Thanks for sharing this. This is a common problem. My 2007 jeep is stuck in Limp mode 2nd gear. 91k miles. I'm going to try and reset it.
@ovidiucaliman242
3 жыл бұрын
Help!(3.6 V6 2013 jku AUTOMATIC TR) I got a check engine light on, limp mode and error P0339( CRANKSHAFT SENSOR INTERMITTENT). I change the sensor and check wires (5.02Volt,no short circuit), and I didn't find anything. where would the problem be? thanks
@BakedDaily
2 жыл бұрын
2013 Jeep jk slips 3-4 but doesn’t slip if I let off gas when moving also goes into limp mode occasionally it used to do it every now n then but now it’s all day everyday I have to keep shutting off n on
@CrowtownAuto
2 жыл бұрын
Definitely sounds like this could be your issue. It's certainly the easiest thing to check off the list. If it's not in the control module it could be in the actuator in the TC
@irvincanto2995
Ай бұрын
Got a p0882 low voltage code and in limp mode in 2011 jeep liberty wonder if this is the same makeup
@CrowtownAuto
Ай бұрын
Could possibly be. make sure to go through the other possible causes, battery, charging system, connectors, etc as well
@irvincanto2995
Ай бұрын
Thanks for the reassurance i was on the task when i asked and still am though almost done i found almost all connections and ground had build up and little corrosion hopefully this does it @@CrowtownAuto
@irvincanto2995
Ай бұрын
We forget that it's important to keep these clean and clear as possible
@irvincanto2995
Ай бұрын
🤙
@ralphie6000
4 жыл бұрын
i got a check engine light and a u0414 code on my 2016 wrangler, would a new TCM help me ?
@CrowtownAuto
4 жыл бұрын
It could possibly but it sounds more like that's an issue with the transfer case control module. Hope you get that one figure it out, it seems like one that can be misdiagnosed by dealerships and you'll be chasing it around for a while if it's not figured out quickly.
@ralphie6000
4 жыл бұрын
Crowtown Auto thanks man still haven’t been able to get it fixed, and the tccm is only a dealership part but they are telling me i don’t need that
@JustinReynoldsLocal25
3 жыл бұрын
I got code p1731, cleared the code but mine 2013 Wrangler Sahara won’t go past 2nd.
@andresguerrero5330
17 күн бұрын
Did you ever get it figured out. Im having similar problem @ralphie6000
@snipersxxs
2 жыл бұрын
I got error U0101 Mass dont know what wrong with Transmission
@CrowtownAuto
2 жыл бұрын
That means the transmission lost communication with the TCM. could be something came unplugged or your TCM is bad
@snipersxxs
2 жыл бұрын
@@CrowtownAuto Thanks for your fast response i ll do as you said ll let you know
@BPKROME
2 жыл бұрын
Do you mind telling me what it was doing that you had to change this piece? I'm having shift issues right now where mine only stays in 1st gear. Before I would turn it off and turn it on and it would fix but now it only stays in 1st
@CrowtownAuto
2 жыл бұрын
This was removed from a wrecked jeep for a customer. I'm unsure of their symptoms. Sounds like your issue could be from this module. If you can source one for a decent price, it'd be easier to try than removing your T-case.
@BPKROME
2 жыл бұрын
@@CrowtownAuto I really appreciate your reply man.
@TheeJohnMan
Жыл бұрын
Did you have to reprogram the new tcm?
@CrowtownAuto
Жыл бұрын
This was pulled for a customer who purchased the module. In most cases you would probably need it flashed or synced to your vehicle except on the off chance your numbers match those on the replacement module.
Пікірлер: 24