First video I found that mentioned parking in neutral. That saved me a lot of time and money. Thanks.
@HenryJMuckenfuss
2 жыл бұрын
Thanks for the video. It seems very helpful. I'm going to go through these steps. For the most part, my 2011 has been very reliable. I've replaced the TPIM, Key Switch, and battery in the last three years. At first, if I put it in park after not starting, it would start, but that doesn't work now, which is why I'm leaning towards that safety switch built-in.
@darwinismyneighbor
Жыл бұрын
Simple, to the point, no BS. Thanks, good video
@NK-gz4mi
Жыл бұрын
Thanks for showing that trick to jump relay. Easily found out my starter was bad 30 mins later all fixed.
@sankofaimani2899
Ай бұрын
Great video information 👏🏻
@aarnold47
10 ай бұрын
I have a 2012 ram and I can go weeks with it starting and then it won’t. Then it will start again. Love your videos
@DreReel
2 ай бұрын
Did you ever figure anything out? Mines will start but when I cut it off for like 5-10 min it won’t start back but after like 15min it will
@alexagha-khan4538
2 жыл бұрын
very nice, very informative and really a well done video!
@marklindenmuth9584
Жыл бұрын
Super great video!
@forhisgloryministries
2 жыл бұрын
Awesome tip thanks for the help
@justincortez6868
2 жыл бұрын
The 40A fuse was the problem. Thank you sooooo much!!!
@dalebryce3511
2 жыл бұрын
I'm having the same problem. Did you figure out what was going on? I changed everything for my fuel. Pump and injectors also thought it was loosing prime but now I'm lost. It does the same crank no start 2 or 3 times after it sits for 4 or more hours
@justincortez74
2 жыл бұрын
@@dalebryce3511 yes, the 40A fuse was the problem as depicted in the video. The reason my 40A fuse blew was because my ground wire that connects to the starter (yellow wire) it got spliced opened somehow someway and everytime the copper wire touched the frame of the truck it blew that fuse. I noticed it because the wire was stuck to the frame, all i did was replace the fuse and then put electrical tape around the wire so the copper wires werent showing no more and if it did touch the frame it wouldnt blow the fuse anymore. Have you tried to see if the fuse is blown?
@dalebryce3511
2 жыл бұрын
@@justincortez74 I havent checked it. But would it start after a few tries and then run ok the rest of day. Then the same no start for a couple tries the next morning?
@dalebryce3511
2 жыл бұрын
@@justincortez74 thank you for replying. I'm so lost at this point
@justincortez74
2 жыл бұрын
@@dalebryce3511 at first it did, then it wouldnt start at all. Thats when the fuse got blown. Whats year make and model of your truck?
@nobody3923
Жыл бұрын
Awesome vid, thanks 👍🏻
@leemossman1
Жыл бұрын
Awesome! I'll try and bypass the relay.
@robertkleczka1308
9 ай бұрын
Thanks for your information.
@bevanzenti
11 ай бұрын
Great video. I have a 2004 which is currently problematic. It will only RUN after battery has been disconnected and reconnected. After this, it will will fire, but cuts fuel immediately.
@marthasmith3227
2 жыл бұрын
very helpful do you have any tips about a 2011 doge ram truck that the battery goes dead after being parked now even with giving cables the truck wont start it just clicks. Everything turns on when cables are connected and I was told by mechanic that the battery was good (it is brand new) told me I had a shortage somewhere? Any tips if I should follow these steps again trucks battery is dead at this time....also i started having issues with starting no issues with powering on but it would not wont to start acouple of time than it would start and I was fine throughout the day but once I park vehicle in the morning power is gone also where do you get those pins to check the fuse?
@Yeakerr
6 ай бұрын
Oh and thanks for video i think i will be able to fix this truck eventually.I jumped across the two spots you showed and all i got was a little spark and nothing from starter so i asume i have bad starter?
@paradoxdea
2 жыл бұрын
Thank you sir!!
@kenmartin7175
Жыл бұрын
Hi I’m wanting to hook up a led strip on my ram. Which fuse should I use that will allow the strip to turn on with remote start?
@vibuy9231
Жыл бұрын
How do you start the vehicle when you put those wires in
@blackopal3138
Жыл бұрын
Oof! lol, I was hanging on your every word, then you went into your outro, and my heart sunk, lol... this is right where I am at, but it turns over just fine, it won't start though.... I have fixed two wires, oddly enough, the same wire in 2 places, at the TIPM and at the PCM, I believe it's the ASD wire. green/orange tracer. ... I'm searching, because I really feel like it's just some real simple programming glitch I created with scores of boosts, attempted resets, battery disconnects, cz I fixed those wires, put new batt, starter works, I've messed around in the WIN also, but acc and ON run properly, and FOB buttons all work everything. OH!! Also, I believe this because through all of this(4 yrs of hell) security light has always flashed as normal, along with the whole start up routine in the truck, but now the security light doesn't come on and the hood signals open when it's not, so It's like I changed something for the first time, but still no luck.... aarrgghhh! lol peace, ty
@LehewTech
Жыл бұрын
When the engine is cranking do you have spark, fuel pressure, injector signals? Can a scan tool read RPM while the engine is cranking and if so is the RPM above zero while cranking? Do you have another key you can try to start it with? Are there any stored error codes in the pcm or any other modules?
@blackopal3138
Жыл бұрын
@@LehewTech Wow, ty, and , once again... oof, lol... ok, I have an OBD reader, no scan tool, I use InCarDoc Pro.... I can try and place a mirror to watch RPM?, lol, or I can just stick it in and rund look at tach? .... Yes, I was getting an evap code 0452... but I still had a jack on the passenger side, now it's down, Idk if the code is still there, and a low voltage code 0562... sorry I'm reading the report and typing, it says evap emission system pressure sensor/switch low, so ya, I just assumed those were from the battery dropping... I'm going right now to put the charged battery back in, a lot of stuff I've tried, I was hooked up to another running car..... One time about 3 years ago, I did the 3 taps with the positive cable on the positive post, and it seemed liked that was the only successful reset I've accomplished,it did a big click to dead and back on, big as in loud and obvious, then fired back up with everything whistling, and spinning, and then worked for a long while. I was so happy, but it has never worked again....
@blackopal3138
Жыл бұрын
@@LehewTech Forgot, I have been using two keys interchangably, not systematically with each one. That reminds me, I also wanted to say, you have to keep in mind my systematic checks are subject, even likely, to be incomplete somehow. i.e. try X with key on, then key off, then try Y same , etc. I will not be meticulous enough when Idk what I'm doing. I'm also getting tired of walking out there to fail, lol I'm like in the center of the block's viewing area for every home, out there 5 days a week with multimeter like I know something, gawd, they must think I'm a clown, lol
@blackopal3138
Жыл бұрын
@@LehewTech 2009 Laramie 5.7, remote start/anti-theft -- it only has 68K miles. Under the steering wheel/dash is spotless, under hood is pretty clean, harnesses still all taped, I had to cut a tube open to find that wire, I checked all connectors, no rust all fit good and snug, fuses all look good, haven't cnty. checked all..... Idk, I figure if you are going to take a stab, I really appreciate that, so I figure it's only 2 mins reading to give you the most info I can, Idk, what's relevant....
@timmyjurich8318
Жыл бұрын
So if you troubleshoot your starter in the car does not start that could mean there’s a problem with the starter, battery, or engine seizing?
@mminniear984
3 жыл бұрын
Very helpful video. I’m having an issue where when I turn the key, sometimes it takes to to 3-4 seconds of holding the key over before it starts. I had the starter replaced this past weekend but the issue is still happening. Before I had the starter replaced, I had a couple instances where it wouldn’t start on the first key turn. But I turned it over and over a few times and it would start. Then be fine a bunch of starts in the future and do it again in a while. Any advice? Thank you!
@mikeburdi3464
Жыл бұрын
I don't know if you fixed your issue but it kind of sounds like the crank sensor. Hope everything worked out for you!
@dawnmarie55
Жыл бұрын
@@mikeburdi3464 ok, I'm having this same issue. When I start it up it seems as if it's the starter going out. Now I had my crank sensor replaced and my check engine light still comes on. While driving over a certain amount of miles my check engine light will come on and my truck will start slowing down.
@rochellecornet284
10 ай бұрын
@@mikeburdi3464 is the crank sensor the same as the win module?
@mikeburdi3464
10 ай бұрын
@@rochellecornet284 No, the crank sensor is on the engine located by the crankshaft, usually by the harmonic balancer. The WIN module is in the vehicle, part of your ignition switch. But they cause 2 different symptoms.
@rochellecornet284
10 ай бұрын
@@mikeburdi3464Thank you for the reply and informative answer.
@colbybyrne4080
Жыл бұрын
I have a 2009 Ram and it will crank for a little while every time then turn over
@coutz56
Жыл бұрын
Thank you
@dmsmith1980
2 жыл бұрын
Thanks for the video. My 2011 wouldn't crank. I tried to jumper the relay and nothing. I arched the solenoid and got the starter to spin. After that i could use the ignition to start. I'm still not quite sure of the problem it could be the starter or the signal wire from the relay.
@RS-yx7er
Жыл бұрын
Did u find out y I'm having the same problem
@dmsmith1980
Жыл бұрын
@@RS-yx7er It continued to happen intermittently and I eventually came to the conclusion that the starter needed replacing. No problems since.
@franciscohunter4422
2 жыл бұрын
He hi brother I have a 2012 Dodge Ram 3500 with the 6.7 Diesel engine I would want to know where is locate the ac compressor relay
@speecron
6 ай бұрын
Also helped unlock alarm lock down
@ebaab1976
3 жыл бұрын
I have a 2011 Ram 1500 and recently its been possessed. I turn the key and it cranks but no start. Sometimes I put it in neutral, back to park and it starts but then engine immediately shuts off. Happens when starting in neutral as well and usually after 4 or 5 tries, it finally stays on and runs good to go. The more i drive it in the day the less it happens when i restart the same day. The next day I have to do the whole 4-5 times again for that initial start of the day. No engine codes at all. Battery is brand new. I have no idea what the issue is but thinking it might be related to this video.
@LehewTech
3 жыл бұрын
Have you tried cycling the key on and off about 10 times.before cranking the engine over? It sounds like your fuel pump may be loosing prime.
@ebaab1976
3 жыл бұрын
@@LehewTech Funny you say that because I have made the comment to my mechanic that its almost like its a lawn mower that needs to be primed....lol. I did order the pump bypass cable for the TIPM that also seems to be a fix for the issue at hand. I guess we will see. I do plan to buy a new starter relay and 40A Jcase fuse as well just for principle.
@dalebryce3511
2 жыл бұрын
I have the same problem. Thought it was loosing prime but have went through the entire fuel system new. But crank no start 2 or 3 times every morning. After it starts it's fine the whole day
@ebaab1976
2 жыл бұрын
@@dalebryce3511 I changed batteries, fuses, added the TIPM relay bypass and nothing. Still died. Got to the point of disconnecting the battery at night just so it wouldnt be dead in the morning. Basically was told I would have to replace the whole box most likely. Said screw it and traded it in on a new Chevy truck a week after I posted.
@ipodman38
11 ай бұрын
Jumping starter relay still no crank
@kilobear1979
3 ай бұрын
I have a 14 ram 1500 and my drivers headlight goes out and parking light under it flashes but when I push or move starter solenoid relay it works like normal again 🤔 no other issues with the truck. I push pull wiggles everything else on fuse box but only that relay does it. Any ideas thx
@josephmilton1873
7 ай бұрын
I put a new battery in put on charger and it still won't start?? What should I do?
@benjaminroemeling9917
10 ай бұрын
thanks for the video, I have a 2012 ram 5500. It sat for 9 months or so and now won’t start. All the fuses you had us check look good. I took the relay out and jumped it with a paper clip and it worked. Ingot a new relay and it’s still not starting. I do have a red flashing light on the dash. Any other ideas?
@williamhartley4752
5 ай бұрын
Throttle control sensor module
@charliefleming1645
Жыл бұрын
Did u have to take battery a lose first
@NevilofMars
2 жыл бұрын
2011 RAM 1500, solenoid just clicking when key turned. Tried all the tips in the video. None worked. Found the solenoid/starter connections needed to be cleaned. Once cleaned, truck starts like it is supposed to.
@luismt2394
2 жыл бұрын
Hows the cleaning process?
@grasshoffers
Жыл бұрын
So the starter test showed my truck starter works fine. When I turn the key, the starter might go a bit then stop and clicking abounds, sometimes ‘service 4WD’ pops up. I had a new engine dropped in a few months ago and it ran without issue. Still have not made it to the first 500mile oil change. Battery is new and charged. Red light I g bolt and such. A year and a half ago dealer put in new ‘brain’ and harness. I did try in neutral as well.
@tylerberryman4079
Жыл бұрын
Did you ever figure out what was going on
@grasshoffers
Жыл бұрын
@@tylerberryman4079 one of the ground wires for the TIPM was loose. The guy who installed the engine said he had not tightened it enough and it had worked itself loose.
@iidentifyasskinny
2 жыл бұрын
I think my other comment didn't post... I tried the manual bridge and got a couple tiny sparks and a faint clicking noise, but nothing beyond that. Is the clicking noise an indicator of anything?
@mikeburdi3464
Жыл бұрын
Yes, your starter is more than likely bad. You can jump the starter directly by putting a booster cable directly to the starter solenoid, the starter should engage. That is for testing purposes only, and make sure that everything is clear of any moving parts. Hope everything works out for you!
@mtdman1146
Жыл бұрын
I have a 2011 1500 sport with console shifter and key fob. When I turn the key I get no crank or anything. My truck also won't come out of park. I tried all of these steps, disassembled and cleaned the WIN module contacts. Still no luck. Any ideas?
@cliffroberts1774
Жыл бұрын
Did you figure it out?
@thomasdube2994
Жыл бұрын
This might sound like a silly question, but will this same trouble shooting work for a 2011 2500 6.7 as well?
@nestorcortez1474
6 ай бұрын
It will
@korvein187
2 жыл бұрын
I should of watched this fucking video before I went out and bought and replaced my starter
@kippeddy1349
2 жыл бұрын
My 2014 dodge ram 5.7 won't crank over battery is good dash and headlight come on but wont turn over, any help is appreciated.thanks.
@cliffroberts1774
Жыл бұрын
What was the problem
@robertsenior8330
3 жыл бұрын
2012 ram 2500 5.7. When trying to start periodically the power in the truck goes out(like a win module fail, without the key being stuck). I go over to the battery and i hear buzzing and rapid clicking coming from the start relay fuse.. i disconnect the positive battery lead for a min and then reconnect. Sometimes i have to do it more than once. Im guessing the starter relay is bad. Im going to swap it with the same fuse from hvac slot. I’ll have to order new ones… Im beginning to hate dodge. 99k miles and it’s decided to fail in multiple areas. Ive done all my pm’s in a timely manner and one system after another fails. Btw ive stopped making fun of ford.. but chevy is still fair game. 😂😂😂
@painterjr
2 жыл бұрын
Did you figure out the fuse? Or the issue with this? Thanks in advance
@robertsenior8330
2 жыл бұрын
@@painterjr turns out it was the battery post connectors. Pos was cracked and neg was not getting a Good connection. I also replaced a bunch of fuses afterward just in case.
@painterjr
2 жыл бұрын
Much appreciated
@robertsenior8330
2 жыл бұрын
@@painterjr no problem. I also noticed my fuses posts were oxidized, my connectors around and going into the fuse box … wires were oxidzed. I cleaned all that up. I also sealed the fuse box. New gasket and sealed the wire port. Sealed all the external connectors as well. Ram did a horrible job protecting the electronics and wiring on these trucks. Loose wires in the dash can rub and short. They need to pick up their game or i wont get another one.
@robertsenior8330
2 жыл бұрын
@@painterjr good luck with your truck. If you need ideas to troubleshoot … hit me up. I’ll get back to you asap after i get done at the ranch.
@tinabare8716
Жыл бұрын
Hi I came across your video and I have a 2011 dodge ram and when to crank it on the dash it says no fuse could you possibly help me and tell me what this means please
@jorgealonso6260
Жыл бұрын
Did you fix it ? If so what was the problem
@rangerb44
11 ай бұрын
ok, ive done all of this, what do you do when the starter is just doing a knock, and not turning the engine? it sounds like the gears are hitting a wall. brand new starter, still no crank at all.
@LehewTech
11 ай бұрын
Check for a seized engine
@rangerb44
11 ай бұрын
we did check, it is not seized. we are attempting to change the neutral safety switch now, but cant seam to find it anywhere. its a 2012 ram 1500 5.7 hemi @@LehewTech
@CJofPbs
5 ай бұрын
@@rangerb44 did you figure out the issue?
@MCTeletubbie
3 жыл бұрын
Why didn’t it turn on?
@billyrichards8557
Жыл бұрын
key was not in the on position
@user-yk1ew1qq8z
Жыл бұрын
I got a 2011 Ram 1500 no crank no start not even a sound. Lights radio and windows work but won't crank. Checked starter works fine and engine is not seized. I can't seem to find the issue
@danielnoren315
Жыл бұрын
Hello! I have the same problem with my 2011 Ram 1500. When I turns the key the fan and stereo works. When I turn the key to start the fan and stereo dies. No klick from the starter, nothing happens. Do someone have any ideas? Thanks!
@cliffroberts1774
Жыл бұрын
Same issue did you figure it
@carrierichardson7606
11 ай бұрын
I have a 2013 ram 1500 SLT 5.7 that would not start
@konstantinarsienko7966
3 жыл бұрын
My 2013 RAM 1500 is cranking but not starting and I am at the end of my wit.... I parked it in perfect working order and was charging battery once a week or so and when I lapsed the battery died. Now it won't start even after I put in a new battery (battery tester said REPLACE as it was close to 40% of its life, I still had old OEM one). There were multiple codes including feared tranny lightning bolt but most seem to be related to low power. After battery replacement I have no check engine light and no tranny light. I did not yet reset any previous codes. It still cranks the same as before but no start. I checked fuel pump with bypass cable and I can hear it working but still no start. I see RMP gauge only barely moving (is this normal?). Also very strange, when I put key in it it says low fuel (I have full tank), but after key goes into ON and then START, it detects full tank. Can you suggest anything else I can try? I am going to check starter relay as per your video, but wonder if there is anything else as starter seems to be working (cranking). Thank you.
@LehewTech
3 жыл бұрын
If the engine is cranking then you need to determine if you have ignition (spark plugs being fired?) and fuel pressure
Пікірлер: 92