Your video really helped us, we had the same problem with our challenger. Your the only video who actually helped us.
@wedoitall7676
Жыл бұрын
Glad to help. Thank you for your comment and subscribing. You are appreciated
@chrisclaxton2350
4 ай бұрын
Outstanding my dude, All the video's and post's I have seen had the intake manifold removed. going to go out and give this route a try thanks.
@wedoitall7676
3 ай бұрын
Glad we could help. Have a blessed day!!
@madmike4043
4 ай бұрын
Thanks bro, i used this method for tie rod bushings on a intrepid but wouldn't have tried on my own without your video. Man its tight
@wedoitall7676
3 ай бұрын
Truly appreciate you. Glad it worked out!!
@garywade6313
11 ай бұрын
I plan to tackle this job on my personal vehicle soon. Thanks for the insight, I'll be sure to keep all the information received from you in mind and check back in letting you know the outcome. Thanks again.
@wedoitall7676
11 ай бұрын
Take your time...you got it. Glad I could help
@garywade6313
11 ай бұрын
I started the process, having a bit of a challenge getting the socket onto the bad sensor. Any advice ?
@wedoitall7676
11 ай бұрын
@@garywade6313 did you get the specific Socket for the sensor, like in the video. That Socket is made for the tight space
@garywade6313
11 ай бұрын
Yes I did thanks. I'll make it happen.
@garywade6313
11 ай бұрын
It's all complete, thanks for all your assistance.
@locaventura2023
3 ай бұрын
I'm glad I saw this video thank you so much dude God bless you
@wedoitall7676
3 ай бұрын
God bless you also. Thanks for stopping by!!
@BigBurrito818
7 ай бұрын
Going to tackle this weekend, thank you!
@wedoitall7676
7 ай бұрын
You got it...glad 2 help
@carlosdanger1
Жыл бұрын
Good job man. Thanks for the video.
@wedoitall7676
Жыл бұрын
No problem at all
@calebevands9270
9 ай бұрын
The best way to do it. Is to take your whole intake off all the way down to the oil filter housing. And then you have all the room you need.
@wedoitall7676
9 ай бұрын
Thanks for the comment. I'm sure there are better ways to get it done...this was the most efficient way for me at the time. Be blessed!!
@thomasorcher7891
Жыл бұрын
A RT is 5.7 V8 that's a V6
@wedoitall7676
Жыл бұрын
It was badged as an rt...didn't really pay to much attention... Thank you
@lamontwalker5891
Жыл бұрын
I need this done . How much should something like this run? Or should I say how do I know if I'm being taken for a ride
@wedoitall7676
Жыл бұрын
It depends...if you are going to the dealership they will remove the intake, upper and lower. You may be looking at close to $700. A shop may use this method and should be around 2-300 dollars...this is just an estimate based on the time it took. Try repairpal.com that may give you a better price quote
@saintsfan7268
Ай бұрын
Do I need a special socket for the oil sensor
@wedoitall7676
Ай бұрын
For this method....yes you do. I explained it in the video so you can have a better idea
@user-vw5uz8ee9u
6 ай бұрын
How much will it cost to replace a oil sensor switch
@wedoitall7676
6 ай бұрын
It all depends on where you get it done. The sensor is between 40 and 60 and labor could be between 100 and 150. Everyone has different prices
@seriousbeatz
Жыл бұрын
Did the car start up after the censor was replaced. ?
@wedoitall7676
Жыл бұрын
Yes. The car will start even if it's bad. It will normally just trigger a check engine light
@aaronhudgins5810
4 ай бұрын
Does that fix the oil temperature from running hot
@cristoffermimilaguzman9527
10 ай бұрын
Hey man about how much time did it take you to complete the job ?
Пікірлер: 36