I am a chick having a issue with my ABS sensor and this definitely helped me understand . Just order the parts (left and right) and hopefully it works.
@AIRMANBEAR
5 ай бұрын
DONT FORGET TO GREAE IT TO PROTECT THE SENSOR FROM RUST
@EdChalanto
5 жыл бұрын
Thank you
@73superglide62
5 жыл бұрын
Your welcome hp it helped
@Captainpook12
3 жыл бұрын
Does in matter ho it goes into the clip or does it have to be facing a way
@73superglide62
3 жыл бұрын
Should matter but if not locken in .will set the code again
@Jenna-zv6ve2sx4u
Ай бұрын
when you take off the sensor by the hub, how does it come off? does it clip on? do you just pull it off?
@73superglide62
29 күн бұрын
REFRESH ME THE COMPASS ? SPEAKING
@Jenna-zv6ve2sx4u
29 күн бұрын
@@73superglide62 anyway i found out the code its a c1043 i wish it was just the sensor, so i will have to take it to the mechanic.
@briansawyer3232
Жыл бұрын
Th ask for the video,it would have been nice to cut out a lot of the video to Kane it more simple to see the important parts but other than that thanks!
@bradperry604
Жыл бұрын
I don't see a jack stand!
@spartancaptain5691
5 жыл бұрын
What problem were you having that you replaced it?
@donnieshepperson126
4 жыл бұрын
rear wheel sensor
@Udahn22
4 жыл бұрын
Warning lights. Like a lot on and eventually the car won't want to shift out of first. ABS 4x4 lights and a few others are on.
@AIRMANBEAR
5 ай бұрын
THE BRAKES WILL COME ON WHILE DRIVING (VERY DANGEROUS)
@anareel4562
11 ай бұрын
Plugging the sensor back in is the worst part of the job for real
@km351c6
2 жыл бұрын
Looks like your are just replacing the wheel sensor wire harness not the wheel sensor . A little misleading.
@73superglide62
2 жыл бұрын
All in one dude
@AIRMANBEAR
2 жыл бұрын
@@73superglide62 I CANT SEE HOW YOU ARE REMOVING THE OLD SENSOR .. DOES IT JUST PULL OUT WITH NO BOLTS HOLDING IT IN?????????????
@73superglide62
2 жыл бұрын
@@AIRMANBEAR there a little clip holds it there
@73superglide62
2 жыл бұрын
More money's lost utube do your job
@AIRMANBEAR
2 жыл бұрын
What a stupid design by jeep.... that clip is so thin it rusts away to nothing and the sensor just falls out.. NOW I HAVE TO REPLACE THE WHOLE WHEEL BEARING HOUSING TO GET A NEW THIN CLIP.!!!!!!
@AIRMANBEAR
Жыл бұрын
you can help the rust problem by coating the sensor clip with grease before it rus away.
@mikesmith9440
Жыл бұрын
That’s where I am right now. I gotta go buy a whole new hub assembly because my sensor clip rusted away. I held it in there with epoxy for about 8 months but now it’s loose again lol.
@AIRMANBEAR
Жыл бұрын
@@mikesmith9440 YOU THANK THE JEEP DESIGNERS FOR SUCH A STUPID DESIGN ....ANY IDIOT CAN TELL IT WOULD RUST AWAY QUICKLY .. COMPLAN TO THEM OR THE NHSTA BECAUSE ITS A SAFTY THING TOO..
Пікірлер: 29