My man goes hard. Not only is he smart. Not to mention bending the tooth brush with heat, but then at the end, he floors that puppy all up and down his street proving it was fixed! Nice video Joe!
@RissaChante
3 жыл бұрын
Thank you! I have tried everything. Replace my mass air flow sensor twice. I've replaced the valve cover, spark plugs, coils, pig tails, air filter and this was the only thing that worked. Mechanic after mechanic, til my 15 year son saw this and did everything you said and the problem stopped. It only cost me about $6 for a can of throttle body cleaner. Thank you!
@joen2521
3 жыл бұрын
That's great to hear
@legacybrand1993
2 жыл бұрын
Were you having the same issues as the these year models .?? I’m lagging acceleration and I’m thinking it’s my APP Sensor. Did you have yours replaced and confirmed ..?
@PrayerChanges24
3 ай бұрын
That’s great I believe that’s what’s going on with my Nissan Altima 2011 2.5s hesitation when pulling off goes up to 20 miles then it makes this humming sound won’t go no further than 20 miles.🤦🏽♀️
@PrayerChanges24
3 ай бұрын
It jerk a little pulling off then it picks up speed drive normal just won’t to know is this may be the issues? With my 2011 Nissan Altima 2.5s
@pheal_
11 күн бұрын
@@PrayerChanges24did you get this fixed and how?
@tonydodd1
Жыл бұрын
Thanks. I had the hesitation with my 2011 Nissan Quest. Couple of Auto repair shops said replace tranny at $4000+. Followed your steps and discovered the intake hose had a hole in it. Replaced and now no issues with hesitation. PTL 😊
@commonsense4205
3 жыл бұрын
I have been looking for this solution for months over the internet. Finally found the right solution for my problem, and for that, I thank you.
@eastreedleyjuggking4226
3 жыл бұрын
Did it just as described and so far so good. I like how he gave all the description and angles. My car is a 2008 altima SL i just replaced the catalytic converter and new sparkplugs and coils and had the problem still, so once i tried this method it solved the problem. So far so good👌💪
@LookAtLilDude
3 жыл бұрын
I do as well which problem was it, like ehat should i try first. No one wants to even buy my car now
@flaplaya
3 жыл бұрын
Cleaning the throttle body and sensors like this nice man explained in video. These cars have almost zero value blame the CV Transmission for that. Oh and if anyone's car goes in limp mode in summer add plate and fin oil cooler for Transmission.
@jasonjones787
3 жыл бұрын
One other thing to inspect that he did not mention, check the vent hose (accordion looking hose) look in between the gaps for splits or holes. I had everything he did here done to mine and I also had to replace the vent hose because it had several splits and holes in. Otherwise he is correct on this will fix that problem.
@noeponce4690
2 жыл бұрын
Thank you for sharing this tip. I didn’t inspect the vent hose until I read your comment and sure enough, it was cracked. After replacing it, it running smooth no hesitation at all. I Did everything else he did on the video. Thank you so much. God Bless you.
@BlackWhite-ru8gm
2 жыл бұрын
@@noeponce4690 where is the vent hose?
@asphaltcowboy7868
2 жыл бұрын
Cleaning the intake helps a lot with pretty much any car...the maf also helps a lot to be cleaned at a regular maintenance time..but remember with the maf..it's takes a special Cleaner because it is a sensor..and most common cleaners will leave a residue behind causing more problems..so when it comes to Cleaning many off these parts..make sure to use the correct Cleaning solvents..great video btw..
@pungalo16
2 ай бұрын
Thank you for posting this. You saved me about $460 in speed sensors and the unnecessary down time on my vehicle. "ALOHA & MAHALO"
@petermartinez5573
3 жыл бұрын
Great video. Short, sweet and right to the point. Thanks for sharing this information, I am thinking of including this as part of my preventative maintenance.
@joshuabucklen98
Жыл бұрын
Whats up pete
@CarlosGonzalez-mr5qz
5 ай бұрын
This is a great video, but it didn't take care of the problem. It turns out it was my air intake hose. It had a big tear. Replaced it and problem solved! I did clean the throttle body though. It was very gummed up. Looks shiny and new again!
@naeallen5821
2 жыл бұрын
I have a 2011 Nissan Altima JUST LIKE THIS ! I have replaced my mass airflow sensor 2 times . I also did a fuel injector cleaner 1 time . Problem still occurred . The problem is when I crank it it idles high then low repeatedly then sits a loud idle . When I approach red lights it stops completely as it should but when the light turns green and I press the gas it kinda of jumps . Nevertheless it stalls when I get at certain speeds sometimes . I’m going to replace my throttle bottle and pray all these problems stop. Thanks for the video
@BizzyTC
Жыл бұрын
Did it fix it ?
@edwinalexander1170
Жыл бұрын
Change your spark plugs, Coils, clean Camshaft sensor, crank shaft sensor, and clean catalytic converter, look also at the air intake hose pipe may be it has cranked and passes more air try replace this pipe, change your air cleaner too.
@joen2521
2 жыл бұрын
It ran good from Sept 2020 to Jan 2022. Then it started showing early signs of hesitation again. This time I only removed the black plastic air duct that connects to the throttle body and sprayed cleaner into the throttle body without removing it from its mount. It solved the problem and it’s back running well without hesitation. I’m expecting that at some point I may need to replace the throttle body because car parts need maintenance but are not designed to last indefinitely.
@jessetorres4212
2 жыл бұрын
Pretty neat cleaning job, and please, be aware that after doing that...You may also need further help with your throttle body so, it can be reprogrammed by watching another video or so. Good job😁👍
@deltoasuka7085
Жыл бұрын
Thnx for saying the vid bro
@bluedragonweb9127
2 жыл бұрын
Worked perfectly. I also found out that the air filter that a really "jiffy" lube shop charged my daughter to replace looked like the original from the factory ( 2008).
@brentphillips262
2 жыл бұрын
Never use Jiffy Lube. Mechanics are low trained and work on commission.
@derricka4525
2 ай бұрын
Jiffy Lube didn't even put my air filter cover back on correctly.
@suspectedcrab
Жыл бұрын
I've owned a 2009 for 9 years and I don't think my air filter's ever been changed until today. My engine would hestitate once in a rare while when trying to accelerate from a complete stop, never going above 40. It's problematic when you're trying to merge after a right turn... The plastic intake hose leading up to the air filter box was also loose, so I just duct taped it. It was a little more loose than yours. I dont think that's a big deal if it's before the air filter, but the duct tape should prevent any excess dirt/dust coming in where it shouldn't.
@sntcz8
Жыл бұрын
Same exact issue with my 2008 nissan Altima, and with no light on Board. Did everything you did in the beginning, even installing new throttle body. It ended up being my ignition coils, when engine light decided to come on 🙄. A complete tuneup solved my problem.
@markbajek2541
3 жыл бұрын
Rarely , but sometimes there are a ton of leaves and debris clogging the air filter intake piece (the curvy bit) near the front of the car.
@LynchDaddy78
10 ай бұрын
Great video with a lot of good information and tips. My son's 2011 Altima is hesitating. I'll work on it with him. Thanks and cheers.🥃
@nikeswag10
3 жыл бұрын
Also check your pcv valve because it can cause that as well
@leslyeangulo732
2 жыл бұрын
Thank you so much for making this video. I took my car to many mecanics and no one knew what it was. Bought a new air flow sensor. And that didn't fix the problem. So thank you for such a detailed video. Made it easier. It fixed the problem. Thank you, thank you, thank you. 🙌
@cherokeeblk7625
2 жыл бұрын
Great video and awesome step by step I'm also a mechanic and you're a very great teacher best video right up there with Scotty kilmore thanks bud this helped me fix a friend's Nissan
@danielwillliams9669
3 жыл бұрын
Thank you. I thought it might the infamous beginning transmission issue. But I am sure this is the problem.
@LA562mike
2 жыл бұрын
Did your engine make a weird noise too
@danielwillliams9669
2 жыл бұрын
@@LA562mike it did, but I come to find out it was a bad belt tensioner. Usually the throttle body will need cleaning if you add too much oil. My noise would start on cold mornings and after research, it was stated the cause was the belt tensioner. If it's your belt tensioner - becareful removing them - they can easily snap off in the block. Do not use old bolts - replace with grade 8 bolts.
@bendixsmith9642
3 жыл бұрын
Great Video When you gonna touch or move the throttle body butterfly valve after the cleaning you have to re learn the Body throttle, here is how to Relearn the body throttle for all Nissan Altima, cause i have the same problem i try this method. ( Fully released the accelerator pedal and keep it for approx. (20 seconds unit the Engine light stops blinking and turn On not start the engine only turn On). (Fully release the accelerator pedal with 3 seconds after the Engine light OFF). (After Start the engine and let it idle for 5min the body throttle gonna Relearn). Thank you
@DonJulio510
3 жыл бұрын
Even if you disconnect the battery?
@bendixsmith9642
3 жыл бұрын
@@DonJulio510 Yes even you disconnect the battery you have to re learn the body throttle
@noeponce4690
2 жыл бұрын
Thank you very much. Save me a lot of money. Thanks to people like you I started doing things myself, you encourage me to do so. Make things look so easy. Thanks again.
@derricka4525
2 ай бұрын
Good video. I just wish you had showed video of the problem. I have a hesitation between 10-20 mph, not all the time but often. I was almost rear ended recently because acceleration stopped and I just crawled along at 10 mph until it kicked in. I will give the cleaning a try.
@Twobarpsi
Жыл бұрын
Great tips!! Especially the one on bending the toothbrush!
@yohanonshine4664
3 жыл бұрын
I usually do the plugs also when doing this also after cleaning throttle body do a throttle body position sensor reset it's a key on and off three times till engine lights flashing and hold pedal to the floor till the flashing engine lights turns on solid.
@LSamo
3 жыл бұрын
Can you explain it steb by step? Thank you!
@yohanonshine4664
3 жыл бұрын
@@LSamo search KZitem for Easy throttle body sensor reset for nissan its simple
@zarron221
8 ай бұрын
Exactly wat my car is doing! Great job nakama friend Shalum
@dondada1949
9 ай бұрын
Why does my car experience surges when idling? I recently had my ignition coils, spark plugs, and air filter replaced, and I've noticed a slight surging sensation, even though the RPM doesn't fluctuate. No codes
@Cripp12
2 жыл бұрын
Thanks. I had same issue. Finished cleaning everything and noticed a big hole in the hose as I was putting everything back. Seems to have worked. Thanks
@nicholasvonrhine6311
2 жыл бұрын
Yes people maintaining the throttle is very very important.
@reysteffani62
3 жыл бұрын
Thank you much. I have a 2003 Nissan Sentra that hecitates as well. I'm going to try everything that you just did to see if I could fix mine. Thanks again.
@marcelavaldivia5456
3 жыл бұрын
So tell us did it work
@billcox199
2 жыл бұрын
Most likely need an Air idle volume learn after cleaning .Will idle higher after cleaning throttle body and set a code for throttle body and or lean condition. Done with Nissan Consult.
@charleschimfwembe5528
2 жыл бұрын
I have been having these same problems with my nissan cars. But none on my Toyota cars. Nissan should improve their cars.
@enrgmusicinc
3 жыл бұрын
Gonna try this..... I’ve done new air filter spark plugs and cleaned throttle body. Will update ASAP
@ivang3860
3 жыл бұрын
Did this procedure worked for your vehicle?
@jayc5158
3 жыл бұрын
Any updates?
@m2k2n2d
Жыл бұрын
I need to do the same for Nissan Altima 2015 S. Great Video and very helpful.
@j.edgarmolina5654
3 жыл бұрын
Thanks for the video,it help me with the problem that I have with my car
@jorgetomas380
2 жыл бұрын
Great video. My 2004 nissan pathfinder has 140k & has been doing thee same exact thing. Serious bucking upon acceleration. Will be getting a new throttle body & coils/spark plugs. (I'm heavy on preventative maintenance) My mechanic had trouble figuring it out. He did say mainly this. Thanks for the informative video.
@carfeenz
2 жыл бұрын
Did it fix the problem?
@jorgetomas380
2 жыл бұрын
@@carfeenz, found out by chance, thinking it was a bad solenoid valve, it was a hole in the tube that connects the solenoid to manifold.
@carfeenz
2 жыл бұрын
@@jorgetomas380 interesting, ok thanks !
@BillSW
Жыл бұрын
@@jorgetomas380 where is this solenoid valve? is it part of coil or throttle body?
@apostasiaelegcho5612
2 жыл бұрын
What if you press the accelerator all the way to the floor and your won't move?
@jerrellhoggard6599
6 ай бұрын
Coil pack power pack
@user-fc5lw8kf7y
2 ай бұрын
I appreciate your video Joe!
@asphaltcowboy7868
2 жыл бұрын
Vacuum leak around your intake manifold..dirty intake throttle body.. clogged egr Vale..many things can lead to hesitation..but these 3 are your cheapest and most common problems.. mostly hesitation comes from dirtiness..
@OLIVER949OC2
2 жыл бұрын
I fixed it bro thanks I thought it was stuck tranny slipping or sensor was off but all it was a grimmy dirty throttle body
@VornVann
Жыл бұрын
Thank You for sharing the video...SIR
@backendninja8333
2 ай бұрын
My car runs good in the morning after start. Then the hesitation comes after driving for 10 mins. No check light. Anyone can guide me why it hesitates after 10 mins of driving?
@jdmforever5583
2 жыл бұрын
Good idea after cleaning mass air flow sensor to let it dry before reinstalling
@jennifer_ross_
Жыл бұрын
All my sensors are plugged in but my check engine light did come on after I cleaned the throttle body
@lackslink
19 күн бұрын
Hey Joe! The only time I experience these hesitations in my 2011 Nissan Altima is after I've driven the car for a decent amount of time, especially after coming right off the highway. Is that common or might it be something else?
@nolaboxingevents4287
2 жыл бұрын
I'm having trouble with my 2012 nissan altima... the problem is that when I start driving it takes a long time to accelerate and it don't have no power. Car can't go over 40 miles... and when I drive I hear whining noises as I speed up.. can anybody think what would be the problem
@PrayerChanges24
3 ай бұрын
You aren’t alone my 2011 Nissan Altima only went up to 20 miles🤦🏽♀️ it goes into reverse, goes into drive no problem. When cranking the car up, The idling is loud after that sounds good. Pulling off to drive the car, its little loud everybody ask me what is that sound with your car? My brother bought me the car from a private owner I believe the car was as is. Probably knew it needed work done on it this was in 2021 my brother bought the car for me. Waiting now once the mechanic put the car on diagnostic machine and go from there to see what issue(s) is.
@Thelootsteala
15 күн бұрын
@@PrayerChanges24do you have an update on what fixed the problem ? My 2011 is currently doing the same thing
@PrayerChanges24
15 күн бұрын
I bought 3 quarts of transmission fluid, my brother told me that I needed 3 more bottles of fluid and see if the car pick more speed. My car didn’t have noooo transmission fluid in it, bone dry!! Believe once I get more fluid 3 more quarts praying it will drive okay 🙌🏽that’s was causing the car to jerk. Again once the car pass 20 miles it drove normal; type of fluid you need is: Vavoline Full Synthetic Transmission Fluid CVT ( continuously) Make sure you buy this type of fluid. After putting the first 3 quarts in, car still making that humming sound not as bad as it did before. So I’m getting 3 more quarts, pray everything works out for you sir.
@PrayerChanges24
15 күн бұрын
@@Thelootsteala Also I have to get my air filter change as well, and oil change. Was getting my oil change when my car started acting up.
@mikegamba580
Жыл бұрын
My 2007 Altima 2.5 has no fuel filter you can easily change apparently their is a screen on the bottom of the fuel pump that's in the tank and my car goes no where from a stop sometimes
@joen2521
3 жыл бұрын
In my case, although it may be hard to see in the video, the throttle body had excessive carbon build up on the outer edge of the valve and on the inner cavity wall. This would compromise the seal which is intended to be created when the valve is in the closed position.
@TheWinterState
3 жыл бұрын
Can you show how to relearn, because we decided to this very work...and now the idle is too high
@joen2521
3 жыл бұрын
@@TheWinterState To get the onboard computer to reset, just remove the negative battery terminal and wait around 30 seconds before you reconnect it. Hope that solves the issue.
@TheWinterState
3 жыл бұрын
Unfortunately this didn’t work, and my car is exactly like yours...Nissan will now have to do this for me 🤧🤧
@joen2521
3 жыл бұрын
@@TheWinterState I wish I was there to see it with you. My only other advice is that since it wasn’t idling fast before, something may have changed around the throttle body area. Cleaning won’t cause it idle faster. However, you check: • The butterfly valve inside the throttle body opens and closes freely • The small rubber gasket is set in place. This is where the throttle body and intake manifold come together. • The throttle body is resting flat on the intake manifold • The connector to the throttle body sensor is fully plugged in
@TheWinterState
3 жыл бұрын
Found out my car was manufactured in California but I live here in Florida...
@phil_so_good9642
8 ай бұрын
Thank you, that fixed the issue
@claytonsturgill5340
2 ай бұрын
This didn't fix my car any idea what it could be
@kevinguadamuz5510
4 ай бұрын
The 4 banger made me a subscriber and I liked the video
@mitchelllong5848
3 жыл бұрын
After messing with the throttle body and the sensor that goes to it would've been good to do the throttle body relearn procedure
@joen2521
2 жыл бұрын
Good point, that’s something I should have clarified on the video. With the battery disconnect, the on-board computer has no way of determining that the butterfly valve was moved. Unless by moving it with too much force, something physically becomes off-reference so just be careful when moving it. There are many videos that others have posted on how to reset the throttle body and it may be good to be prepared if that issue does occur.
@user-fi1cl6hq2z
4 ай бұрын
excellent video
@angelofgod371
3 жыл бұрын
The check engine light would not come on cause you unplug the battery right? So that wouldn’t really mean it fixed the problem cause the check engine light did not come on.
@scullcandy10
3 жыл бұрын
My Nissan Altima won’t chime when I start it do you know the issue with that
@alananaccarato6315
3 жыл бұрын
you're a life saver!!!
@rajatsahi5422
2 жыл бұрын
My car does the same and wont let me go above 2400rpm. It also gives a code for mass airflow sensor, that i replaced but it didn't help, and the light that comes on when the skids on ice, stays on. Hopefully this helps with that
@DemiGod101
5 ай бұрын
Did it work?
@rajatsahi5422
5 ай бұрын
@@DemiGod101 yep, been over 2 years since I had that issue
@lillpete64
Жыл бұрын
Very same problem with 2012 altima 4 banger mine is shuddering when I hit the gas pedal w/ check engine lite on
@siphomathe8210
Жыл бұрын
I will try this causes I checked evap purge valve , maf from 1998 Volvo s70 but no lucky.
@ltsmum3316
Жыл бұрын
Isn't the check engine light gone because you disconnected the battery?
@tebelleh
4 ай бұрын
Actually bending inward on the toothbrush would have been best
@snoopyny
2 жыл бұрын
Thanks so much simple and easy..
@PianomanRay
2 жыл бұрын
This is great to know. I will give this a try. Because I have a 2017 Nissan Altima SV that when I mash down on the pedal it takes its time then a few seconds later it wants to hit fast pace. The first check engine reading said it had a misfire. Since the light is off should I double check that first?
@Cook2430
2 жыл бұрын
My 2002 does the same thing. I suspect mine is plugs and coil packs are due for a change.
@shellyblanchard260
2 жыл бұрын
Why on my 3.4 nissan altima only does it at take off on low speeds. I have tinapply more or less gas to calm it ?
@kingkobra91yt46
2 жыл бұрын
i have a 2013 nissan sentra and it does the same thing took it to a mechanic and he said its the throttle body is there a way i can clean it
@michaelojeda8567
10 ай бұрын
After cleaning the throttle body? Do you have to do the relearn test?
@BillSW
Жыл бұрын
where did u spray in the housing of throttle body just before reinstalling throttle body? at 7:57?
@Real_Rob_Reels
Жыл бұрын
LOL--- No, the gook is not why your Nissan is stalling in the middle of traffic. Chances are it's the Camshaft & Crankshaft Position Sensors (which should be changed at the same time). It's very common with these cars. This guy here-although I appreciate the time and effort he put into this video---doesn't seem to really understand a lot about being a technician-- maybe as a mechanic he is good. :)
@oneb4393
3 жыл бұрын
Thank you so much 🙏
@jpyr0_tv192
2 жыл бұрын
My Altima 2007 I press the gas to the limit and it won’t accelerate I have no idea , what that can be , but once the car pass 10mph then it’s all good it start to accelerate fine
@eduardomadrigal584
Жыл бұрын
Who knows if your car wasn’t working properly ? You didn’t show how your car was working before you clean the throttle body
@Hullified
Жыл бұрын
You had me until you used the same solution on the MAF. unless you used MAF cleaner on the throttle body.
@jamesjones5799
2 жыл бұрын
Having trouble with my 07 Altima after replacing the brake booster and master cylinder pedal went stiff. Anybody know what's next step it's at 3rd shop now nobody seems to know why that is happening.hoping 3rd id the charm
@jlokslopez9929
4 ай бұрын
Does the throttle body have to be relearned after cleaning?
@joen2521
4 ай бұрын
Only if you left the battery connect. If the battery is disconnected, the cars computer will not detect that you moved the throttle so does not need to relearn. That’s what I did in the video.
@douglaslopez3898
Жыл бұрын
Great video thank you 🙏 so much for that.
@mafridi106
2 жыл бұрын
Hi Joe, I’m having the same issue with my ‘07 Altima. Just curious how your car is doing? Still running good without hesitation?
@donaldcassidy1592
2 жыл бұрын
Super job!
@Fredleea77
3 жыл бұрын
Will this be the same for 2011 Infiniti M37x made by Nissan? Car having same issue
@joen2521
3 жыл бұрын
Yes, but all 3 located in different locations around the engine as you would expect.
@justinworkman9980
2 жыл бұрын
Its the cvt transmission doing that
@EqualityEmpowers
2 жыл бұрын
I have a 2011 Altima, 105,000 roughly. Engine cuts out and loses power when driving, even in neutral. It has good fuel pressure, put in a new crank sensor. Starts better but still cuts out randomly and can duplicate it. Codes for ABS module and 1130 brake module code. Trans code said engine RPM signal is missing communication. Also not the pedal sensor. someone help :(
@thunderbear4254
2 жыл бұрын
Fuel injectors sound like they're dirty and need to be cleaned or replaced.
@jadubb4639
3 жыл бұрын
Should I replace my spark plugs I’m dealing with the same thing
@joen2521
3 жыл бұрын
it's possible for faulty plugs to cause hesitation. My service manual says to replace them at 96,000km but I haven't replaced mine and it still runs fine.
@nikeswag10
3 жыл бұрын
Check you air filter, then mass sensor sensor, then pcv valve and the hoses with it
@zongiefmata2226
3 жыл бұрын
Thank you 🚙
@mohammadsalehi3450
3 жыл бұрын
It's a great video. My Nissan altima recently failed smog check. Today I went to Mossy Nissan to fix my check engine light, they said I should replace the throttle body costs $1280! I didn't see your video then and one of my friends did something like you and tried to reach back of throttle from the front side. Since didn't watch the video didn't risk to go for other side. However the car now works well. I am not sure if the check engine light will come back. 🤔 Do you think if I go for second smog check, my car can pass?
@joen2521
3 жыл бұрын
There are many things that could cause it to fail a smog check like EGR valve, O2 sensors, catalytic converter, gaskets, restrictions to exhaust and others. Everything is integrated with each other so it’s too hard to say.
@sheeshalready
2 жыл бұрын
My 2007 definitely needed the 3 steps, especially the throttle body...what a mess! Afterward, it required the throttle re-learn, which the pedal procedures failed at correcting. Luckily, I have a good scan tool that included the re-learn function. However, that darn sporadic hesitation is still occurring...ARGH! Any other ideas?
@kuzmanovskinikolce
5 ай бұрын
What kind of scanner you have for re-learn procedure?
@sheeshalready
5 ай бұрын
@@kuzmanovskinikolce I got a great deal on that Thinkdiag dongle type scanner. It came with one year of subs for all makes and models. I was able to do the relearn, program new key fobs. I was also able to program new keys for my pt cruiser. Very good item. However, once the subs run out, you have to pay for what you want. I have yet to do so because I have not needed that level of scan tool since that time. It still works as a regular OB2 scanner, and when I actually need to do something above that, I will have to pay for the sub for one make at a time. Not sure the cost, but I think it is around $40 for one, for a year. That hesitation with the Nissan is still there, but it happens rarely, and pretty much when you start off, give it gas, then let up, then give it gas again, there, that is when it hesitates for a hot second, if that makes sense.
@chukob5
2 жыл бұрын
Not to blame you since I was willing to try anything but I did the throttle body cleaning yesterday. Today my 2010 Nissan Altima is totaled something came loose in the engine and it now sound like a rock tumbler
@terrelle5087
Жыл бұрын
Damn Stuff like that takes it to a shop if u don't know what u doing.
@chukob5
Жыл бұрын
@@terrelle5087 lol i can clean a throttle body my friend
@terrelle5087
Жыл бұрын
@@chukob5 obviously u can't if u follow this video n totaled your vehicle the process.. Not trying to be funny
@chukob5
Жыл бұрын
@@terrelle5087 what makes you think the problem is related?
@chukob5
Жыл бұрын
@@terrelle5087 key words…. “i was willing to try anything” …. Meaning the car was already fucked
@bobbyatman273
3 жыл бұрын
What's the cause if hesitation begins after 82 mph on same year and model? Accompanied by a Very noticeable vibration (which can be bad wheel balancing after new tires were just installed)
@bruceadonnelly69
3 жыл бұрын
CVT trans
@totallyn2wilsongs
2 жыл бұрын
Regarding the vibration, it could possibly be broken motor mounts if you haven't considered that.
@Stingnu
2 жыл бұрын
Check your lower control arm bushings, mine went bad and sound similar.
@bilalqureshi2489
2 жыл бұрын
I have 2014 Nissan Altima 2.5L S I want to clean my throttle body but mechanic told me if you clean throttle body your throttle body alignment is gone then you have to change your throttle body please help me out may I clean my throttle body thank you
@joen2521
2 жыл бұрын
Whenever a throttle body is replaced, it needs to have a re-learn procedure done. However, if you remove the negative post from the battery and only clean the throttle body, then it normally won’t need a re-learn procedure. This is because the cars onboard computer is off when the battery is disconnected. Another mechanics opinion may be helpful and there are also many videos showing the re-learn procedure to help you be better informed when speaking with a mechanic. Hope this helps...good luck. kzitem.info/news/bejne/pIhjp55-fKWdm6g
@bilalqureshi2489
2 жыл бұрын
I have 2014 Altima and you have 2011 both have same method to clean throttle body I want to just clean my throttle body and I don’t wanna change thank you 😊
@kellycarmouche7452
2 жыл бұрын
Thanks!
@kortdogg88
Жыл бұрын
Good video
@muhamedvelovic227
2 жыл бұрын
Good job
@dwaynehall7231
3 жыл бұрын
U move the butterfly, some other videos say don't move it
@joen2521
3 жыл бұрын
Good point, that’s something I should have clarified on the video. With the battery disconnect, the on-board computer has no way of determining that the butterfly valve was moved. Unless by moving it with too much force, something physically becomes off-reference so just be careful when moving it. There’s many videos that others have posted on how to reset the throttle body and it may be good to be prepared if an issue does occur.
@lashg
3 жыл бұрын
I'm on my way to Autozone right now
@gilbertlee860
3 жыл бұрын
Dude. This issue has been bothering me for a long time.. d u fix it?? The Nissan dealer told me that I hv to pay $3000 to fix it. Wtf..
@KingTheGermanShepherd
3 жыл бұрын
@@gilbertlee860 omg
@PrayerChanges24
3 ай бұрын
@@gilbertlee860 “What-the-What??!!”😮😮 Oh my goodness probably told you that to make more money. Then the technicians sits around doing nothing. Because of labor and their time working on customers cars or trucks. This how they make their money!! Awful how these dealerships charge so much money.
@dennardr3391
2 жыл бұрын
Will this work with a 2014 altima?
@TKD187
2 жыл бұрын
Was you check engine light on ? My wife's is flashing lol I've already changed the coil packs and everything involved with that but wants to carve warms up it starts acting very funny and it's hard to get a read on it if you just plug up an OBD plug cuz I was going to show is that it's getting a lean air flow and gas mixture that's all it's going to tell you and in today's world we live in I do not have the money to take it to a mechanic and I've never taken any car I've had to a mechanic but this one is on the verge of blowing up so I have to figure out what it is fast and I only have one day to fix it . This was a nice video but I don't think that's what's wrong with my wife's car because it sounds like a freaking diesel it's definitely misfiring but I change the coil packs and those things were $300 so I don't know what the hell I'm going to do if is something expensive I'm hoping it's just a injection sensor or mass flow air sensor or even a fuel pump those are things that might not cost that much and easy to replace. I just don't want to have to take this engine completely apart again 🤦🏻♂️
@danielpye1784
2 жыл бұрын
i have a 2004 altima 3.5l, when ever you try to accelerate it wants to bog down, do you think possible thottle boby? new fuel pump,battery. any suggestions
@joen2521
2 жыл бұрын
If it never had a throttle body cleaning or replacement before, it would be the first thing I would look at along with the air cleaner and MAS. As mentioned in the video, many things can cause this problem however, throttle bodies need to be maintained (cleaned) to work properly. If you decided to go ahead, remember to disconnect the battery which will also avoid throttle body re-learning process.
@danielpye1784
2 жыл бұрын
@@joen2521 the car has over 200000 miles on it never had any problems like this until now. im going to try and clean it if not i will purchase a new one, thanks
@EliOfMilkyWay
Жыл бұрын
My hesitation was bad ignition coils
@stevesirak
3 жыл бұрын
Yeah right you know that did not Idle right once you move the throttle body by hand you have to do a re learn process or your car will not idle correctly
@lostsul8847
3 жыл бұрын
not true my 08 g35 idles fine with out doing the relearn at all
Пікірлер: 213