Thank you this helps so much. If you doing this Get you a flexible extension and any cheap electric wrench to make this 2-3 hours if not days project to a 30 mn project and save yourself a lot of hassle. One more thing if you just changing the thermostat you don’t need the pipe out cause it’s near impossible to do so you can easily tilt the pipe once you got the 2 10 mm that’s on the thermostat housing off that secure the bigger pipe and change the thermostat from the side without pulling the pipe out.
@dasher4117
3 ай бұрын
It’s relatively easy to pry that pipe out with a small-ish screwdriver. Just gotta be careful not to pry too hard haha
@lizmontero536
2 жыл бұрын
I’ve been looking for videos and the closest I got to finding where it was at was from a video where a guy had more background music than actual info 😂 Thank you so much!
@wjdiv1
2 жыл бұрын
No problem thank you for watching
@Breaking_Beard
2 жыл бұрын
I know the exact video you're talking about 😂
@katiebourgeois6181
10 ай бұрын
Say bro thank you for your help. Finally found a video that doesn't try to over explain everything and confusing the hell out of you. You are the man!
@wjdiv1
10 ай бұрын
Thx🫡
@rickvargas9717
2 жыл бұрын
Thnx for the info, you're about the only one that explained this the right way. Thnx!
@wjdiv1
2 жыл бұрын
No problem ,thank you 💯👍
@jeffreymills3950
3 жыл бұрын
Omg I work on cars to especially on my 2011 camaro which is my project car. But I couldn’t find for the longest time the right video with all the info on it. You did great I love it . Thanks you helped a lot!!!!
@wjdiv1
3 жыл бұрын
Appreciate that 💪💪💯💯
@shuntawolf
2 жыл бұрын
Short and sweet and simply stupid to the point.... Nice!!!! Better than some I've seen tonight for sure!!!! I LIKE the "move the foam out the way and there it is"!!!! Now to figure out if I can get to it all without pulling the intake, but if it's only a few bolts then may just do it anyway... Not my car but a customers ... Good job!
@wjdiv1
2 жыл бұрын
Appreciate that simple is best
@kewlbud8868
3 жыл бұрын
Thanks brother! I was just about to start taring into my wife's friend's Camaro just for the therm! This video helped a TON!
@wjdiv1
3 жыл бұрын
Glad I could help appreciate you watching
@kewlbud8868
3 жыл бұрын
@@wjdiv1 A little side note if you ever remake this video for some reason I had a hellof a time getting the metal pipe broke loose from the thermostat housing, but putting the bolts back in to hold the housing in place, you're able to wiggle the pipe up and down and easily break the seal the o-ring creates and than the pipe slides out of the housing like butter!
@wjdiv1
3 жыл бұрын
@@kewlbud8868 appreciate the addition thanks 👍👍
@angelabarca670
8 ай бұрын
Thanks for the help at the 1:30 mark. You showed those gaskets, were you abke to find the and know what they are called.mine is leaking from the bottom
@Joshvn
5 ай бұрын
Hey do you have a name for those gaskets or part number by chance for the o ring gasket?
@dasher4117
3 ай бұрын
Good vid bro, this car ain’t too hard to work on. That thermostat is terrible compared to most cars tho lol
@joegray1155
3 жыл бұрын
Big help my friend. I was just tracking down this very thing and this showed me everything
@wjdiv1
3 жыл бұрын
Glad I could help thanks for watching 👍👍
@tarellpeterson8101
4 ай бұрын
Good work bro
@Domovsdono
2 жыл бұрын
Greatest thermostat video easily
@wjdiv1
2 жыл бұрын
Thanks
@javeusramsey9289
6 ай бұрын
Thank you brother!!! Very insightful!!!
@wjdiv1
6 ай бұрын
Thank u 💯
@robertsarabia2828
Жыл бұрын
Thanks! I was able to fix mine using this video.
@wjdiv1
Жыл бұрын
No problem thank you for watching 💪💯
@HaloGTMaster94
9 ай бұрын
Amazing!!!!!!
@nunyabidness4320
2 жыл бұрын
Thanks for the help. Just what I needed. 👍🏽
@sergiogonzalez8639
3 жыл бұрын
Exelente ayuda tengo que ver un motor de un amigo que tiene problema de temperatura , filmaste el ardado del motor? Gracias desde chile
@charlesbrown7389
3 жыл бұрын
My man... you just saved my lil sis
@wjdiv1
3 жыл бұрын
Glad I could👍👍💯
@derishaturner83
6 ай бұрын
Thanks I found it! Whew. I have no time to be paying $350. Btw please show me how you get to the temperature sensor 😢
@rschellhase9164
2 ай бұрын
Thank you 👍
@freesamples8360
2 жыл бұрын
My man much appreciated!
@wjdiv1
2 жыл бұрын
Appreciate u fam💯
@tomrobards7753
Жыл бұрын
Yo bro the pàssenger side of the vehicle is the right side always ! ! When getting parts if you told the parts guy the left side you would get t wrong part
@JohnSmith-lf8kg
2 жыл бұрын
How did you remove the second bolt in the back that holds the metal pipe? I'm having a hard time removing it. Its stuck on as hell and won't move.
@wjdiv1
2 жыл бұрын
I don't know if yours has been removed before and is crossed but try leave top bolt in to give yourself more leverage
@malcolmalvarez5740
3 жыл бұрын
Thanks brother great video
@wjdiv1
3 жыл бұрын
No problem thanks for watching 💪💯
@kvngspectra7517
2 жыл бұрын
How did you lock the thermostat into his housing. With the strength of the spring I don’t know how to get it positioned in
@toody9349
2 жыл бұрын
I trying to see myself
@kvngspectra7517
2 жыл бұрын
@@toody9349 so look if you buy a thermostat from autozone it’s doesn’t come with anything but if you get one from oreillys it’s comes with this really hard cardboard in the shape of a circle and you can use that to push down on it
@nutmagnet1874
Жыл бұрын
Love when you say "Get to wrenchin'" Peace
@wjdiv1
Жыл бұрын
💯💪
@onemanbodyshop
3 жыл бұрын
Great info fam you do it all🔥🔥🔥💯💯💯
@wjdiv1
3 жыл бұрын
Thanks fam, i appreciate u 💪💯💯
@michaelgladney9657
2 жыл бұрын
Man thank you. I was lookin for 2 days for this shit
@wjdiv1
2 жыл бұрын
No problem
@LUISMENDOZAist
2 жыл бұрын
Great info bro thanks 🙏🏾
@wjdiv1
2 жыл бұрын
Thanks fam
@brycengarber8745
2 жыл бұрын
Thanks for the video
@wjdiv1
2 жыл бұрын
💪💯
@terrranhughes6643
18 күн бұрын
Bro how did u get the new thermostat in
@dagorilla5177
2 жыл бұрын
Let em’ know dawg!!!! I sent this to my chick dad! Preciate yu!
@wjdiv1
2 жыл бұрын
Thanks fam 🙏
@BLACKRAIN390
3 жыл бұрын
Sp💦t that game fam 🤜🤛
@wjdiv1
3 жыл бұрын
Appreciate u BLACK RAIN 💪💪💯
@pilotnamealreadytaken6035
11 ай бұрын
Thanks!
@wjdiv1
6 ай бұрын
Thank u 💯
@stephenlumpkin6629
Жыл бұрын
I am stuck at the pipe. One bolt or two? I can't even feel around it there
@amieperkins5770
3 жыл бұрын
Thanks for info
@wjdiv1
3 жыл бұрын
Thanks for watching 👍💯
@IamYoutubecertified
3 жыл бұрын
I replaced the thermostat on the camaro and now I have a leak in the rear. I believe it's coming from the thermostat housing. When I assembled it the first time I jist replaced the gaskets (it leaked) I took it apart and re assembled it but this this time I used the gray gasket maker and it still leaking back there. Any ideas on what i should look?
@wjdiv1
3 жыл бұрын
I took my thermostat housing off the pipe to replace my thermostat but first I removed the two bracket bolts for the metal radiator hose to give me room for alignment I don't know if u did or didn't just throwing ideas. Did u lock thermostat into housing? Is there any chance something could be misaligned the gasket should be adequate without sealing. Are u sure ur leaking in the back?
@gregwilcox1696
3 жыл бұрын
where and what is the water outlet? they said my water outlet seal is leaking and 3 pipes in the rear of the motor. Thanks
@wjdiv1
3 жыл бұрын
I believe the pipe ur speaking about is in the front with the two gaskets on it. In the video its around the 2 min mark. In regard to the three pipes in the back I only saw the one with the thermostat attached. Hope it helps.
@kustominstinct
3 жыл бұрын
Get it in bro let them know wuzup 👍
@wjdiv1
3 жыл бұрын
Trying fam appreciate u💪💪💯💯
@alek0585
5 ай бұрын
Is it LGX engine?
@toody9349
2 жыл бұрын
How do u compress the thermostat to take out and put it back in
@thomasgrant91
Жыл бұрын
Nice
@kabrenkearse4907
2 жыл бұрын
Good a** info bru
@wjdiv1
2 жыл бұрын
Appreciate that 💯
@djcezah
Жыл бұрын
Bruh the foam was the best angle
@Ligasunday
3 жыл бұрын
Was there any torque specifications u had to follow
@wjdiv1
3 жыл бұрын
Tight enough not to leak yet not tight enough to break 😁😁😁 nah jk I don't know the exact number will be a little difficult to use in certain areas tho, u might find proper specs online
@allaccessja7097
2 жыл бұрын
Where are you located?
@coreystone6000
3 жыл бұрын
Thanks Bro because all the examples it’s shown in the front and it’s not…Thanks
@wjdiv1
3 жыл бұрын
No problem fam
@andrescamargo3440
Жыл бұрын
Any part numbers you could share please?
@michaelgladney9657
2 жыл бұрын
Yooo I need your help. I hit a tree stump which put messed my radiator up. The car kept running hot and I kept putting water in it to cool down. So I ended up replacing my radiator. It’s not leaking water anymore but it continues to run hot after 3 min of driving. Is it the thermostat or what is it?
@wjdiv1
2 жыл бұрын
Check the little black expansion tank bolted to frame on the passenger side, they tend to fail if the car over heats
@wjdiv1
2 жыл бұрын
Also check fluid level and with that try to burp system of air bubbles hope that helps you
@michaelgladney9657
2 жыл бұрын
@@wjdiv1 how do you burp the air bubbles and what expansion tank lol . Please get back with me
@wjdiv1
2 жыл бұрын
@@michaelgladney9657 easiest way to get air out is to slightly raise front of car when refilling squeezing radiator hoses to help dislodge air from inside coolant system. There is a black expansion tank or reservoir bolted behind the passenger wheel behind wheel well cover that will cause car to overheat due to a plastic tab breaking loose allowing it to leak
@michaelgladney9657
2 жыл бұрын
@@wjdiv1 thank you, last question the ac condenser thing attach to the radiator is kind of bent at the bottom. Is that a problem?
@blakeearnheart1313
3 жыл бұрын
I'm trying to replace my thermostat on a 2010 v6 camaro and I am struggling to get the pipe that leads into the thermostat and thermostat housing any suggestions?
@wjdiv1
3 жыл бұрын
The pipe is bolted to the housing, u may have to put the housing back in the original position to loosen that connecting bolt then remove pipe and housing
@jezzyjean1880
3 жыл бұрын
if you just changing the thermostat you don’t need the pipe out cause it’s near impossible to do so you can easily tilt the pipe for the thermostat to face up once you got the 2 10 mm that’s on the thermostat housing off and a 15mn a 13mn that secure the pipe and change the thermostat from the side without pulling the pipe out.
@oscarescandon9204
2 жыл бұрын
I can’t get mine to pop out any suggestions
@wjdiv1
2 жыл бұрын
A little more muscle 💪probably a little corroded
@oscarescandon9204
2 жыл бұрын
@@wjdiv1 man I can’t get it to come out for some reason lol it’s pissing me off lol do you know how many screws their is on the thermostat itself
@wjdiv1
2 жыл бұрын
@@oscarescandon9204 2 screws connect thermostat housing to pipe
@wjdiv1
2 жыл бұрын
@@oscarescandon9204 try twisting housing away from pipe
@oscarescandon9204
2 жыл бұрын
I got it off bro but still over heating not sure why
@mechanicallyinclinedr.keet488
2 жыл бұрын
👍
@wjdiv1
2 жыл бұрын
💪💯
@infernolt7622
2 жыл бұрын
What a pain. I dred the day mine goes bad.
@stephenlumpkin6629
Жыл бұрын
you have no idea
@alexmacias1515
2 жыл бұрын
This job is for 10 years old child
@wjdiv1
2 жыл бұрын
Everyone is at different stages of life and skill always remember what's easy for you may not be for others I'm sure u dont know everything unless you do?? Appreciate the comment
@kvngspectra7517
2 жыл бұрын
@@wjdiv1 lol bro I’ve changed so much on my car and this was literally one of the most annoying
@wjdiv1
2 жыл бұрын
@@kvngspectra7517 true🤣🤣
@kvngspectra7517
2 жыл бұрын
@@wjdiv1 bro please tell me how you locked the thermostat into it’s housing because I can’t do it. The spring is too strong. I’ve see. People take it apart and place it in a certain way. Is that the correct method?
@wjdiv1
2 жыл бұрын
@@kvngspectra7517 I didn't do anything special to install. Is everything seated properly? Because it is easy for things to get misaligned back there
Пікірлер: 120