For everyone watching this incomplete video: To remove the WIN module you must take off the lower panal on the drivers side. remove the metal panal below it. Remove the right metal bracket blocking access to the module. Then remove the cluster.You can now get to the 3 bolts that hold the win module bracket.Then remove the win module and bracket as one piece. Hopes this helps the people that ended up watching this video looking for win module replacement instructions.
@bryanbridgforth6651
2 жыл бұрын
Thanks for this comment! I'm going to attempt to replace mine... are there any special tools needed to remove the WIN module?
@lccdan1
2 жыл бұрын
@@bryanbridgforth6651 NO special tools but you will have to deal with a lot of snap in plastic panals and parts that you will think will break when you pry them out. Other than that it is just screws and bolts.
@bryanbridgforth6651
2 жыл бұрын
@@lccdan1 so just Phillips head screws?
@lccdan1
2 жыл бұрын
@@bryanbridgforth6651 Some have bolt heads 7mm,8mm and maybe one other. There is also torx head screws holding in the cluster.
@bryanbridgforth6651
2 жыл бұрын
@@lccdan1 thanks a ton man!!
@user-pp7dt6kk6v
8 ай бұрын
Been down this road. Same symptoms. Mine was cam poisoning censor. Oooand yes don’t hang heavy keys off your fob Will create problems
@basilalhamady4898
3 жыл бұрын
How did u fix the issue ? What is the part name/number? I have the same issue ... Do have another video describes more ... Thank u mate
@joedimauro1065
3 жыл бұрын
Okay so I had the recall done on fuel pump and then my car started stalling I had a bypass jumper installed and fixed
@joedimauro1065
3 жыл бұрын
The bypass did not work nor did the fuel pump the tipm spark plugs coils I’m done trading it in all done with dodge
@joedimauro1065
3 жыл бұрын
Started stalling again tried tipm fuel pump torque converter clutch solenoid valve body conductor plate throttle body is spotless new air filter I think it’s the computer but I’m done trading it in
@joedimauro1065
3 жыл бұрын
Sold the car
@tylerrudd8174
3 жыл бұрын
So my 2013 Durango recently started stalling out while starting. (Push button ignition) the remote start quit working. Now occasionally while tryin to start the Durango it will start then immediately stall out, then usually takes 2-3 tries to start it but then it runs just fine once it takes off. Anyone else have a similar issue?
@basilalhamady4898
3 жыл бұрын
I have the same issue
@MrJumartinez449
3 жыл бұрын
I got a recall for mine .. fuel pump relay it had it changed once. But looks like that recall got a recall..lol
@mrtejada8796
3 жыл бұрын
It’s a recall take it the dealer. Fuel pump relay
@myawells7160
3 жыл бұрын
Did it shake
@zipzay2037
2 жыл бұрын
2012 Dodge Charger 3.6 stalls when flooring it at high rpm’s
@ryansoltysiak4072
Жыл бұрын
What was your fix on that? 2014 durango 3.6 stalls at 4K rpm.
@AC-wm2mi
5 жыл бұрын
Is your vehicle working properly now did that fixed the problem
@tubeblack49
5 жыл бұрын
It did fix it.
@AC-wm2mi
5 жыл бұрын
Could you please tell me the name of the part that you replaced
@tubeblack49
5 жыл бұрын
@@AC-wm2mi the part number is in the video.... towards the end I show it and describe it.
@juanfuentes8458
9 ай бұрын
I spent $300 on an original key and now I need the module😮
@thefacelessskeleton7714
4 жыл бұрын
How did you get to the WIN? Through instrument cluster? Do you have another video you can share on that?
@tubeblack49
4 жыл бұрын
Yes. And from underneath.
@thefacelessskeleton7714
4 жыл бұрын
Do you have a video? Can you share that link please if you do? I have same 2013 Durango. Had the WIN module come into today. Im just not sure the best way to get at it.
Пікірлер: 33