May be a bit of a clumsy video but it's still the most clear and direct real life change on here!! Thank you for a REAL video and not a staged job..Best lighting to show it as well! I have to change out m roommate's 2009 Chrysler 300 and it will be the 2nd time! This time I won't let her fork out another $400 the shop charged last time!! I mean 4-6 bolts it's not rocket science!
@kylerchaffin5814
2 жыл бұрын
If it popped for the second time Back to back then you Have a bad water pump or thermostat
@Dmac02
4 жыл бұрын
I’m at the mechanic shop right now... they tried to say they need to take off my intake to remove the part.. I said no you don’t there is a bolt in back of the motor do I need to show you this vlog on KZitem lol!! Long story short my intake never came off. THANK YOU!
@NINO-NR
4 жыл бұрын
Please subscribe. I need subscriber
@Dmac02
4 жыл бұрын
Nino NR I do too
@johnsonmansr77justamessenger_
3 жыл бұрын
Thanks for the great walk thru steps I just able to do ours!💯
@MrSkeezyBaby
5 жыл бұрын
Hey man I’m about to change mines as we speak , I greatly appreciate this even with not one word said through the whole video you can follow this step by step lol .
@Doughboy1824
Жыл бұрын
I’m on my 8th one so fare. Thanks for the video
@Swagandkicks
5 жыл бұрын
The part is only $46 at O'Reilly's, And that was the highest one, thanks fo the video
@foxybrown9573
7 жыл бұрын
people complaining about the prices...Well darn!!! look what the mechanics havta go thru!!! You're a good mechanic
@NINO-NR
4 жыл бұрын
Thanks for the comment. Just one thing im mot a mechanic. But i do a lot of things
@mikophilo348
5 жыл бұрын
thank you so much....im here trying to figure out what parts are connected lol I took every bolt off.....even the 2 top air flow ones you kept on lol thanks a lot
@h.a.n.8855
5 жыл бұрын
I took off 4 bolths on the top the 2 side ones then make presure with a screw driver IT came out no problem then put the two side ones back then the other 4 on the top .....done; thx for encourage my vibe I did IT and save around 50dlls to 100dlls depending the mecánic thx
@michaelcoviello5567
6 жыл бұрын
PERFECT....just what i needed to see
@VRRider
7 жыл бұрын
One thing to keep in mind make sure your upper radiator hose is not touching your idler pully. Have at least 3/16" clearance. I just repaired one because of the original owner who did the work himself and admitted he was not a mechanic did not see this problem while repairing it.
@Kingjuice2
Жыл бұрын
How do I clear the radiator hose from the pulley because it’s rubbing now
@abrahizzzle
7 жыл бұрын
Bout to replace it on my dad's car. Antifreeze puddled up in every nook and cranny. Big mess. Rockauto had the cheapest prices, $28 shipped to me, but need it asap. Oreilly for $45. Looks easy
@kingbrod1
6 жыл бұрын
lol,he didnt even check the o-ring around the pipe before installing the new outlet. it may be flattened out and dry from heat,which will down the road leak when it finally goes. inspect it to make sure the ring still has its round shape,not flattened. and clean the base where the new outlet mounts to engine of debris build-up,the seals have to make good contact. maybe he did,during the filming stop. also it would have been nice to follow thru the whole process of filling the system up with coolant,because you have to breed the system right there at those bleeder valves. unbeknowest to the novice at home diy'er,if you fill up the system without doing that step,you'd be filling it up with air pockets,and the coolant won't circulate as it should,and you will end up having a problem such as.......you guessed it...OVER HEATING!! he did the best he knew i guess. anyways,if ya gonna make a video of a process,show the whole process,correctly.
@NINO-NR
6 жыл бұрын
kingbrod1 Until now everything work perfectly.. Thanks 4 the comments
@kingbrod1
6 жыл бұрын
Nino NR Good deal. Keep up the good work bro. Without KZitem a lot of folks would be either tearing stuff up,making it worst or spending lots of money at the dealer for something they could did at home for hundreds less. 😂
@philn4013
4 жыл бұрын
Just did this bruh glad I scrolled down to check out your comment
@Copper_2020
3 жыл бұрын
Good vid
@tracyjones775
7 жыл бұрын
ok man thanks for that again
@VegaH_
Жыл бұрын
I took mine apart but now the holes don’t line up 😂
@tercerorosemary
5 жыл бұрын
8:06 scared the shit outta me. Had it conected to bluetooth in my car.
@leandrosantos789
4 жыл бұрын
Lol
@dakotadavis769
7 жыл бұрын
I just replaced this part today didn't run yet should I open top and wait to see some coolant come out the top before tighting top post one or its good to go
@dakotadavis769
7 жыл бұрын
by the way great video help me change mine
@NINO-NR
7 жыл бұрын
tighten and its good to go
@nabal714
5 жыл бұрын
Did u tighten the skrew from the middle because it squirts water up
@dlow4261
3 жыл бұрын
So I’m confused because my 2009 charger is leaking and this part needs to be replaced. One mechanic was charging $800 because they said the whole part from the top to be removed and it was a lot of work So I took it to midas, they are quoting 170 to replace it But it seems like it’s a simple replacement that I can do… keep in mind I have absolutely no mechanic experience 😂.. any input greatly appreciated it
@TommyJacksonVlogs
5 жыл бұрын
Ok I took mine off but that pipe went back to its original position inside the engine how do you suggest I get it out
@KAYSWIPA
7 жыл бұрын
was your check engine light on
@NINO-NR
7 жыл бұрын
no. it broke while i was running the car
@rubenbustos8193
Жыл бұрын
What was the point of removing the hose? I didnt have problems taking it out with the hose on...
@gabrielav5334
6 жыл бұрын
im going to do this to my dodge charger as well. Do i need to drain the coolant before doing this?
@MrMONEYMAN773
3 жыл бұрын
Can you change the part w/o it your 2.7 overheating just wanted to change it out period
@BOUNTIFUL65.11
6 жыл бұрын
I didn't put that wrench as a wedge and pushed the pipe closer in the motor..what do I do to get it back in line?
@ducks1089
6 жыл бұрын
Thanks for the vid it helped but now I have a problem, I have water bubbles leaking from the top of the valve what did I do wrong ?
@NINO-NR
6 жыл бұрын
tight well that thing. otherwise is broken u need to replace it
@tracihale7092
6 жыл бұрын
Does this cause your car to run hot when it's bad
@NINO-NR
6 жыл бұрын
Traci Hale yes
@tempakilla
3 жыл бұрын
This would be the second time from about 2 years ago that this has happened. It busted open in the exact same spot as yours. Twice!
@q.aarreadams652
3 жыл бұрын
You should get an aluminum one for only 10 dollars more
@NINO-NR
7 жыл бұрын
I didn't do it. Just be careful not to drop any antifreeze if by any case u drop the antifreeze. after installing just fill it up again to the required level. But it's up to you if you want to do it
@MadSharkbite
6 жыл бұрын
Saved my ass
@MexAttacks
7 жыл бұрын
dealer quote to do that 367 dollars.+89 dealer part. my mechanic 85 dollars. what's your opinion on that? did you use a dealer part or aftermarket?
@MexAttacks
7 жыл бұрын
so ended up going to my mechanic. he charged me $150dollars to replace the entire piece with metal hose attachment ... took him less than 2hrs. he raised the motor up and problem solved.
@VRRider
7 жыл бұрын
Dealers are not intended for out of warranty repairs. They are for warranty repairs only. If your vehicle is out of warranty do not take it to a dealer unless you have money to burn. Dealers have to charge the same rate they do for warranty service as they do general public other wise it would be like insurance fraud only its warranty fraud if they charge out of warranty repairs less they they charge warranty repairs.
@tempakilla
3 жыл бұрын
Yeah if you do it yourself you save 100 bucks
@KingllTank
5 жыл бұрын
He forgot the last step. To bleed it. If you do not bleed the air out of the system, your check engine light will come and read coolant system malfunction.
@shaqlindsey8
4 жыл бұрын
Titus Lawrence How do you bleed it?
@freddiesalinas6679
4 жыл бұрын
I’m changing mine but the bolt whole don’t match up
@tracyjones775
7 жыл бұрын
will that mess up your car time it starts?
@NINO-NR
7 жыл бұрын
yes..
@tracyjones775
7 жыл бұрын
ok imma buy this part tomorrow and put it on. and I should be good
@q.aarreadams652
3 жыл бұрын
Should use aluminum. The plastics ones always end up getting busted. The aluminum one is only 5-10 dollars more. Way better.
@FreddieRougar
6 жыл бұрын
does the valve part come open? or is it supposed to be closed
@NINO-NR
6 жыл бұрын
Freddie Rougar the valve has to be closed
@robertjackson19965
4 жыл бұрын
Do I need to bleed the system after changing this part ?
@nb6584
4 жыл бұрын
Yes.
@franciscotecpilemontalvo6681
6 жыл бұрын
Una pregunta como podré cambiar el tubo en mi dodge charger está quebrado
@TCG_Jay
5 жыл бұрын
How much did the part cost you
@xjeffrox
6 жыл бұрын
Yo... what do i do if the pipe that run towards the back gets stuck? I tried fixing mine but didnt realize the pipe moves back and forth now its just stuck and im not able to move it far enough to remove the part
@TommyJacksonVlogs
5 жыл бұрын
Jeffrey Garrido same🤦🏽♂️
@DTQTamkclf46
3 жыл бұрын
Why did this person think they could unscrew that thermostat housing with a socket screwdriver by hand?
@williamyoung5353
3 жыл бұрын
Come on yall leave butter fingers alone lol
@tracyjones775
7 жыл бұрын
mine start leaking out of the top on the stem
@NINO-NR
7 жыл бұрын
mine started like that but busted while running the car its best to change it know
@Luid5833
6 жыл бұрын
Whats the part name
@alexisangelcoronado2936
6 жыл бұрын
What about that valve on the middle ? That should be open or closed can somebody tell me
@NINO-NR
6 жыл бұрын
Alexis Angel Coronado closed
@josea953
5 жыл бұрын
That's why it's overheating there's a big hole in it.
@tracyjones775
7 жыл бұрын
what does this do? I have to change the same thing on my car soon.
@sturgeonhunter2321
6 жыл бұрын
Tracy Jones it's a bleeder valve
@karennoscar
7 жыл бұрын
how much $ does part cost
@NINO-NR
7 жыл бұрын
38.99+tax
@howardj.cuarezma4542
4 жыл бұрын
This keeps happening to my charger what else can be wrong?
@NINO-NR
4 жыл бұрын
Where did you buy the parts? Sometimes the parts are defective. That happened to me the first time. Then I bought the part in auto parts and 3 years have passed to change it and everything is fine. subscribe to my channel please.
@walkingrazor863
4 жыл бұрын
Just ordered Dorman part #902-301HP from Autozone...I think 🤔 it’s made out of aluminum...gonna test it to see if it can last past 5 years, mines has started leaking. The one I currently have installed was a brand from O’reilly’s which did ok and lasted about 5 years down here in Florida...
@antonioelguea6904
Жыл бұрын
Bro the fucken tube dosent want to pull back
@NINO-NR
Жыл бұрын
Behind the motor there is a clamp that holds the tube, remove it from the tube.
@sircharles9718
7 жыл бұрын
nice try
@cesarperez-ii8vc
7 жыл бұрын
@ 2:51 lol the dumbass is just pulling on the pipe n it still had some bolts on it lmao i wouldnt want him as my mechanic 😂😂
@NINO-NR
6 жыл бұрын
Do u see it well?
@antjohnson3724
6 жыл бұрын
This shit is hard to do on a 2007 Charger!!! Something isn't right
@ArielPerez-n1h
Ай бұрын
Recuerda gue ahí gue untarle en los bondillo pegamento o cilicon gue vender para eso resistente a las altas temperaturas saludos
Пікірлер: 89