5 years later and you saved my wifes car. thanks so much. now ac is blowin cold. mechanic tried to tell me we needed a compressor ac kit.
@lucasstrickland4540
3 жыл бұрын
did this on my 2007. I almost sold it because I was tired of no ac, did this and 20 minutes later I had ac. thank you! you’re a god!
@brianlocal3
7 ай бұрын
Same wires?? I have an 09 and my colors don’t match
@dr1u23m2549
4 жыл бұрын
Want to thank you for this. I found a tutorial on how to fix it with a resistor but was on an older Fusion. I didn't know which wires I needed until your video. In place of the sensor you can just add a 37k ohm resistor between the wires.
@twandaye78
6 жыл бұрын
My brother, you're greatly appreciated for doing this. You just forgot to explain HOW you connected the wires to the sensor. What are those white things that the wires seem to be fed into, and how do I know which side of the sensor to put which wire in?.... When I do this fix, do I need to unplug the car battery first, to eliminate risk of shorting something? ..... If I always leave my air conditioner on the highest setting, will it be better than sometimes putting it on low?....everyone else loaded videos of them doing this, but every here between using a radio shack resistor. What's the differently
@basilkurdi
2 жыл бұрын
I have 2012 fusion SEL, the cable is green, i did the same and it worked like charm. Thank you so much. It costed me 25$ only instead of having the dashboard pulled that was going to cost me around 750$ For the cable i bought it from scrap shop
@letsgonow5641
2 жыл бұрын
How it is holding up so far. I just did this today. Any problems ??
@basilkurdi
2 жыл бұрын
@@letsgonow5641 No problems, all going well so far.
@letsgonow5641
2 жыл бұрын
@@basilkurdi I spent the last 2 Summers and part of this Summer without AC because of this problem...Thank you so much for responding..
@brianlocal3
7 ай бұрын
Where did you get the wiring diagram to know your correct wires
@basilkurdi
7 ай бұрын
@@brianlocal3 It depends on the version of your car, i remember it's mentioned in the Internet somewhere, it shows what the number of the slots you need to use to connect it. But keep monitoring that the compressor is turning on and off . I had a problem after installing this sometimes the compressor keeps cooling without turning off
@tonyhornejr3018
2 жыл бұрын
This is the best video on this part... Straight to the point🔥🔥
@Platinumtag
5 ай бұрын
I did your bypass and mind working fine now...
@ronnierobertsband
4 жыл бұрын
Amazing fix! Easy to do, worked exactly as you described, thank you very much!
@yhyaalree6661
Жыл бұрын
Thank you, my brother. I have a question, what is the problem that may cause with the long time (I have a compressor without a clutch)
@alexytou
4 жыл бұрын
You can cut those two wires on the blue harness, and connect the wires from the evap sensor directly to those two wires (purple and gray) coming from underneath the glovebox. Then you can place the evap sensor inside the air vents and you will have a cycling compressor, avoid freezing on your evaporator and the heater and all climate controls will work properly.
@homeseverafterllc
4 жыл бұрын
When I disconnect the gray wire from the harness no air blows at all. The purple one doesn't change the air from blowing but the gray does it not connected. Any ideas?
@alexytou
4 жыл бұрын
@@homeseverafterllc is this happening on a Ford fusión?
@alexytou
4 жыл бұрын
@@homeseverafterllc just cut the purple wire, and then connect the evap sensor to the cutted purple wire coming from underneath the glovebox. Then leave the gray wire connected and connect the other evap sensor wire to it
@_keepin.it.reel_
4 жыл бұрын
@@alexytou so the purple wire coming out of the harness is cut and not connected to anything but the remaining purple wire from under the dash is connected to one side of the EVAP sensor? Then the gray and blue wire has the other side of the EVAP sensor tied into it fully connected from the dash as well as the harness?
@alexytou
4 жыл бұрын
@@_keepin.it.reel_ that is correct, then You just have to connect the remaining wire from the evap sensor to the gray wire that is still connected to the harness
@michaelabbott2908
4 жыл бұрын
Yo son, you a bad man, worked like a charm. Thanks
@evilss13
6 жыл бұрын
Just did my wifes car. 5 min to make a pig tail. 10 min to install. Thanks alot
@tylerhendrix3303
4 жыл бұрын
Where did you get the connector for the sensor?
@evilss13
4 жыл бұрын
@@tylerhendrix3303 i made it out of a couple simple wire connectors
@moeallan88
6 жыл бұрын
I have a 2013 fusion. Would this be the same? Would I find connectors behind the glove box? Appreciate your help and assistance!
@maksymparker7752
6 жыл бұрын
Appreciate it! Solved my dads ac prob in 10 mins
@Blackyautoelectric
6 жыл бұрын
Max Parker glad it helped!
@tranquilinocalderon180
6 жыл бұрын
Are the wires the same color for a 2012 Ford fusion
@mr2vi5599
4 жыл бұрын
Big thank u!!!!
@msa_0619
6 жыл бұрын
Hello there. Yes I have a 2011 Ford Fusion that have the same problem it will not work on mid day but a/c does work early morning but when I get off from work 5pm it only blow some cool air & warm some time hot air too.can you tell how did you hook it up without removing the dashboard okI live in Houston Tx
@Blackyautoelectric
6 жыл бұрын
Michael Shane hi! Well.. This type of cars had 2 temperature sensors; the evaporator temperature sensor (like the one showing on the video) And the ambient temperature sensor (this sensor is located by the front bumper) what you have to do is to scan the vehicle to see what sensor is the one acting up. Normally when the scanner show -40 on the ambient sensor is either a broken wire or a bad sensor.
@msa_0619
6 жыл бұрын
Robert Reyes Hey Robert Could you tell me where I can get that part that I can install it in my 2011 Ford Fusion SE so can cold air conditioner where is hot outside in the Texas weather. But I have air conditioner early morning but when I get off from midday it's hot but no air conditioner in the car only blow hot air no cold air at all ok.
@candysorbaii
6 жыл бұрын
Robert Reyes what scanner? I'm having the same issue in my 2010 fusion
@dallasharris8753
5 жыл бұрын
I have a 2006 Mercury Milan with same issue . Will this work to solve this problem too?? 💯????????
@carolr.scheiern4107
3 жыл бұрын
Where would you find an adapter connector? Really appreciate your video.
@lisakingston3009
Жыл бұрын
where can i find the adaptor to fit the sensor the dealership . oreillys auto parts didnt have
@jamesriddle7793
6 жыл бұрын
Worked like a charm. Used a bwd pt191 connector from o'reilly/advance (kind of a general connector but it squeezes in) and quick splice connectors. As a side note I found that you could possibly get away with just cutting and capping off those 2 wires but I could be wrong. I say that because if you unplug that whole blue harness the ac will get cold but of course it won't do anything else correctly until plugged back in. As long as those 2 wires arent used to run anything else then it would seem that the sensor itself is unnecessary.
@dragnet53
4 жыл бұрын
That sensor prevents the condenser from freezing up. That is why it is necessary. But thanks for the idea using that PT191 connector. I am going to try it.
@grumpyek
4 жыл бұрын
Gracias por el video! Mé ivan cobrar 350.00 para quitar el tablero...mè horastes una feria ...muchisimos gracias
@michellegregory3344
3 жыл бұрын
I did this and it fixed the problem while in park. But when I start driving it, it blows only hot air again. And when I stop and put it in park it’s back cold. Any ideas?
@SFBay69
6 ай бұрын
My lines are icing up. Id that apart of the problem?
@Blackyautoelectric
6 ай бұрын
Nope. It means that either your expansion valve is bad, or that your lines are clogged up.
@SFBay69
6 ай бұрын
@@Blackyautoelectric I found the problem...my blower motor was faulty
@teddyblankenship782
4 жыл бұрын
did u use a resistor or does the connector plug directly into the pins?
@Blackyautoelectric
4 жыл бұрын
The sensor itself is a resistor... Just buy a new one with the connector.
@ronsimmaculatedetailing6335
3 жыл бұрын
Just pull the dash back. Takes at the most 3 hours with power tools for a first timer. Once u learn the job u can do it in a hour and a half. I understand everybody can't do this but there is a full walthrough video on how to do it the right way here on KZitem
@msa_0619
6 жыл бұрын
Hello Again: Yes I would like to know where I can fine one or get one the connected the wires to the sensor that you have on your video with the EVAP Temp sensor okDo you know I can fine one on E-bay or Amazon or any auto part store? here in Houston TxSo I hope to hear from you real soon ok Oh keep up the good work on here some good video too
@acas336
3 жыл бұрын
Can you shows how to feed the wires and make it? I never done this
@adelarosa0618
6 жыл бұрын
What do you do to the wire on the other side after you connect the sensor?
@georgieshannon6663
6 жыл бұрын
where did you find the connector for the tube ive been to all parts stores and hardware stores nobody has anything at all like that thank you
@Blackyautoelectric
6 жыл бұрын
Georgie Shannon try the connector for the temperature sensor (engine) for a Chevy or the one for the injector in Ford (expedition, f150..) some wire cutters and you good it's not gonna be a perfect fit for the sensor but it will work... The one I'm using is from an alarm that I remove
@georgieshannon6663
6 жыл бұрын
ok thank you i will try
@daniellepender8749
6 жыл бұрын
So where to get the adapter??
@georgieshannon6663
6 жыл бұрын
WENT TO JUNK YARD GOT IT FROM A F150 TRUCK THEY TOOK IT OFF
@roberthydell8751
4 жыл бұрын
You said you can get the plug from a f150 or Chevy but didn't mention what motors or years or anything else. Need to find one for my car.
@Blackyautoelectric
4 жыл бұрын
The 2 pins plug that you find on the temperature sensor in chevy can work or you can buy the evaporator temperature sensor and the connector separately at the auto parts store. Hope this helps!.
@roberthydell8751
4 жыл бұрын
I used a pt191 plug. Had to shave the ears off to fit but worked fine. Took me about 10 mins to fix everything. Great video and thanks for the help!
@technometricglk9252
2 жыл бұрын
you can make a hole in evapurator and instaled in diferent place
@Blackyautoelectric
2 жыл бұрын
I recommend to remove the cabin air filter to see where to make the hole, if you're not careful you can damage the evaporator itself.
@SyedShah-yk4iy
4 жыл бұрын
What's that connector called which you connected with the sensor?
@timothybowling1474
3 жыл бұрын
Whats the name of the adapter?
@kenolpompilus6369
2 жыл бұрын
What's the name of the part you added?
@Blackyautoelectric
2 жыл бұрын
It's the same evaporator temperature sensor that goes on the car (new obviously) I just connected outside the evaporator case.
@kenolpompilus6369
2 жыл бұрын
@@Blackyautoelectric thanks a bunch
@homeseverafterllc
4 жыл бұрын
When I disconnect #15 (blue/gray wire) no air blows at all. #13 (violet/brown) can be disconnected and it still blows.
@Blackyautoelectric
4 жыл бұрын
Dont disconnect them... just peel the wires and add the sensor..
@BWilliam
Жыл бұрын
That sensor can be installed the right way in 30 minutes.
@Blackyautoelectric
Жыл бұрын
Definitely! Thats why people go to the shops.....😅 This is to help out to save money and give this option ...
@BWilliam
Жыл бұрын
@@Blackyautoelectric Nothing wrong with that. 👍
@Sr.RicardoGil-vu5nw
Жыл бұрын
Use black tape for the sensor then close everything bi
@standardautomotive7786
Жыл бұрын
Easy fix, But... Your defrost is no longer going to work.
@moniquekennedy9061
6 жыл бұрын
What's the down side to it
@Blackyautoelectric
6 жыл бұрын
Monique Kennedy well... downside is that the evaporator may freeze and water from condensation may leak inside the car.. which it has never happened to me.
@alexytou
3 жыл бұрын
The compressor will not cycle, and the evaporator will freeze, and the air will stop flowing, until you turn off the a/c to manualy cycle the compresor, then the air will slowly come out again.
Пікірлер: 84