Thank You for such a Brilliant instructional video,I found this educational,Once again Thankyou
@cacolondon
10 ай бұрын
Perfect thanks so much to share. Lucas Silva from Portugal
@michaelgarnett218
3 ай бұрын
Great video and very well explained, but at the end you mentioned about having to have the correct software for reprograming the actuators if you change the hydraulic fluid. The software and hardware needed is lexia 3 and Diagbox and it also has to be used after fitting a new clutch for realignment of the clutch and bitting point, Did you do that as not mentioned at all in the video ?? otherwise this video is very well explaind keep up the good work. Thanks
@AlexCaraYman
10 ай бұрын
Hi, i have changed the clutch kit on a egs 508 (valeo) the car is running fine now but sometimes is making a clunk, clunk noise when I switch from N to A, or when shifting from first to second gear and second to first gear. Actiator fluid have been changed with Ravenol Actuator fluid
@arbenbytyqi9732
6 ай бұрын
Add Gear oil treatment 207 mg (ceramic once it's better) and you with hear nothing ....take out 200mg transmission oil in order to add Gear treatment and it's with make no noise after that at all .....use breather for adding and removing under battery and housing
@AlexCaraYman
6 ай бұрын
@@arbenbytyqi9732 I can't find any ceramic gearbox oil treatment, only ceramic treatment for engine oil
@donner101
3 күн бұрын
How many hours labour is this for a pro mechanic?
@Robde84
Жыл бұрын
Great video. Did you fit a replacement dual mass flywheel like original? Or upgrade it to the single piece flywheel. I see there are two types when looking on the parts websites and it says they can be converted. I am just making a plan for my 100k c4 cactus in the future as I have started towing a trailer... Sometimes I can smell it if Im too vigorous 😂😂, or if she's driving 😂. I have the diagbox software.
@crankyconrods7417
Жыл бұрын
All oe duel mass ect iv seen people struggle with resetting clutch bit points or have issues with bit point on solid mass flywheels these can be real temperamental
@wildfruits477
5 ай бұрын
I’ve got a c4 grand Picasso the actuator is getting empty and oil is dripping by the gearbox, would this be the slave cylinder? Does the actuator oil go threw to slave cylinder?
@crankyconrods7417
5 ай бұрын
Yes actuator fluid does go through the slave
@jambacardi2474
Жыл бұрын
Great video, have a C4 with 116k on it , sometimes pulls away fine and other times it judders ,if you floor it it wont judder, Its been like this for 2 years. thinking of a clutch reset ? but unsure this will help .gearbox oil was change about a year ago with MOTUL MOTYLGEAR 75W-80 with no apparent change. Any thoughts
@crankyconrods7417
Жыл бұрын
Clutch getting weak I have a c3 does the same thing
@sergiikopchonov7137
4 ай бұрын
Hello. Be kind, tell me please. What to do in such a situation. On a Peugeot 3008, the robot changes gears normally at 1900 or 2100, but then after these numbers it makes 3000 revolutions and shifts the throttle. It’s as if there’s a lost connection somewhere. There are also foams at low speed from 5km to 10km. she sometimes twitches.
@b3nniy
Жыл бұрын
Hi, its possible to convert it to a manual gearbox, how difficult its to do it and is it worth it? Kind regards
@crankyconrods7417
Жыл бұрын
Hello and welcome I have thought about that myself I might have to give it a try some time
@b3nniy
Жыл бұрын
@@crankyconrods7417 i have a customer who's got the Peugeot 508 with egs gearbox, i follow all the instructions from Mad4frenchcar channel, (thats the way i discover you 😃) and still not working. Now the customer its worried about spending more money. I told him we should find a donor car and convert it to a manual. Now i am not sure , its the ECU needs to be reprogrammed for a manual gearbox or have nothing to do in order to start the engine. Kind regards.
@crankyconrods7417
Жыл бұрын
Email me at crankyconrods@gmail.com cars lab and we can discuss further what's up with the 508
@perhell8405
Жыл бұрын
Is it not a selfadjusting clutch that needs to be mounted with tool to take the pressure off pressure plate ?
@crankyconrods7417
Жыл бұрын
It's just a normal clutch and flywheel
@robertocp487
2 ай бұрын
Buenos días. Me puedes decir la referencia del Kit Valeo??? Muchas gracias.
@monkynuts1261
9 ай бұрын
Hi do you know the torque settings for duel mass flywheel 1.6 hdi semi automatic 109 h
@drewlingard4483
Жыл бұрын
Thanks matie, how do you know when there is enough oil in it?
@crankyconrods7417
Жыл бұрын
Oil level is on the bottle resivoure with a min and max ✌️
@monkynuts1261
10 ай бұрын
What are the duelmass torque settings,they say 2.5 Dan 0.8 Dan then 30m dan ,then 90 °.I don't understand Dan ,I understand nm
@crankyconrods7417
10 ай бұрын
Depending on what engine you have the dv6 hdi 1.6 is 110nm to 115nm flywheel a around 30nm for clutch plate. But it's best to find out what engine you have as there a little different
@nathanhuitson1418
Жыл бұрын
could it just be a sensor, I don’t have any engine management lights on
@Joole1000
Жыл бұрын
King
@laxonetrc
Жыл бұрын
Great video
@lovepreetsinghhanjra1997
Жыл бұрын
👍🏻👍🏻
@nathanhuitson1418
Жыл бұрын
Good evening, I’m hoping you can help, I have the same car that I have just purchase, and I drive it in automatic, when pulling away it judders
@crankyconrods7417
Жыл бұрын
Hello and welcome I take it your car is around the 100k miles range
@nathanhuitson1418
Жыл бұрын
@@crankyconrods7417 yes mate, 131k full Citroen service history, I have only just passed my test in an auto, got the car not bad condition etc, but when I pull away it judders, hoping it’s nothing to serious
@crankyconrods7417
Жыл бұрын
Sadly it sounds like the clutch is starting to get to the end of its life you could try doing a recalibration on clutch point but I don't think it will help you. I have a c3 1.4 auto but a 5 speed gearbox and that lurches and judders on take off that's 115k miles. When you get a chance put it in manual mode in 4th or 5th in low rpm and floor it if the the rev counter climbs fast but the speed does not you could have a slipping clutch which means it wount have long till it fails if your a little hard on it✌️ hope this makes sense
@nathanhuitson1418
Жыл бұрын
@@crankyconrods7417 thanks for getting back to me, yes makes sense, I’m going to get my mechanic to plug it into his computer tomorrow, is it easy enough to reset? it doesn’t always judder though, if I give it a certain amount of revs it’s fine, it does through all the other gears fine, is it easy enough to use the manual gears? I don’t even know if they work
@crankyconrods7417
Жыл бұрын
Your mechanic would know what to do. But if its behaving other than the odd juddering then I'd leave it alone till it gets worse ✌️ but never hurts to get a second opinion
@Rosisportbuilds
4 ай бұрын
Please I desperately need help!
@Rosisportbuilds
4 ай бұрын
The clutch slave just empties into the box and I can thing why 😭
@chrisdowns3725
Жыл бұрын
How much do you charge for this??
@crankyconrods7417
Жыл бұрын
Send me an email crankyconrods@gmail.com thank you
@jagdeeprandhawa1873
Жыл бұрын
Stop waffling
@DarkFireLightFire
Жыл бұрын
Clown. You make a video please explaining how to replace a EGS clutch on a citroen 🙄🙄
Пікірлер: 50