thinking i might have to switch plates ugh ...
@camwhyy
Жыл бұрын
Having this problem as well did you figure it out
@mac2k2020
Жыл бұрын
@@camwhyy well i had a few issues actually, the most important the bushing in the clutch lever shaft fell out and i noticed some play so i replaced that but also 2 of the clutch plate bolts guides (3 of the 6 holding the pressure plate ) were slightly bent and didn't let the plates disengage properly , it's unlikely but i would check that i was able to bend them back straight and all is good now
@ciogon
Ай бұрын
Bro,the ticker steel plate that goes first on those two steel "washer" you said that the rounded smoother face goes toward those big washers...but mine is the other way around,the flater surfaces has that worn groove...could this be my clutch problem...bike has a little drag when i come to a stop and its hard to down shift unless i come to a complete stop...if i adjust the cable the clutch then slipps in high rpm...friction plates are in spec,clutch plates also in spec...😢
@markbenyoun1476
2 жыл бұрын
Those are for the springs
@roninmantis7584
2 жыл бұрын
Automotive oil has additives that reduce friction. The clutch on your MC is a wet clutch and thus you will reduce the friction of the clutch by using automotive oil. It's also why additives to oil for most motorcycles is not a good idea. As always there are exceptions, for example Ducati is a dry clutch and is not effected by the oil. Of course their clutches are noisier and don't last as long, but it does allow more power to be transferred. :-)
@ToryII
7 жыл бұрын
use 10-30 yamalube...excellent informative video
@camwhyy
Жыл бұрын
How do you tell if you have am XC model or not? I'm having a hell of a time with my clutch and cannot get it to line up properly I have very loose clutch but if I click to gear the tire does not spin. I tried the thicker clutch plates but no luck with that either what am I doing wrong
@AlexR-fy8wd
Жыл бұрын
theres another video a guy pull the cover just a little bit so that the center rod still in place and turn the lever towards the back until you here a click the seems to fix the loose cable due to all the teeth in the center shaft not all the way in. trust me it will work i spent hours doing the same thing. here is the link kzitem.info/news/bejne/pWp_065prXdymXY
@Honcho_solo
8 жыл бұрын
Is there any way possible you can make a video showing how to properly install the clutch cover?
@Kreggsy6
8 жыл бұрын
+king irie I have since sold my bike. Don't be intimidated by the cover, people make way too big of deal about it. The important part is to make sure the small rod sticking out of the clutch basket aligns as close as possible to the hole that is in the clutch cover for the shift lever rod. Once you get them aligned somewhat, just turn the shift lever rod counter clockwise while you keep pressure on the cover, it will then grab the smaller rod sticking out of the clutch basket and suck the cover into it. You will know right away if you have it, it might take a few tries to align the two since the clutch basket rod rests at an angle. It doesn't take two people, but maybe you might find it easier if one person twists the bottom of the shift rod while you apply forward pressure. I have done it three times and have just done it by myself.
@store8294
8 жыл бұрын
+Kreggsy6 once you start twistng the bottom of the shift rod while applying forward pressure to the clutch cover, is there suppose to be any play between the clutch arm and the clutch cable? or once the clutch cover is installed is the arrow and the dot suppose to line up with some or no clutch arm play??
@TheBingo1951
2 жыл бұрын
fa legermente schifo grazie
@mjones2595
4 жыл бұрын
What if you dont mark it how do you get it right
@kirilchuk
9 жыл бұрын
nice video , now I can go and do mine. thanks man.
@miguelrg1510
4 жыл бұрын
Very good video. I didn't mark my clutch plate. How did you fix it? I mean how were able to figure out the way to put the clutch plate in right way?
Пікірлер: 17